Search Documents

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.' A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be' used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

By K. R. Waugh, Barbara S. Brown, D. W. James

AN electronic data-processing system is described which permits rapid, accurate, low-cost processing of strain-dependent damping data utilizing equipment normally available within the service facilities of most large laboratories. On analyzing the record of a stress-dependent damping test, the operator usually measures the double amplitudes at several points on the decay curve. The logarithmic decrement is then calculated for decay between consecutive amplitudes. These values of 6 are plotted against the corresponding maximum surface shear stress, T, which is proportional to the average of the two amplitudes between which is calculated: where d is the specimen diameter. The period of the vibration is not necessarily constant during decay; thus, each cycle must be counted. A decay curve may extend to, perhaps, 1000 cycles, and at least two curves are always obtained for each specimen or set of conditions. It can, therefore, be seen that manual analysis of decay curves is both tedious and costly in terms of man-hours. Furthermore, the resolution of the record is often such that accurate measurement of amplitude is extremely dif-

Jan 1, 1969

By C. H. Curtis

The valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 4, 1950

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By P. W. Bridgman

During the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer lagers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 1, 1922

By P. W. Bridgman

During the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer lagers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 1, 1922

By J. D. Gill

Restriction programs in important raw-materials industries in foreign countries have been abandoned after lengthy trials. Presumably, failure has been a logical consequence of the attainment of objectives of the restrictive schemes in the early periods of their administration in defiance of economic law. In general, the chief objective has been the elevation of prices of the products of these industries. More conservative plans have sought the maintenance of a price structure that was in jeopardy at the time restriction was initiated. The course of the administrat'ion of restrictive measures can be traced by the result's of restriction, viz.: the creation or maintenance of highly profitable prices; the over-expansion of productive facilities; the accumulation of inventory; and finally, by the collapse of the price structure, which invariably has led to abandonment of the restrictive scheme. The theory and practice of restriction as applied to industries that have tried it are too well known to need detailing here. Restraint of Production of Crude Oil Regardless of the record of the catastrophic outcomes of restrictive measures in other industries, our industry has not been deterred from attempting restriction of crude-oil production. The assumed bases for success of our restrictive plan are clear. They follow from the fact that the physical characteristics of the petroleum industry differ from those of other industries that have tried restriction. Its raw material is a highly essential substance, a natural, exhaustible resource. The extent of its reserves is unknown, a fact that arouses the cooperative spirit of conservationists. At no time before the inauguration of restriction had its developed reserves been sufficient to supply more than the requirements for a few months without the help of new drillings. To a considerable extent its discovery involves the element of chance. Its economic production seems to require an unnatural relationship; namely, cooperation among competitors, because it is a fugitive resource, capable of moving from under one owner's property to underlie another's. Thus its recovery presents intricate legal questions concerning property rights.

Jan 1, 1934

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

THROUGH the courtesy of the Southern Appala-chian Coal Operators' Association, a joint meeting of the Southern Appalachian Efficiency Associa-tion and local members of the A. I. M. E. and A. S. M. E. was held at Knoxville, Tenn., on Nov. 12. In introduc-ing the subject and stating the object of the meeting, H. Foster Bain, speaking for the. Institute members, said "Shoveling coal is the largest job of hand labor re-maining in this country, with the exception of the mis-cellaneous work on the farms, and even there nearly all the big jobs are now performed with the help of machines. The men in the coal mines, by hand labor, dig, each year, more cubic yards than were taken out of the Panama Canal. It has been a natural ambition of engineers, operators and men alike to follow here the characteristic lead of American industry and to substi-tute as far as possible the work of machines for the work of men; to promote the latter to the position of con-trolling and directing mechanical power rather than being themselves the machines that lift the coal from the floor of the room into the mine car. "Handling materials is one of the regular jobs of mechanical engineers, and the American Society of Me-chanical Engineers maintains a Materials Handling Division for discussion of the technical problems con-cerned. Having in mind the excellent results that had flowed from application of mechanical power and de-vices to these problems in factories, port terminals, warehouses, and other above-ground plants, the Me-chanical Engineers began to consider the possibility of introducing similar methods underground. Individual-ly, many were called upon to design, erect and operate machines for such use and at once they found them-selves faced by many novel conditions and difficulties. The Division thereupon planned a general meeting in New York in March, 1926, for consideration of problems and progress in this field. The Mining Engineers. and representative coal operators were invited to attend and

