Search Documents

By E. M. Kalar, I. Iwasaki, J. D. Zetterstrom

Several methods of removing fatty acid coatings from iron ore flotation concentrates were tested both on a Mesabi oxidized iron ore and on a magnetic taconite concentrate, and their effects on the duplex flotation process and on pelletizing were compared. Either acid or alkali alone could not remove the coatings, but a combination of such reagents as lime and quebracho, calcium chloride and pyrophosphate, or sulfuric acid and an organic acid (oxalic, malonic, or citric acid) was quite effective. The use of activated carbon was found to be particularly promising. The removal of fatty acid coatings from iron ores is of much practical interest when a pelletizing process is being considered for a concentrate floated with a fatty acid collector or when a duplex flotation process is being considered for upgrading an oxidized iron ore. A duplex flotation process is a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process is being used in the Florida phosphate fields.' Although in northern Michigan mills fatty acid flotation concentrates have been pelletized successfully, at other locations fatty acid coatings on iron flotation concentrates have proved so undesirable in the agglomeration operation that other methods of concentration had to be sought.' Since fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates, a combination of reagents, such as lime and quebracho,3 lime and alkali phosphate,4 or sulfuric acid and oxalic acid,' has been proposed. It was also thought that activated carbon might be effective in removing fatty acid coatings due to its high adsorptive capacity. Activated carbon, with its enormous surface per unit of volume, is well known for its exceptional efficiency in removing organic pollutants from industrial effluents. This article presents the practical aspects of the above methods when they are applied to the duplex flotation process and to the pelletizing of iron flotation concentrates. The article also includes a preliminary investigation of the common parameters involved in the depressant activity of the reagents. EXPERIMENTAL WORK Initially, the experimental work was directed towards the optimization of each method for the removal of hydrophobic coatings from iron oxide surfaces floated with fatty acids. Subsequently, the methods thus optimized were tested in the duplex flotation process with an oxidized iron ore and in the pelletizing process with a magnetic taconite concentrate. Preliminary Flotation Tests: Although the three types of chemical treatment reported in the literature were briefly investigated for the purpose of comparison, major emphasis was placed during the preliminary flotation tests on the use of activated carbon because it was thought to have certain advantages over the chemical methods. LIME AND QUEBRACHO - To obtain a flotation concentrate for optimizing the lime and quebracho method of fatty acid removal, the magnetic taconite concentrate was used. The concentrate had a size consist of 90% passing 325 mesh and analyzed 64.5% iron. After a few preliminary tests the fatty acid flotation procedure with the magnetic taconite concentrate was standardized as follows. A 1200-g sample of the magnetic concentrate was pulped in a Fagergren laboratoy flotation cell to 40% solids, conditioned with 0.5 lb of soda ash per ton for 2 min, and then further conditioned with 1.0 lb of Acintol FA-2 per ton for 2 min. After 5 min of flotation, recovery was nearly complete, averaging 98.6% of the weight and 98.7% of the iron. The cell product, which amounted to 1.4% by weight and analyzed 63.2% iron, consisted mainly of relatively coarse middling particles. Since the repro-ducibility of the flotation concentrates produced by this procedure was vey high, the same procedure was used to prepare fatty acid concentrates for each of the six tests of the lime and quebracho method. To test the removal of the fatty acid from the magnetite surfaces by the lime and quebracho method, a fatty acid froth product was returned to the flotation cell, repulped by 30 sec of agitation, and then con-

