Search Documents

By George A. Connell

BORAX, a sodium borate and the principal sodium salt of boric acid, has been surrounded with romance and with a certain amount of mystery. Its early history is not entirely known but it has been contended that Marco Polo in his travels in the Orient introduced this material to the West during the Middle Ages. Without doubt its first source was from Central or Eastern Asia and perhaps from Tibet. The well-known fluxing properties of borax probably introduced its earliest use that of a soldering flux in the manufacture of jewelry. This use, as well as the remote location of most borate deposits, added greatly to the romance associated with the thought of borax. COMPOSITION The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture of disodium tetraborate (Na2B4O7.10H2O), and, further, can be considered as the acid salt of monosodium metaborate. However, the term "acid salt" might imply that borax gives an acid reaction in solution, which is not true, since solutions of borax are decidedly alkaline, giving a pH of 9.2. Boric acid, also known as boracic acid, has the chemical formula H3BO3; it occurs in nature as the mineral sassolite. Sassolite has been

Jan 1, 1949

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

Cortez Gold Mines operated a conventional 2,100 mtpd (2, 300 stpd) cyanidation plant until the 5 million ton ore body was worked out in 1973. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME 1975.) Sub-grade material was dump leached at the mine -mill location in 1971, and the resulting pregnant solutions were added to the feed in the plant&apos;s Merrill-Crowe precipitation unit for gold recovery. In early 1973, however, Cortez put into operation their Gold Acres mine which was located about 13 krn (8 miles) to the west of the &apos;Cortez mine. Economics at that time dictated the heap leaching of the lower grade portion of the ore body with the higher grade being trucked to the Cortez plant for milling. Leach ore was moved directly from the open pits to prepared leach pads located on a gently sloping terrain of 570 grade. Preliminary pad preparation at the leach site included removal of vegetation which was composed of sagebrush and grading of the base. Pads were comprised of mostly minus 74 micron (200 mesh) materials and were made of clay-silt or slime tailings spread on the pad area in thin 50 to 75 mm (2 to 3 in. ) layers, compacted with a vibrating roller compactor to a depth of about 380 mm (15 in.). This was followed with a 100 mrn (4 in.) layer of coarse rock to prevent erosion on the pad and to allow solutions to move laterally under the heaps. Leach solutions normally traveled the length of the heaps and were collected in plastic-lined ditches from which they flowed by gravity to the pregnant solution storage pond. Both pregnant and barren ponds were constructed in the same manner as the leach pads - being lined with compacted tailings or clay silts. The Gold Acres facility required pregnant solution storage of 6 million liters (1.6 million gal) and barren storage of 3.8 million liters (1.0 million gal) designed to handle two to three days of heap drainage or to retain run-off from a major rainfall. Various heap heights were tried including 3, 6, and 9 meters (10, 20, and 30 ft), with a 6 m (20 ft) height selected. Ore was dumped by trucks in a single 6 m (20 ft) lift using a D8 Caterpillar dozer for

Jan 1, 1981

By Louis A. Riley

I DESIRE to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomer¬ates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideration in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

Jan 1, 1877

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for &apos; military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,&apos; but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for &apos; military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,&apos; but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.&apos;, n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " &apos;.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.&apos;,&apos; Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a&apos;=-n;s/= nD,(qo);"; and b&apos; = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

May 219t, 1872. THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-four papers, by twenty-six authors, have been read. These papers embrace s wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue s volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. It is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit s more ambitious publication.

Jan 1, 1873

THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-Bur papers, by twenty-six authors, have been read. These papers embrace a wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue a volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. I t is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit a more ambitious publication.

By S. W. Parr

FRom a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows: Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric acid— 1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60" C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present. Sulfur in the form of iron pyrites, or marcasite, may be quantitatively removed without oxidation of the organic sulfur as follows: A dilute solution of nitric: acid is prepared having 1 part of concentrated HNO3 to 3 parts of water or with an approximate specific gravity of 1.12. The coal sample, ground to 100 mesh, is digested with this solution at room temperature for 3 or 4 days, filtered and evaporated to dryness, taken up with water, and acidified with hydrochloric acid. It is now ready for precipitation with barium chloride in the usual manner. If sulfate is present in the original sample to an appreciable amount, it should be removed by the procedure outlined above. It is not necessary here to give the methods for determining the two

Jan 1, 1920

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6&apos;7 French has considered this effect from both theoretical and experimental aspects. In French&apos;s studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6&apos;7 French has considered this effect from both theoretical and experimental aspects. In French&apos;s studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By T. Fraser, F. F. Giese, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of free impurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal. The coal at Shamrock No. 1 is mined from the No. 2 Gas seam. It is made up essentially of a low ash coal suitable for byproduct use with one or more bands of splint coal of higher ash content suitable for industrial fuel. The washing plant was installed for the two-fold purpose of removing the free impurities incident to mechanized mining and to separate the run of mine coal into the two types. To accomplish these results it is necessary to make a separation at a specific gravity of about 1.4 to recover the byproduct coal and to separate the splint coal from refuse at a higher gravity. The coarse coal section of the washing plant was put into service about 10 months before the fine coal section was completed. Inadequate screening capacity in the raw coal preparation plant resulted in a portion of the fine coal being fed to the jigs. No provision for preliminary dedusting of the raw coal feed was incorporated in the design. Under the conditions in the initial operating period, separation at the desired lower gravity was not realized, apparently because of the presence of an excessive amount of fine solids in suspension in the wash water. Difficulty in wetting the fine coal may also have been a contributing factor. Additional facilities for the removal of the fine solids from the wash water was indicated. Information then available on the Driessen cone for this purpose was studied and a cooperative agreement with the Bureau of Mines for experimental work with a unit of standard size as developed by the Dutch State Mines was arranged. During the time required for construction of the cone it was found the addition of a small amount of wetting