Jan 12, 1927

By K. P. Chong

Introduction One of the requirements of processing oil shale or other energy bearing rocks is to optimize particle sizes and permeability distributions in fragmentations as indicated by Hommert (1984). Basic to the understanding and planning of in situ fragmentation and ex situ mining of oil shale are the mechanical properties. During the past six years, an innovative and unique program was established by Chong et al. (1979, 1980a, 1980b, 1982a, 1982b) that developed an efficient methodology for standardized and simplified mechanical testing of the western oil shale. The experiments include precise, representative, and duplicable sample preparation; uniaxial static compression testing; "modified" split cylinder testing; uniaxial creep and relaxation testing under extended periods of time; dynamic testing with varying strain rates; and 3-D constitutive relationships. However, as far as the fracture mechanics is concerned, as Edl (1980) pointed out, there is still a lack of understanding "of the fundamental explosive rock breakage mechanisms," which "has necessitated extensive reliance on very costly empirical approaches." Fracture mechanics of rocks and oil shale (Costin, 1981; Schmidt, 1977; Abou-Sayed, 1977; and Barker, 1977) has been based on conventional fracture mechanics using regular notched samples with limited variations of oil yields and assuming the material to be isotropic and elastic (Kobayashi, 1975; Caddell, 1980). A cylindrical double cantilever beam (DCB) specimen with a "V" slot, known as a short rod specimen, has been used by Barker (1977) to determine fracture toughness of rock materials. The inherent geometric stability of the reinforced DCB specimen makes it suitable to be used with all brittle materials. Due to its remarkable stability for the initial crack growth, the DCB specimen can be used for dynamic fracture toughness testing as well. This specimen is more suitable for the evaluation of fracture toughness at high strain rates than most other fracture specimens. However, Barker's DCB specimen is not very well adaptable for short cores or layered rocks since the specimen contains numerous layers (say in a 100-mm (4-in.) long specimen), and the rock properties change from layer to layer. Schmidt (1977) studied the fracture mechanics of oil shale with two oil yields, using notched beams. Using several independent established testing methods, Costin (1981) pioneered the investigation of the static

