Search Documents

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., ('1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944

By R. H. Terhune

THE enormous production of pig-iron, together with the many difficult and interesting problems with which its manufacture is fraught, 11as secured to this industry the exclusive attention of scientists with reference to the chemistry of iron, while some of the minor departments of its metallurgy have suffered neglect. Particularly is

By R. E. Reed-Hill, W. H. Hartt

The second order, {1011}-{1012} twin bands observed in critically deformed magnesium are often accompanied by an unusual form of kinking. These kinks, which lie adjacent to and run more or less parallel to the twin band habit, allow plastic deformation that occurs inside the twins to be accommodated into the matrix. The bend planes of these kinks cannot be explained using slip dislocations with Burgers vectors lying in the basal plane. A mechanism involving a single set of {1012)(1011) dislocations is proposed to account for the kink band habit, in good agreement with the experimental observations. It has been shown that second order, {101l)-{1012} twinning is an important phenomenon for magnesium deformed in the ambient temperature range. A detailed study of these twins has recently led to a better understanding of their irrational habit plane1 and their relation to fracture in magnesium.' This paper is concerned with a third aspect of these twins; this being the kink bands, originally referred to as shear accommodation kinks,3'4 that are often induced in the adjacent matrix. A twin band and its shear accommodation kink usually appear as a single macroscopic deformation, as seen in Fig. 1. The complex nature of these deformed regions is easily revealed, however, with the aid of a suitable microscope. It has been proposed374 that the primary function of these kinks is to accommodate the nonhomogeneous deformation that normally occurs in the second order twins. The twins tend to form as small discrete lamellae lined up approximately one in front of the other.''' Very large plastic deformations varying in magnitude from one twin to the next, may occur inside these lamellae. The kinks serve both to pass this strain into the matrix and to accommodate strain variations between twins. Deformation within the kinks, subsequent to their formation, has also been observed;3,4 and it is thought that this contributes to the strain accommodation process. The bend planes of the kinks have a habit near that of the twin band itself, which lies about 56 deg from the matrix basal plane. This orientation does not bisect the angle formed between the basal plane to either side of the bend plane and therefore differs markedly from the kink structure usually observed in hcp metals.'-' The present paper reports the results of a study of shear accommodation kinks and proposes a possible solution to the problem of the orientation of the bend plane. EXPERIMENTAL PROCEDURE Rectangular cross-section tensile specimens with axes parallel to (1010) and faces to (1210) and (0001) were cut and acid machined from a high-purity magnesium single crystal. After straining on an Instron machine the specimens were examined by both optical and replica electron microscopy. The basic procedures have been previously reported."' EXPERIMENTAL RESULTS AND DISCUSSION Structure of Shear Accommodation Kinks. A typical, large (101l)-{1012) twin band with its associated shear accommodation kink is shown running diagonally from upper left to lower right in Fig. 1. In this optical micrograph the twin band, consisting of a row of small, highly deformed twin lamellae, is visible as a narrow dark band along the left hand edge of the structure in question. The kink lies to the right of the twins, is approximately three times as wide, and is lighter in contrast. The horizontal slip lines visible on the general specimen surface correspond to matrix basal slip and are parallel to the tensile axis. Note that on the right-hand side of the band these slip lines can be followed from the matrix into the kink. At the kink band boundary the slip lines suffer a clockwise rotation of about 25 deg. Rotations of this magnitude are not uncommon. When a surface such as that in Fig. 1 is given an etch1 making it sensitive to polarized light, it has been observed that the slip traces in the kink are parallel to the basal plane trace in this region. This is in excellent agreement with the assumption that these regions are indeed kinks. Fig. 2 is an electron micrograph of this same twin band and kink. Note that a row of small supplimation pits has formed

Jan 1, 1969

By Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were re- opened and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties.

Jan 4, 1951

By Frederic P. Dewey

By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called, platinum. Sometimes it is SO, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes gives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid,' I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Jan 1, 1913

By Persifor Frazer

COMPARATIVE columns expressing the series of rocks of the lower half of the Mesozoic age in this country and in Europe are not yet definitely established. The following represents a co-ordination of the beds in England and Germany,* with a list of materials to be worked in from this country. † * Cotta, " Geologic der Gegenwart." † Section from York to Dillsburg. Report C, 1875; Second Geological Survey of Pennsylvania.