Jan 1, 1950

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.&apos; Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.&apos; The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By R. L. Sandefur

Professor Kim&apos;s excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate. Kriging is the procedure which finds the weighing coefficients which minimize the estimation variance [ ] is the variance of blocks like the one being estimated. wi is the covariance of the estimated block and the i-th sample. oij is the covariance of the i-th sample and the j-th sample. Ai is the weighing coefficient for the i-th sample. N is the number of samples. The formula for estimation variance can also be used to calculate confidence limits on blocks estimated by any linear combination of sample grades including: 1) Polygons a. Hole nearest block centroid is assigned weight 1. All other holes are assigned weight 0. b. Polygonal area weighing. The samples are assigned weights directly proportional to their polygonal areas of influence within the block. The weights sum to 1. 2) Inverse distance weighing. The samples are assigned weights directly proportional to the reciprocal of their distance to some power from the block centriod. The weights sum to 1. Often only holes nearer than a certain distance and/or the nearest hole in each octant is considered. If there is an antisotropy to the ore body, an elliptical transformation often gives more accurate results. The most popular inverse distance weighing function is inverse squared distances (IDS). 3) Simple average. All samples within a certain distance are assigned the same weights which sum to 1. As an example of the applicability of the above formula to any linear estimate an internal verification on copper grade of 665 blast holes on the 1040 bench at Utah&apos;s Island Copper mine is presented. Internal verification is simple and applicable to non-linear estimates as well. Any sample (drill hole, bulk, trench, or chip) is dropped out, the value of the dropped sample estimated and compared with the actual value. If this is done for all samples, a measure of confidence limits is obtained. Internal verification is used in Cominco&apos;s MEPS system4 and in the BLUEPACK system.5 Comparison of block values against estimates697 is not dissimilar to internal verification. Results of the internal verification are presented below:

Jan 1, 1980

By Earl C. Herkenhoff

Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95% of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978. "Separation of Bitumen from Dry Tar Sands," was the first blockbuster. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high &lids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95OC (203°F) in a 0.3 m solution of sodium carbonate-about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60.62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let&apos;s mine heavy oil and tar sands.

Jan 1, 1983

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials&apos; but for the technically important grain-oriented 3 pct Si-Fe&apos; the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956

By D. S. Hutton, W. C. Leslie

Thermal etch patterns developed on poly crystalline 3.5 pct Si-Fe by heating in hydrogen or in argon have been examined. The most prominent feature of the etching is the development of striations on grains with (100) planes near the plane of the surface. These striations are probably produced by the resoution of a random, high-energy plane into (100) facets of lower energy. THE thermal etching of iron and iron-base alloys has a long history. The phenomenon was observed by Osmondl more than 70 years ago. The literature on thermal etching between that time and 1951 was reviewed by Olney,2 and a briefer review appeared in 1958. 3 The only articles which have been found dealing with the thermal etching of silicon iron are those of Dunn and Lionetti4 and of Dunn, Daniels, and Bolton,5 and they reported only grain boundary etching. EXPERIMENTAL PROCEDURES A cast 3.5 pet Si-Fe alloy was given a metallo-graphic polish and etch, then placed in flowing purified hydrogen for 6 hr at 2200°F. The same specimen was later repolished and etched to remove the thermal etching. The specimen was then held in flowing purified argon at 2200°F for 72 hr. In both instances the specimen was rapidly cooled by being pulled up quickly into the cold zone of the furnace. All photomicrographs shown are of the surface as removed from the furnace. Oblique illumination was essential for observation of the thermal-etching effects with a light microscope and was used for all the photomicrographs. RESULTS AND DISCUSSION Grain boundary etching, grain boundary movement, and contouring within grains are illustrated in Fig. 1. The contours within a single grain followed behind the advancing grain boundary. To determine the average contour interval, or step height, white light was used in an interference microscope. The steps were of the correct magnitude to separate while light into its spectrum of colors. A green light was focused at the top of a contoured area, shifting to red across the field. By using the difference in the dominant wave length of red and green light,6 and counting the number of steps across the area, it was possible to obtain a value of about 80A for the average step height. Laue back-reflection patterns of four grains with contour lines showed that the grains had a (100) plane slightly inclined to the plane of the surface (± 5 deg). Insofar as this could be determined from their irregular traces, the contour lines within a grain had a common direction, <100> ± 5 deg.

Jan 1, 1961