Jan 1, 1986

By G. S. Cole, H. Biloni, G. F. Bolling

An experimental investigation of sovlze low .melting point alloys sJtows that a substvucture of isolated depressions can be the first manvestation of constitutional supercooling on solid-liquid interjaces veuealed by decanting. Electron-tni cvop vobe and wletallo gvaplic esanzinations, in tlze bulk belzind the interjace, oj the segregation associated with these isolated areas substantiate tlzei&apos;v depressed nature, since a solute of ko < 1 is enriched, and a solute of ko > 1 depleted. In contrast, the pox structuve, a set of projections often veported in the literature, leaves no trace oj. segvegation. These obserl;atims, accovlrpanied by a brief review of recent literature, point to inconsistencies between experirrental obsevvation and the idea that the fornzation of a projection is a causal step in the development of a cellular substructure. An argument is presented to show instead how it is plausible for substantial depvessiom to form in the pvesence of constitutional supercooling at dislocations threading the solid-liquid interjace. THE development of constitutional supercooling during growth from the melt leads to the formation of the cellular solidification substructure. This well-founded association between structure and instability has been basic in understanding cellular substructure and micro segregation; however, the initial formation of structure seems unclear. Rutter and Chalmers,&apos; in definitive experiments and theory, noted that in the presence of constitutional a planar interface might break down: "resulting in the formation of a small projection on an initially plane or uniformly curved interface." That is, the breakdown from a planar to a cellular interface was implied to be initiated via a projection into the unstable liquid. Later, Walton et (11. found that a structure of isolated projections, termed "pox", appeared at solid-liquid interfaces decanted under growth conditions near the onset of constitutional supercooling; the pox were taken as the indication of the instability promoted by the supercooling. Tiller and Rutter4 in their extensive work studied the shape transitions at decanted interfaces which were generally observed to proceed as— pox, "irregular cells", elongated cells, regular (hexagonal) cells, and so forth. The pox varied in size from lo-&apos; to 1CT4 cm, and tended to disappear as cells increased in number and regularity, but as noted,4 the first real array of cells did not seem to be a development from the pox. In fact these authors implied a lack of connection because they stated that the pox are denser on "irregular cells", and as cell boundaries increase in number (i.e., the cells become smaller) there is less need for the pox which do dis- appear. Thereafter, most authors dealing with either experiment or theory have accepted the reality of pox and have used them as a criterion for the onset of constitutional supercooling. In contrast, Spittle, Hunt, and smiths have now suggested that pox are irrelevant artifacts comprised of such things as entrapped oxide. This proposal invokes the observations of weinberg6 and chadwick7 each of whom have shown that the act of decanting leaves a residual liquid on a decanted interface; the remnant solid layer of the order 10 p may thus contain particles that might have been transported from the external surfaces, or elsewhere, during decanting. With the incentive of this suggestion,= some further experiments and a reexamination of the literature have been conducted, in order to question the validity of pox as evidence of an instability and to examine the initial development of the cellular substructure. 1) EXPERIMENTS Single crystals of zone-refined tin (-99.9999 pct) were grown from the melt in a controlled fashion with various, small concentration additions of lead and antimony, for which ko < 1 and > 1, respectively. The crystals were decanted at conditions near the onset of constitutional supercooling and were thus appropriate for observation of slight perturbations. It was possible to observe two types of small departure from smooth or "planar" interfaces in both cases of lead or antimony additions. Some were projections and others, if in regular array of any type, were depressions. The crystals were etched with suitable reagents progressively dissolving the decanted interface surface; projections left no record, but depressions were continuously associated with spotlike areas contrasting with the rest of the interface. Traverses were made with the beam of an electron microprobe across the regions of contrast; with lead addition the persistent spots were lead-rich, and with antimony addition the persistent spots were antimony-poor. This is consistent only with a dominant role for depressions, because if the projections had left spots but were incorrectly catalogued, a reversed observation should have been made; that is, the Pb(ko < 1) should have been depleted and the Sb(ko > 1) enriched. In the work of Cole and inegard, and elewhere, regular arrays of structure associated with the initial stage of instability have been shown, in photographs and represented as pox or projections. We believe this to be erroneous, by inference, since whenever a regular array was observed, in the present examination, it consisted of depressions, regardless of the nature of the solute, ko 1. Fig. 1 is reproduced8 as an ideal example of the possible optical illusion involved; the observer can satisfy himself from the distribution of illuminated areas that the markings are depressions. Fig. 2 from the present investigation is an interference photograph of an interface similar to that in Fig.

Jan 1, 1967

THE 127th meeting of the Institute was held in New York, Feb. 19 to 22, 1923. In addition to the usual large volume of technical matters under consideration, the meeting was particularly noteworthy for the amount of attention given to its business session; the convention of local section representatives also was full of interest. The total registration was 1201. The annual business meeting on Feb. 20, President Dwight presiding, was attended by 125 members, who listened with marked attention to the reports and addresses of the several officers. The chairman departed from the stipulated order of business in order to allow more time for the presentation of remarks on the state of Institute affairs. The previously pub-lished reports of the officers were accepted, as printed. On the report of the tellers, the following officers were declared elected: E. P. Mathewson, Director and President-District 0 T. T. Brewster, Director and Vice-president-District 6 Frank M. Smith, Director and Vice-president-District 11 W. H. Aldridge, Director-District 0 G. H. Clevenger, Director-District 1 A. N. Diehl, Director-District 3 Reno H. Sales, Director-District 7 Seeley W. Mudd, Director-District 10