Jan 1, 1968

An Outline Classification of Mining Systems for Ore and Coal. See COAL Progress at the Homestake Mine. By Guy N. BJORGE. (Min. & Met., June, 247. 4400 words.) Homestake's mining methods today are controlled to a con¬siderable extent by that which has been done in the past. The two main operating shafts were begun m 1878 and 1896 respectively, so that the location of shafts, loca¬tions of all the drifts on the upper levels, and a great deal of stoping was done before any of those now connected with the mine had anything to do with it In this paper is described the general plan of development. A table shows percentage of total production mined by the different methods in recent years. Average daily produc¬tion for several years now has been about 3850 tons milled. With the present schedule of 6-day operation of the mine, that means about 4450 tons a day mined This ore is treated at three plants, with respective capacities of 2000, 1200 and 600 tons The principal novelty in milling is at the largest mill where the stamps are used as crushers only, and where in the last two years a notable increase has occurred in the size of screens used A unit has been added to cyanide plant No 3 The construc¬tion of a new shaft is described, as is also the hoist building The company operates its own lumber and timber department It has a well equipped hospital Housing at Lead is an individual matter. Rejuvenating the Golden Chariot Property in Idaho. By R. S. MCCLELLAN (Min. & Met, November, 443. 2300 words) An effort to rejuvenate the Golden Chariot group of properties near Silver City is now being carried on by the John Hays

Jan 1, 1935

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,'~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro'~ suggested that the strain E can be deduced

Jan 1, 1970

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere' that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By A. G. Guy

Thermodynamic activity rather than chemical composition is basic to the analysis of diffusion. This is the essential conclusion reached by Darken1-3 and by Birchenall and Mehl.4 If so, it is reasonable to expect that diffusion calculations should be carried out using activities. This paper will illustrate a method of employing activities in analyzing interstitial diffusion. For interstitial diffusion (of carbon in iron and probably generally) the diffusion of the solvent atoms, volume changes, and other such complexities not explicitly provided for in the usual diffusion equations cause a negligible error of the order of 1 pct. Therefore it is relatively easy to test the validity of an analysis based on activities in the instance of interstitial diffusion. The mathematical treatment of the more complex substitutional diffusion could be simplified once the adequacy of the activity method had been established for substitutional diffusion. Thus the present work has the purpose not only of providing a superior analysis of interstitial diffusion but also of indicating a possible approach to the more important question of an adequate treatment of substitutional diffusion. Development of the Diffusion Equation Although activities are convenient quantities to determine experimentally, they are derived from the more fundamental fugacities.9 Possible confusion in using activities can be avoided by basing equations involving their use on the relationship, dP = -D1d/ax dt [I] where, dP = the number of grams of solute crossing one cm2 in the time dt sec. D, = the diffusion constant for use with fugacities; it is assumed to be constant at a given temperature, and has units of secs. f = the fugacity of the solute in the solid solution; the units are those of pressure, dynes per cm2. x = the distance in cm. Eq 1 can be considered to be the basic form of the first Fick Law for one-dimensional diffusion. In order to convert Eq 1 into an equation involving activities, a choice of a standard or reference fugacity, f°, must be made: then. a = f [2] where a is the activity corresponding to the fugacity f. However, the value of a is also determined by the relation, a = a\c [3] where a is the activity coefficient and c is the concentration. For a given value of a (such as a = 1) it is evident that the units used for expressing concentration will affect the numerical value of a corresponding to a given amount of carbon dissolved in y-iron. Since weight per cent concentration is so widely used, this unit will be adopted as the standard in this paper. When the value off given by Eq 2 is substituted in Eq 1, the first Fick Law becomes, dP= -D,f°dl [4] Since D,f° is constant (at a given temperature), the second form of Fick's Law can be obtained in the usual manner, -dt D'f° dx [5] where c' is the concentration in g per cm3. In terms of weight per cent concentration, c, Eq 5 becomes, dc _ 100 d2a Tt = T /f w [6] where p is the density of the solid solution and will be assumed to be constant. In order to simplify Eq6, it is necessary to consider the standard state, f°. Standard states are chosen for convenience. There appears to be one especially convenient choice for the analysis of interstitial diffusion. If the activity coefficient, a, is set equal to unity at infinite dilution of the solute, 100 then — 100D1fl° is approximately equal P to the usual diffusion constant in dilute solutions. This is true since the activity, a, in Eq 6 can be replaced by the concentration, c, with little error in an infinitely dilute solution.* Here f1° is the standard fugacity necessary to achieve this standard state. It is proposed that a diffusion constant Da' be defined, Da1=100/pD1f1° [7] where A is the metal whose diffusion is * The second derivative of a is equal to the second derivative of c in dilute solution only if -da/dr- is. zero. Although theory does not require this condition, in the systems C in Fe, and Zn in Cu, dc is in fact found to be essentially zero.