Jan 1, 1877

By George Stone

THE stack gases from regenerative furnaces are very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300° C. (572° F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450°. The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the .boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 10, 1913

By William H. Baer, George M. Carlton, Blake M. Loring

IT is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen.1,2,3 Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). EXPERIMENTAL PROCEDURE The material for this investigation consisted of extruded rods 1 ¼ to 1 ½ in. in diam. The chemical compositions were as follows: [ ] The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0-015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to ±3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements.

Jan 1, 1948

By C. R. Kyle, R. L. Perrine

A transparent model of a reservoir has been used to study some characteristics of instability in miscible displacement. The linear model dimensions are 1/4 in. x 91/2 in. x 10 ft. The model is packed with spherical glass beads. Thee groups of experiments have been performed. The objectives were to measure, respectively, the rate of growth of the transition zone, flow velocity variations in the transition zone, and the effect of a graded viscosity zone on stability. All experiments were compared, where possible, with theory. The transition zone grew almost linearly with distance traveled, regardless of flow rate, where adverse viscosity ratios were used. At very adverse viscosity ratios and large distances traveled, some reduction below linear growth was noted. This could be attributed to the effects of mixing. General similarity in flow pattern was commonly shown in different tests, although exceptions occurred at the higher viscosity ratios. Injection of tracer spots permitted direct experimental measurement of velocity variations. Statistical methods were used to compare observed velocity variations with recently published theories. Surprisingly good agreement with some theoretical predictions was obtained. In the experiments using an initially graded viscosity zone, macroscopic stability was reached before predicted by theory. Under conditions theoretically considered to be slightly unstable, any fingering tendency was too slight to become observable within a 10-ft long system. The general correlation of all experiments with published theory was good, and suggests that theoretical predictions can be extended to reservoir problems. INTRODUCTION Early laboratory studies of miscible displacement demonstrated the high recovery efficiency possible with this method. Linear laboratory models showed that, under some circumstances, all in-place hydrocarbons could be recovered using as little solvent as 5 per cent of the pore volume. These results led to a series of pilot field projects. Under realistic conditions, however, other laboratory studies showed that a small solvent bank may not recover much more oil than a conventional gas drive. The cause of this lack of efficiency is unstable viscous fingering. The size of the solvent bank required to give optimum recovery is, therefore, a question of great economic significance. The object of the experiments described in this paper was the quantitative measurement of unstable flow parameters, the verification of present theories on the miscible displacement process, and correlation of these theories with ex peri mental observation. Of the theories which have been advanced, those by Dougherty, Koval and Perrine show promise of predicting reservoir performance with reasonable accuracy.l-7 The present experiments were correlated, where possible, with the theories of Koval and Perrine. Dougherty's theory was not used because of the additional computational difficulty it presented and the belief that no further information would result. EXPERIMENTAL EQUIPMENT A transparent reservoir model, consisting of a vertical reinforced plexiglass column, was used for the experiments. The column was packed with glass beads, which served as the porous medium. To induce a known velocity disturbance in the flow, a double cosine wave restriction in the transverse cross-section was placed at the top of the column. To mark the flow field and provide a means of measuring the local fluid velocity, a dye-spot injection system was provided. The column was 10 ft high by 1/2 in. wide by 1/4 in. deep. The cosine restriction was placed 16 in. from the top of the column. The glass beads were smooth and spherical and had a mean diameter of 0.0102 cm. Liquids entered the top of the column through a manifold allowing three points of entry (left, center, and right, or any combination of these). A positive-displacement pump with variable-speed drive was used to control liquid flow rates. The pump transferred viscous oil from a reservoir to an accumulator, which displaced the test liquid into

Jan 1, 1966

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By G. C. Bernard, L. W. Bernard, L. W. Holm, W. L. Jacobs