Jan 3, 1923

By G. P. Conard, E. H. Rennhack

The creep behavior of hot-rolled, hypoeutectic Zn-Ti alloys was investigated in the temperature range from 0.43 to 0.53 TM. Secondary flow was found to originate primarily from strain-induced gvain growth where grain boundary )nigvation served to relieve the strain energy of distortion introduced by slip, grain boundary sliding, and subgvain formation. The extent to which this recovery mechanism operated was determined by the ratio of grain width to the spacing between planar fibers of TiZn,, compound particles generated in these alloys during rolling. When this ratio was unity, creep resistance demonstrated a marked improvement. In this condition, which was fulfilled by annealing following rolling, structural stability was enhanced with decreasing grain size below the equicohesive temperature (-0.5Tm), while the reverse was true above this temperature. TITANIUM concentrations approaching the eutectic composition of 0.23 wt pctl have been shown to promote a significant increase in the creep resistance of rolled zinc,2 The alloying effect created with titanium is somewhat unique; a structure closely resembling that of a fiber-reinforced metal composite can be developed which selectively modifies creep strength in preference to other mechanical properties. In an earlier investigation,~ the present authors found that, while the fiber network, composed of individual TiZn,, compound particles, had a distinct influence on rolled texture, the crystallographic variations produced were of minor importance with respect to creep. Rather, creep resistance seemingly increased when the grain size appeared to coincide with the in-terfiber spacing. The work described here was undertaken to explore this effect in greater detail. EXPERIMENTAL PROCEDURE Three zinc-base alloys containing 0.05, 0.12, and 0.16 wt pct Ti were prepared from CP zinc and iodide titanium in the form of 4 by 2 by f in. chill-cast ingots. The melting and casting procedures for these alloys have been detailed el~ewhere.~ Individual ingots of each alloy were hot-rolled at 200°C (392°F) to total reductions of 10, 25, 50, 75, and 90 pct in from one to five passes, respectively, employing a 10-min reheat prior to each rolling pass. With grain, tensile-type creep specimens with a 1-in.-long, -in.-wide gage section were machined from the rolled strips for test purposes. Annealing studies to explore the influence of grain size on secondary creep flow were carried out at 400°C (752°F) in argon for times extending up to 60 min. The grain-size effect was evaluated in terms of average grain width and length values statistically derived from lineal intersection measurements.4 A similar method was applied in establishing the average interfiber spacing, i.e., average perpendicular distance between adjacent planar fibers. The creep characteristics of the alloys were investigated by means of constant-load and constant-stress creep tests. The former tests were conducted at 25°C (77°F) under an initial stress of 10,000 psi, while the latter were performed in the range from 25°C (77°F) to 90°C (194°F) at stress levels varying from 8000 to 22,000 psi. Total specimen strain, as determined with Budd HE-1161-B strain gages, was in excess of 0.10. Maintenance of constant stress was achieved through periodic load reductions made at 0.01 strain intervals to compensate for the attendant incremental reduction in specimen cross-sectional area. The maximum indicated error in the applied stress at these strain intervals was less than 3.0 pct. RESULTS AND DISCUSSION Constant-Load Creep. In an effort to clarify the in-terrelation between interfiber spacing and grain size with respect to the creep resistance of the Zn-Ti alloys, their separate effects on secondary creep rate were determined as a function of titanium content and rolling reduction. These results are set forth in Figs. 1 and 2, respectively. The average grain diameter plotted in Fig. 2 was resolved from average grain width and length values. No data are presented for reductions of less than 50 pct because of the inability to obtain consistent measurements on these strips. The curves of Fig. 1 indicated that, for a given titanium content, a decrease in interfiber spacing, as produced with increasing reduction, promoted a decrease in creep rate. Depending on titanium content, however, wide variations in creep rate occurred at the same interfiber spacing suggesting that interfiber spacing, by itself, has little or no influence on creep resistance. Grain size, on the other hand, decreased progressively with both increasing rolling reduction and titanium content, the effect of which led to a pronounced decrease in creep rate, particularly when the average grain diameter became smaller than 3.0 x 10"4 in., Fig. 2. The continuity of this relationship tended to support the view that grain size rather than interfiber spacing was predominant in controlling secondary creep. Annealing Effect. The observed dependence of creep flow on grain size suggested that a further contribution to creep resistance would result when the alloys were annealed to effect a coincidence between grain width and interfiber spacing, see Fig. 3(b). ~eiides creating an immediate barrier to grain boundary movement, annealing offered the possibility of providing increased structural stability by eliminating many high-energy, mobile grain boundaries.= To test this hypothesis, specimens from the Zn-0.16 Ti strips reduced 75 and