Jan 1, 1950

By L. C. Chang, T. A. Read

Diffusionless transformation in Au-Cd single crystals containing about 50 atomic pet Cd was investigated by means of X-ray analysis of the orientation relationships, electrical resistivity measurements, and motion picture studies of the movement of boundaries between the new and old phases during transformation. The nucleation of diffusionless transformation by imperfections and the generation of imperfections by diffusionless transformation were discussed. THAT connections exist between plastic deformation and diffusionless phase changes has long been recognized. Thus it is often possible to produce a diffusionless phase change in a temperature range, above that in which the change occurs spontaneously, by cold-working the initial phase. Certain aspects of the dislocation theory of the plastic deformation of crystalline solids also provide for a rather direct connection between the processes involved in plastic deformation and in diffusionless phase changes. Heidenreich and Shockleyl have pointed out that simple edge dislocations in f.c.c. metals are probably unstable, and that the more probable lattice imperfections, called extended edge dislocations, consist of two half dislocations separated by a distance of the order of magnitude of 100A. The region about two atomic planes thick between the half dislocations because of this stacking fault may be described as having the hexagonal close-packed structure. Presumably the stacking faults observed by Barrett" fter cold-working f.c.c. Cu-Si alloys resulted from the passage of such half dislocations through the lattice of the initial phase. It is now becoming clear that the development of a detailed theory of the atomic movements involved in diffusionless phase changes will require a consideration of the role played by lattice imperfections, just as such considerations are necessary to the understanding of plastic deformation mechanisms. This point of view has been recently set forth, for example, by Cohen, Machlin, and Paranjpe3 who pointed out the role which might be played by screw dislocations in nucleating diffusionless phase changes. The present paper reports on some aspects of the diffusionless phase change in single crystals of the beta phase alloy Au-Cd which serve to emphasize further the importance of lattice imperfections in diffusionless phase changes. The diffusionless phase change of Au-Cd possesses several remarkable features. One of these is that the interface between the high-temperature beta phase and the low-temperature orthorhombic phase typically moves with a low velocity, in contrast to the behavior observed in the transformation of austenite to martensite. Motion pictures of this slow interface motion have been prepared in the course of the work reported here. Another important feature of the Au-Cd transformation is the small amount of undercooling observed. The reverse transformation occurs on reheating to a temperature only 20" higher than the transformation temperature observed on cooling, and under some circumstances the hysteresis observed is substantially less than this. This narrow temperature range between transformation on heating and cooling is presumably in part a consequence of the fact that the transformation requires a lattice shear of only about 3". Finally, the orthorhombic product phase possesses unusual mechanical properties, as was first pointed out by olander' and Benedicks." After completion of the transformation on cooling the specimen can be severely deformed, yet on the release of load it springs back to its original shape in a rubber-like manner. Explanation of this phenomenon will require an understanding of the lattice imperfections in the orthorhombic structure and, correspondingly, of those in the initial body-centered cubic structure. Single crystals of Au-Cd alloy containing 47.5 and 49.0 atomic pct Cd were prepared from fine gold (99.95 pct purity) and chemically pure cadmium (99.99 pct purity) by melting the alloy in an evacuated and sealed fused quartz tubing and growing into single-crystal form by the Bridgman method. The Au-Cd alloy containing 47.5 atomic pct Cd undergoes a diffusionless transformation from an ordered body-centered cubic structure to an orthorhombic structure when it is cooled to about 60°C, while the reverse transformation takes place when the alloy is heated to about 80°C, according to electrical resistivity studies. The structures of these two phases have been studied by Blander,4 reinvestigated by Bystrom and Almin.e he lines of Debye photo-gram of powdered samples of Au-Cd alloy containing 47.5 atomic pct Cd prepared in this laboratory were identified and agreed fairly well with those of