The effect of loam on the permeability of porous media to water was studied as a {unction of foaming agent concentration, specific permeability, pressure gradient, length of a porous medium and its oil saturation. At a given fluid saturation in a porous medium, the permeability to water was found to be the same whether loam was present or not. Foam decreases the permeability to water by developing a higher trapped gas saturation than that obtained by water flooding without loam present, increasing the concentration of foaming agent increased the trapped gas saturation and thereby decreased the permeability to water. The presence of oil reduced the capability of most foaming agents to decrease the permeability of a porous medium to water. A few surfactants were found to be effective loaming agents even in the presence of oil. These results are similar to those reported in a previous paper on the effect of loam on the permeability of porous media to gas. The effect of loam was found to persist in long porous media at moderately high reservoir temperatures and during the passage of many pore volumes of surfactant-free water. INTRODUCTION This paper describes part of a study on a novel approach in the use of surfactants for oil recovery; the use of foam rather than water to displace oil. Previously it was found that foam can displace oil which normally is not displaced by water.4 The foam is formed by successively injecting a suitable surfactant solution and gas into a porous medium. Foam appears to have at least two uses in the field: (1) it shows promise as a superior oil recovery agent, and (2) it shows promise as a selective permeability reducing agent. Foam may be very useful in water floods, or in other oil recovery processes, where highly permeable streaks or unfavorable mobility ratios are a problem. A previous paper reported the effect of foam on the permeability of porous media to gas.1 In the present study the effect of foam on the permeability of porous media to water is reported. The specific objectives of the study were to determine: (1) the effect of foam on the permeability to water in porous media of various specific permeabilities, (2) the effect of foam on the permeability to water in the presence of oil, (3) the effect of foam and crude oil on the trapped gas saturation, (4) the effect of foam on permeability to water at trapped gas saturation, (5) the effect of pressure gradient on the permeability to water under foaming conditions, (6) the persistence of foam during the passage of surfactant-free water through the porous medium, and (7) the effect of various foaming agents, length of the porous medium and temperature on the permeability reduction caused by foam. EXPERIMENTAL PROCEDURES EQUIPMENT AND MATERIALS The experimental apparatus consisted of consolidated and unco n soli dated porous media, wet test meters and constant delivery pumps. The porous media consisted of consolidated sandstone cores (6 to 36 in. long), and unconsolidated sand packs (3 to 30 ft long). The consolidated cores had permeabilities of 32 and 1,000 md and porosities of about 20 per cent. The sand packs had permeabilities of 3,500 to 211,000 md and porosities of about 40 per cent. (Throughout this report a term such as 100 md sand" is used. This term means that the porous medium had a dry, nitrogen permeability of 100 md.) Fluids used in the experiments were distilled water, 1 per cent NaCl solution, aqueous solutions of foaming agents, nitrogen gas, air and crude oil.