Jan 1, 1967

By Roger K. Clifford, Gary W. Hudiburgh

The amine flotation of feldspar from a magnetite concentrate produced at a domestic concentrator was investigated using zeta potential measurements, Hallimond tube flotation tests, and laboratory-scale flotation tests. The point of zero charge of six feldspars (microcline, orthoclase, albite, anorthite, anorthoclase, and oligoclase) range from pH 1.4 to 2.5. Hallimond tube flotation tests using amine flotation reagents were performed on these feldspars and on gangue material (quartz, albite, and microcline) from the magnetite concentrating plant. Laboratory-scale (623 g and 2500 g) flotation tests were performed on the magnetite concentrate to float the feldspar. The effects of three different collectors, two levels of collector concentration, three pH levels, starch, HF acid and regrind were investigated.

Jan 1, 1977

By A. Mitchell, M. Etienne

VARIOUS&apos;-3 reports on the electroslag remelting process refer to the "thin skin of slag" existing around the slag pool and the solidifying ingot, but none considers the various mechanisms by which this layer forms and thus influences the surface quality of the ingot. A vertical section4,5 of the Cao-CaF2-Al2O3 diagram is shown in Fig. 1 between CaF2 and 6Al2.CaO3 From this, it is seen that a typical "70:30" CaF2:A1a3 slag will solidify to produce 6Al2O3.CaO primary phase in a eutectic matrix. The commercial slags contain sufficient CaO to produce* this composition by both the

Jan 1, 1969

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

A new apparatus termed a "distribution analyzer" is introduced to ascertain the optimum conditions of electrostatic separation of minerals. It was found that with similar surface condition, testing environment and a constant feed rate of not higher than one layer of particles fed on the grounded roll of the separator, the behavior of each component mineral in a synthetic mixture or ore is roughly similar to that of the same mineral when tested alone.

Jan 3, 1950

By John Wulff, Richard P. Seelig

THE importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by sub- sequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be con- trolled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper. In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshin1 on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin1 and Rakovski.2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,1 based on a hydro- dynamic analogy, however, leads to but another way of plotting density and pres- sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. DENSITY GRADIENTS IN COMPACTS The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By S. Suphi Yavasca, A. M. Gaudin

THIS paper is intended as a contribution to our knowledge of the mechanism of comminution and of the work of crushing. In a previous paper&apos; it was shown that with quartz comminution proceeds as follows I. The size distribution of broken fragments made by a single fracture is such that the new surface on each grade is the same. 2. Multiple fracturing results in a size distribution such that in the fine sizes the surface per grade is the same in every grade; in coarse sizes the surface per grade decreases gradually with increasing size. In that paper it was mentioned that determinations on minerals other than quartz were in course of completion in order to establish the generality of these observations. In this paper, condensed data2 are presented for galena, pyrite and glass. Galena and pyrite are crystalline material and glass is noncrystalline. Galena has excellent cubic cleavage. Pyrite, although cubical, does not have marked cleavage. Quartz, on which the original determinations were made, does not cleave and although crystalline (hexagonal) breaks conchoidally. Glass breaks much like quartz. It is apparent, therefore, that the minerals selected represent some range in character of the solid without covering all possible types. GLASS Fifteen glass marbles were crushed individually in the pendulum crusher described in the preceding paper,1 then subjected to careful screening for 30 min. Six sized fractions were selected and cleaned in a hot 0.12 N solution of hydrochloric acid, washed with distilled water and dried on a hot plate. This was followed by an examination with a binocular microscope, to remove foreign matters not eliminated in cleaning as well as to eliminate "compacts" of fine particles. These compacts are groups of fine iragments that seem to be mechanically stuck together as a result of localized compacting during the comminution operation. The presence and the abundance of these compacts may be related to the amount and direction of the forces applied in different crushing devices. Since, properly, such compacts should be entirely eliminated in the sizing analyses, it is necessary to remove them to the last before making surface determinations on sized fractions. For example, with a - 28 + 35-mesh glass the surface areas of two samples, one cleaned with acid and under the binocular, the other only washed, were 102 and 172 sq. cm. per gram, respectively. Examination of the samples under an Ultropak microscope showed that washing alone failed to remove the compacts and also that it fails to remove certain fine dusts attached to the particles. Cleaning with acid loosens the fine dusts and