Jan 1, 1952

By B. Silliman

The regions of New Mexico referred to are in Socorro, Grant, and Dona Ana counties, and a portion of Lincoln County, embracing in the aggregate a very large area, of most of which our knowledge is as yet very fragmentary and superficial. It is only very recently that large portions of this region have been accessible. It has been full of danger from hostile bands of wandering Apaches, whose murderous raids have slain many adventurous miners and seriously prevented developments. But this evil has now been largely abated, and in many of the mining camp of this region there is no longer any danger from this cause. SOCORRO MINES. About three and a half miles back of the old Mexican town of Socorro, on the Rio Grande, chief town of the County of Socorro, are two or more large veins of heavy spar, cutting across the fat* of Socorro Mountain in a northeast and southwest direction, and dip ping at an angle of about forty degrees into the body of the mountain. These veins are in rhyolite, and, so far as could be seen in openings on the Torrence Mine, which I examined, are without any clay parting or selvage. The average thickness of the Torrence rein may be about five feet, the thickness varying from pne or two feet to thirteen feet. Upon the cleavage planes of the heavy spar occurs, in visible patches, of a waxy Iustre and gray color, silver chloride, which gives value to the vein, from a few ounces up to one hundred and twenty ounces to the ton, averaging about forty ounces, as I

Jan 1, 1882

By John Jermain Porter

THe value of any particular ore, coke, or limestone, for iron-making, depends upon its effect, first, upon the quality or value of the resultant product; and second, upon the cost of smelting. The factors under the first head are the percentages of phosphorus, manganese, and other elements, which remain in the pig-iron ; while those under the second head are the percentages of iron, carbon, or lime, the slag-forming constituents, which must be fluxed, and any other ingredients which give rise to variations in cost of fuel and flux. The first of these criteria of value is perhaps not capable of being reduced to a general formula embracing all cases, since it must vary to a great extent with market-fluctuations. For example, Bessemer pig is worth sometimes more and sometimes less than foundry-pig; and the premium paid for high manganese varies within wide limits. The second, or smelt-ing-value, however, can be expressed numerically with a fair degree of accuracy; and it is with this phase of valuation that the present paper is concerned. The utility of a means of comparing numerically the relative smeltiug-values of difierent ores, cokes, and limestones, is self-evident, although it may not have importance in Northern practice, where materials are largely standardized. On the other hand, there are, especially in the South, many furnace-managers who must use a great variety of materials of widely varying grade; and it is with special reference to this district, and in connection with the efficiency-methods which I have elsewhere proposed,' that the methods herein described were devised.

Jan 1, 1913

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By M. W. Cox, V. F. Hollister

EXPLORATION for metallic mineral deposits is carried on by those special adaptations of methods which the explorer believes will yield most economically or satisfactorily the particular answer sought. In this project the usual methods of geologic observation, recording, and interpretation, when combined with magnetic geophysical methods and geochemical soil sampling, led to disclosures of appreciable zinc mineralization where none was visible in surface exposure. Since 1945 considerable work has been done with geochemical prospecting methods, chiefly in determining the presence and distribution of various elements existing in minor amounts in rocks, soil, vegetation or waters of mineralized areas. Such work, in which the U. S. Geological Survey has taken the lead, finds a ready place in the field repertoire of the exploration geologist as a supplement, not a substitute, for other methods. The Chollet project was carried out in 1951 by the American Smelting & Refining Co. near its Van Stone mine in northern Stevens County, Wash., in the area shown in Fig. 1. The Van Stone mine is located in the Onion Creek drainage of the Selkirk Mountains, midway between the towns of Colville and Northport, Wash., and some twenty airline miles west of the Metaline mining district. Its zinc-lead orebodies, currently yielding about 1000 tpd of ore, occur as bedding replacement deposits in the middle Cambrian Metaline formation near an intrusive granodiorite contact. The target of exploration at the Chollet prospect was a similar geologic environment along the intrusive contact about 5 miles west of the mine. Geographic Setting The Chollet ground covers a north-facing slope at 3000 to 4000-ft elevation. Second-growth jack pine and tamarack with some hemlock and yellow pine make a thick forest cover. A heavy under-forest of alder, willow, and lesser shrubs occupies the draws, see Fig. 2. Grassy slopes appear at higher elevations. The lower slopes are underlain by a thick blanket of glacial till and alluvium so that outcrops are scarce; however, perhaps 50 pct rock exposure prevails at higher elevations. This part of northern Washington annually receives about 25 in. of precipitation, which largely falls as snow in the winter months. Summers are dry with occasional rainy periods. General Geology The Van Stone mine and the Chollet prospect lie along the southern margin of a westerly extending lobe of the Kaniksu batholith, one of the series of granodioritic masses that are intrusive into Cretaceous and older rocks in northern Washington and southern British Columbia. The margin is composed of complexly deformed Paleozoic sediments ranging in age from the lower Cambrian Maitlen phyllite on the east, through middle Cambrian Metaline formation (limestone and dolomite), to Ordovician Ledbetter slate on the west. In general the formations strike N10 to 50E and dip steeply northwestward, although dip reversals and minor folding occur. This general rock distribution is shown on Fig. 3. In this area the Metaline formation, which is the host rock for mineralization, appears to be of about 4000-ft thickness that can be conveniently divided into the same three units defined by Park and Cannon' for the Metaline area. The basal part consists of 1000 ft of interbedded white limestone, argillaceous limestone, and gray silty argillite. The middle part, approximately 1500 ft thick, consists of fine-grained black, gray, and white dolomite. This unit also contains minor interbedded limestone. The upper part is a gray massive limestone about 1500 ft thick that grades upward into slaty limestone and slate capped locally by a thin black jas-peroidal dolomite which is either the uppermost member of the Metaline formation or the basal member of the overlying Ledbetter (Ordovician)