Jan 1, 1966

By E. I. Alessandrini, A. U. Seybolt

Selective oxidation (preferential oxidation of a single alloy component) can be an important oxidation mode in the case of alloys such as Si-Fe, Al-Fe, and so on, when heat-treating in atmospheres of low oxygen potential. It was the purpose of this work to identify the oxide films formed on iron containing 31/4 pct Si at low oxygen potentials, and to make some observations on the H2O/H2 ratios required to form them. EXPERIMENTAL METHOD HYDROGEN of varying water content offers a very convenient method of establishing a wide range of oxidizing power, or oxygen potential. The method chosen to provide a desired H2O/H2 ratio was to nearly saturate hydrogen at room temperature by bubbling the gas through water at room temperature, and then to wring out the excess water by passing the wet gas through a long glass spiral immersed in a refrigerated liquid at a desired dew point. After oxidation, the samples were examined by electron diffraction in order to identify any film which might be present. PREPARATION AND TREATMENT OF SAMPLES The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron and 96 pct ferro-silico11, vacuum-induction melted, hot-rolled then cold-rolled to 0.015-in. thickness. After the cold-rolling the samples were annealed at 1000°C. Transmission Laue X-ray patterns showed very little evidence of preferred orientation, but it is likely that a weak texture could have escaped notice. The chemical analysis was as follows: 3.34 Si, 0.01 Al, 0.001 0, 0.006 C, 0.002 N. Before each sample was oxidized, it was polished through 4/0 emery paper, cleaned and dried using benzene, carbon tetrachloride, acetone, absolute alcohol, and ether. The method of oxidizing the samples was as follows: Samples about 1/2 by 1 by 0.015 in. were held in the upper, cool part of a vertical vacuum furnace until the desired temperature was established in the furnace, Fig. 1. The sample was then lowered into the uniform hot zone where it was heated quickly to the desired temperature, and subjected to hydrogen of controlled moisture content (dew point) as mentioned previously. Temperatures from 400" to 1000°C were used, and dew points from room temperature to —78°C were explored. In general, the runs lasted about 6 hr, but a few runs were of different duration, as will be indicated later. After the predetermined period of time had elapsed, the specimens were withdrawn by the hollow stainless steel-quartz holder to a cool zone at the top of the furnace. EXPERIMENTAL RESULTS The results are summarized in Table I. Most of the electron-diffraction patterns were obtained by glancing-angle reflection, but in a few cases it was possible to strip the oxide films from the surface by a total immersion in a 3 pct bromine-methanol solution. Some of the thinner stripped films yielded quite satisfactory transmission patterns. However, both diffraction techniques yielded the same results; the patterns while most frequently showing a (low) tridymite, also showed a (low) cristobalite in some cases. A few patterns showed evidence of both phases. Because of the known nonequilibrium behavior of silica, it is not surprising that both forms of silica could coexist on one sample. It was noted that at fairly low dew points such as —40°C, there was a tendency for diffuse diffraction rings, suggesting a very small crystallite size. Also some subsequent experiments to be reported later show that thin silica films can be amorphous.

Jan 1, 1959

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.'-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.'- '' It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968

By Elmars Ence, Harold Margolin

The partial isothermal section of the Ti-Cu-Zr system at 750°C has been studied. The crystal structure of Ti2Cu has been detevnlined as tetragonal and when expressed as face-centered tetragonal, a = 4.164, c = 3.611 A, and c/a = 0.867. TITANIUM systems in which ß-titanium decomposes eutectoidally into a and a compound rather readily are known as active eutectoid systems. Recently in active eutectoid alloys based on the Ti-Cu system, and containing additionally A1 and Zr, it has been found that zirconium may produce both moderate weakening and marked strengthening at elevated temperatures.' In order to obtain some insight into the behavior of zirconium, an attempt was made to determine whether compounds of the type Tix Zr and TixZryCu exist. Only results of the Ti-Zr-Cu studies are reported here since data on Ti-Zr alloys will be presented in a separate publication. EXPERIMENTAL PROCEDURE Alloys were nonconsumably arc melted in argon atmosphere as 15-g buttons, prepared from materials of the following purities: Bureau of Mines electrolytic Ti — Bhn 63 OFHC copper Reactor Grade Zirconium Bhn .C 150 Prior to alloy preparation the electrolytic titanium was premelted to avoid excessive spattering of the charges during melting. The weight losses during melting did not exceed 1 pct of the total weight of the charge. The alloys prepared are listed in Table I together with analyzed compositions. in cases where they were determined. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. About 1 to 2 sec are required to remove the capsule from the furnace, drop it into the iced brine and break it. Because of the insulation effect of the quartz, this delay in quenching should not produce a large drop in temperature. In many instances, no difference or little difference has been detected between the same specimen quartz capsule quenched or directly quenched in vacuum by an impinging stream of water.' Ti-Cu-Zr alloys were homogenized for 48 hr at 825°C prior to annealing at 750°C. Annealing for 5 days at 750°C produced the same results as 11 days at temperature and it was therefore assumed that 5 days was sufficient to establish equilibrium. Titanium-copper alloys were homogenized for 40 hr at 900°C prior to heat treatment for 6 days at 750°C. Specimens for metallographic examination were electropolished and etched with the following solution:

Jan 1, 1962