Jan 1, 1945

By Walter S. McKee

Discussion of the paper of WALTER S. McKEE, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2399 to 2411. J. W. RICHARDS, So. Bethlehem, Pa.-I regret that the author has overlooked the great usefulness of the electric furnace for the melting of ferromanganese in the manufacture of manganese steel. WALTER S. MCKEE, Chicago, Ill. (communication to the Secretary*)-In an article as brief as mine it was not possible to .fully cover the metallurgical field; this accounts for my not mentioning the electric furnace for the melting of ferromanganese in the manufacture of manganese steel, although the advantages of such an apparatus are fully appreciated by me. FREDERICK LAIST, + Anaconda, Mont. (communication to the Sec-retary?).-Manganese steel has proved very serviceable in our plant.. We are using manganese steel for the jaw plates on the 5-&apos; by 15-in. crushers in the concentrator instead of cast-iron jaw plates which we formerly used. The manganese steel wears five times as long as the cast iron. We are also using manganese steel in our 8- by 20-in. crushers. In our primary crushers, which are 12 by 24 in., we still use cast iron because the manganese-steel plates wore unevenly and left shoulders which caused trouble in setting up the crusher. Another reason for preferring cast iron in these crushers is that they grip the ore better on account of wearing of the rougher surface. The surface of the manganese steel becomes polished and large pieces of ore fail to be drawn in. We recently tested 8- by 16-in. manganese-steel elevator buckets working on 2-in. undersize against malleable-iron buckets and found that manganese-steel buckets lasted two and one-half times as long as the malleable-iron buckets. We use manganese-steel screen plates on our 2-in. trommels and have found that they last about five times as long as cast iron. We also used manganese-steel wheels and rails under the 20-deck round table in our slimes-treatment plant. We first used cast-iron rails and wheels and found that these wore badly at the end of two or three weeks, while the life of the manganese steel seemed to be almost indefinite; we never had occasion to change any of the manganese steel rail sections or wheels in the year and nine months that the plant was in operation.

Jan 5, 1916

By H. W. Hardings

Nearly every mining and metallurgical engineer will recall his early experience and method of producing step- or stage-reduction in preparing ore-samples for assay, in which he employecl idea, step- or stage-reduction simply because it was a self-evident fact that it would be easier to break coarse ore with a hammer than it would be to roll it back and forth under the muller, and alter having reduced it to a size easy for a rubbing or bucking division he then placed it under the muller on the bucking-board and further reduced it in proportion to the physical energy he wished to expend, which was generally the minimum to produce results. After this step in our experience me seem to have ceased to consider stage-reduction as mechanicallg essential, probably because it did not apply to individual exertion. Moreover, me did not retain the mass under the muller until it was all reduced to pass the 80-mesh assay-oftice screen, but practiced further step-reduction by screening out the fine in order that it should not interfere with subsequent work, replacing the coarse for further reduction on the bucking-board. It was many years after the bucking-board stage of metallurgical practice that we mere brought to a full realization that there was a more economical method in applying the crushing forces usually employed in metallurgical work by taking advantage of this individual experience and applying it to mechanical ends. We have made some advance to this end in bringing out the conical ball-and-pebble mill—a device which fairly well automatically adjusts power to the results obtained, mechanically repeating the bucking-board experience. In the action of the conical mill, theory is evolved from practice, rather than practice from theory, as is commonly the case.

Jan 1, 1914