Jan 1, 1956

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,' but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick's law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

Twelve Directors, the Secretary, and ten guests were present. It was unanimously resolved that the sense of this body is that the name of the Institute should be changed to American Institute of Mining and Metallurgical Engineers. Messrs. J. W. Richards and Bradley Stoughton were appointed a committee to formulate the necessary steps for bringing the matter to a vote. The committee in charge of the New York meeting, with Allen Rogers, Chairman, was appointed. The rules of the American Engineering Standards Committee were approved. The Bulletin was presented to the Springfield Arsenal. The sum of $250 was appropriated to the Southern California Section. The By-laws were changed to increase the Secretary's cash from $500 to $1000. The report of the Treasurer was accepted. Sixty-eight members, thirteen associates, and forty-eight junior associates were elected. Four members were reinstated. The resignations of seven members were accepted. Thirteen members on active duty at the front had their dues remitted. Upon the recommendation of the Finance Committee, it was resolved that the clues of any members who have attained the age of seventy (70) years and have been members for a continuous period of at least thirty (30) years shall be remitted.

Jan 7, 1918

By L. S. Panyity

The question of natural-gas supply is receiving careful consideration in many parts of the country, as in the winter months it is quite a problem to have on hand sufficient gas to satisfy the demand. Increasing the output of wells by the application of vacuum has been tried with various results and large companies have attempted to keep up the supply with gas compressors. The possibility of storing natural gas in the sands of exhausted gas pools has been tried in a few instances with satisfactory results. This method may prove of practical value in solving the problem, especially in the case of towns that formerly obtained gas from their immediate vicinity, but now must search for new pools. Town Plant Regulator High Pressure Line Exhausted Gas Field used for Storage Producing Gas Field FIG. 1. In all cases, only part of the available supply is utilized during the warns weather, so that many wells are shut-in, yet during the winter months, the supply is not sufficient even with all the wells on the line; in such cases it would be of great value if a large volume of stored gas were on hand, obtained through wells that would have been standing idle during the summer.

Jan 1, 1919

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By J. L. Jernegan

In this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two windfurnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By James B. Macelwane

THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these 'fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the. January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1952

THE Institute assembled in the Hall of the Boston Natural History Society on Tuesday evening. Dr. T. Sterry Hunt, of the Boston Institute of Technology, after a brief address of welcome to the Institute, read an introductory paper on the Geognostical History of the Metals. President Raymond responded to the welcome of Dr. Hunt. The following names were then presented to the Institute, with the recommendation of the Council, for election: Adams, J. M., . . . . . . Silver City, Idaho. Daggett, Ellsworth,. . . . . Salt Lake City, Utah. Geist, Alfred W., . . . . . Boston, Mass. Hays, Dr. S. Dana, . . . . . Boston, Mass. Heinrich, Oswald J., . . . . Midlothian, Va. Johnson, J., . . . . . . Braidwood, Ill. Leckie, Robert G., . . . . . Actonvale, Canada. Lyman, Edward, . . . . ' . Troy, N. Y. Maltby, William, . . . . . Braidwood, Ill. Nichols, Lyman, Jr., . . . . Bbton, Mass. Ordway, Prof. J. M., . . . . Boston, Muss. Rand, Theodore D , . . . . . Philadelphia, Pa. Richards, Prof. Robert H., . . . Boston, Mass. Roclrwell, Prof. Alfred P., . . . Boston, Mass. Roepper, Charles W ., . . . . Bethlehem, Pa. Schulz, A. von, . . . . . Central City, Colorado. Singer, William F., . . . . Pittsburgh, Pa. Spillsbury, E. G., . . . . . New York. Wells, Calvin, . . . . . . Pittsburgh, Pa. The session concluded with the reading and discussion of a paper, by Henry Engelmann, On the Mines and Ores of the Little Cottonwood Canyon, Utah. The second session was held on Wednesday morning, when the following papers were presented : On the Midlothian Coal Mines, by Oswald J. Heinrich. On the Probable Existence of Microscopic Diamonds in California, by Prof. Benjamin Silliman.

By Hubert O. DeBeck

The following descriptions and explanations apply specifically to the use of the Hotchkiss Superdip, but there are no apparent reasons why they should not apply to any magnetometer. This paper is a product of work in the practical field for several years with the Hotchkiss magnetometer, mostly on mineral deposits in the southeastern United States. The paper describes the result of an attempt to develop a practical and economical field method that approaches, as nearly as possible, the utmost accuracy of which the magnetometer is capable. As there are many published descriptions of various magnetometers and magnetic methods, it would be superfluous to describe such instruments here, but a limited bibliography on the Hotchkiss and Askania magnetometers is appended. The Hotchkiss and the vertical Askania magnetometers have, respectively, maximum sensitivities of approximately 5 and 30 gamma per instrument scale division. Purpose of New Method The purpose of the method described in the following paragraphs is to eliminate, as far as possible, all corrections of field data that cause complexities and inaccuracies in the results of magnetometer surveys. Magnetometer field observations must be corrected for periodic variations in the intensity of the earth's magnetic field, as well as for temperature variations, both of which take place during the course of a day. These variations do not seriously handicap magnetometer work on highly magnetic deposits, but it is impossible to obtain accurate results, by the conventional methods in use today, over weakly magnetic or diamagnetic deposits. This is due to the physical inability to obtain by such methods sufficiently accurate data in the field to make dependable corrections. The magnitude of the necessary corrections of field observations frequently exceeds the magnitude of local magnetic anomalies obtained over various types of mineral deposits. Therefore if these corrections are neglected or made on the basis of inaccurate data, the entire magnetic picture of the area concerned is at least distorted, and perhaps destroyed altogethcr.

Jan 1, 1934

Attention! Engineers! Geologists! Here is your Opportunity to be of Professional Service The war has interrupted the supply of many minerals, which were normally imported. In view of present transportation conditions, a serious shortage exists in certain materials and will soon develop in others. Some immediate action is imperative. The first thing is to take a careful inventory of American resources. We must know where the ore deposits are, what has hitherto hindered their utilization, what methods must be used, and what equipment will be needed if an emergency demands their rapid development. Many properties must be re-examined from a new point of view, that of present necessity rather than of normal profit. When the shortage is realized, the preliminary steps for relief should have been completed. It is a necessary and patriotic form of mineral insurance. Will you have a part in it? Do not forget that these are war times, and that what may have been valueless a year ago may be a "life-saver" now; an abandoned copper prospect of 1913 might make a successful pyrite mine in 1917. We are fighting an autocratic enemy who knows his resources to the last pound, and uses them with most efficient organization. We have no Kaiser, so each of us must do his share to put our Government in the same situation. The Government needs your facts.

Jan 8, 1917