Search Documents

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

Prior to any detailed discussion, I&apos;d like to say that Dr. Aplan has made direct hits on two important considerations: 1) The most demanding need in Fine Coal research is to develop improved methods of sulfur reduction. 2) The areas of particle (impurity) liberation and froth flotation hold real near-term promise as techniques for improved sulfur removal. Digressing for a moment, I thin kwe can all remember the time when the biggest problem facing coal research was simply defined - "No money!" In the mid 70&apos;s we suddenly found ourselves dealing with a product worth five to seven times the value it carried in the mid60&apos;s. All of a sudden, we&apos;re talking about a high-profile, high- value commodity. The coal industry still hasn&apos;t made the complete psychological adjustment - especially in the operating areas (prep plants included). We have a valuable material at hand which is, in&apos; many cases still being processed as though it were a two or three dollar per ton item. Simply put, I think that while the industry has made some major strides during this transition, a stronger commitment of attitude (and finances) needs to be made toward deeper definition of beneficiation work. Back to specifics - Dr. Aplan has really highlighted three areas where strong research efforts are needed. 1) Liberation processes - not limited to mechanical comminution - must be more fully studied.The industry certainly needs a better handle on value returned (improved ability to beneficiate) for dollars spent on improved liberation. 2) Flotation processes probably hold the most promise for near- term improvement in fine coal beneficiation technology. Dr. Aplan’s.

Jan 1, 1979

By K. Barron

The glass insert stressmeter, or photoelastic stressmeter, is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. The object of this study was to assess the behaviour of the meter under biaxial loads and to examine some of the problems associated with measurement and interpretation of the fringe pattern. This assessment has been carried out by comparing theoretical and laboratory behaviour of the meter. It has been shown that: a) There are certain optimum measuring points in the meter at which measurements should be made for best accuracy. The position of the points depends on the ratio, n, of the biaxial stresses. b) The meter&apos;s sensitivity can be assumed to be independent of the rock modulus E provided that the rock modulus is < 2.5 x 106 psi and not, as previous workers have assumed, if E < 5 x 106 psi. c) There are several methods of separating the principal stresses; some of these are unsatisfactory. A new method is proposed and discussed. d) The meter sensitivity decreases as the ratio of the biaxial stresses approaches unity; the accuracy thus also decreases. e) The axes of symmetry of the fringe pattern give an excellent indication of applied stress direction. f) Laboratory calibrations are in good agreement with theory. The glass insert or photoelastic stressmeter is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. This stressmeter has been described in detail.l,2 Basically it is a hollow glass cylinder that has at one end a light source and filters producing circularly polarized light. The glass cylinder and source are grouted into a borehole in rock and the face of the cylinder is viewed through a quarter wave plate and an analyser. If, after installation, a stress change occurs in the rock, then a distinct colored isochro-matic fringe pattern is seen in the meter. The fringe order at any point in the meter can be determined by counting the fringes and measuring the fractional fringe orders by the Tardy compensation method. The relation between the fringe order at any point and the applied stress change can be determined either by calculation or by calibration. The object of this study was to assess the behavior of this stressmeter under biaxial loading conditions and to examine some of the problems of interpretation of the fringe pattern. THEORY Hiramatsu et a14 have determined the stress distribution in a hollow cylindrical inclusion in an elastic host material when subject to uniaxial stress. Using this solution, the biaxial case of stress p in the x direction and stress q in the y direction (Fig. 1) can be solved by superposition. This has been done in Appendix 1. It is shown that the principal stress difference (s1 -s2) at any point (r,?) in the cylinder is given by:

Jan 1, 1965

By Allen D. Gorrison

EFFORT to develop fundamental quantitative information and improved technique in the production of petroleum has long been faced with difficulties of a particularly evasive nature, owing to a combination of circumstances. In the first place, petroleum comes from far below the ground, out of sight, so that information derived from indirect observations must be extrapolated to reservoir conditions. If one does not force the analogy too far, the petroleum engineer may be said to be somewhat in the position of the astronomer. The actual phenomena which he wishes to observe in detail appear at a place so deep in the earth?s crust that personal observations and direct experiments are impossible.

Jan 1, 1942

By J. M. W. Mackenzie

The rheological properties of aqueous solutions of several commercial flocculants were investigated using a rotating coaxial cylinder viscometer. Similarities between the pH-apparent viscosity relationship and the flocculating properties of the reagents are discussed here. Synthetic neutral polymers and polyelectrolytes are used extensively as flocculants in mining and chemical engineering operations. The action of these reagents has been interpreted as adsorption of the polymer flocculant to the mineral surface, followed by the formation of physical polymer bridges between the particles.4,5 A consequence of the bridging model is that the efficiency of a polymer flocculant depends on the degree with which the polymer is adsorbed to the mineral surface, and the extent to which the polymer molecule forms a bridge between colliding particles. The length of the polymer molecule and its orientation at the mineral surface are important in the bridging mechanism since the further the polymer segments can protrude from the mineral surface the greater the probability may be of these segments contacting another mineral particle. Linke and Booth7 have shown that, for a silica suspension, both the settling rate at a given polymer addition and the maximum settling rate obtainable increase with increasing molecular weight. The analysis of silberbergl0 has

Jan 1, 1964

By T. Lane Carter

Before describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor—that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir&apos;s wants are few. While at work Be spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Jan 1, 1909

By J. E. Johnson

The description of the machine which coilstitutes the subject of this paper is best iutroduced by a statement of the conditions which led to its construction, which may be briefly given as follows : The ore handled at the plant to be here described* is of the variety sornetimes called by those familiar with the brown ores of the South, " Mountain," as distinguished from the " Lime-

Jan 1, 1899

By Fuller, T. S.

THE number of rare or uncommon elements in use in the electrical industry nowadays is large, their application having come about through investigational work in industrial search laboratories and &apos; educational institutions. Such elements, together with those whose properties are more generally known, constitute Nature&apos;s gift to mankind and make possible the intricate devices which further our modern civilization. The&apos; quality of raiaity is one of degree, and obviously depends largely on one&apos;s point of view. From the standpoint of quantity measured in the customary units of weight and volume, the amounts of many of the elements required are extremely small, but from the of view of performing some particular function or .other in a manner more satisfactory or cheaply than can be accomplished by any other sub- stance, the use in question may be extremely important.

Jan 1, 1928

By E. G. Woodruff

The earlier struggles in petroleum geology were directed to solving the Qrigin and method of accumulation of petroleum. We are now fairly well agreed on those subjects. Most of us think that the great mass of petroleum commercially produced comes from plants or animals, or possibly from both. We are confident that the oil was not produced where it is now found but has accumulated in reservoirs of various kinds. The types of reservoirs are certainly variable but they just .as certainly follow definite geologic laws. Some of these types of reservoirs can be determined from surface study; others cannot. We know, too, that these types of reservoirs (largely structures such as anticlines, domes, and terraces) are much more widespread than the oil pools. In other words, there are many places where good sands and good structures exist but where oil is not found. It is the purpose of this paper, therefore, to attempt to analyze, from a regional standpoint, some of the conditions that control the presence or absence of oil pools and to group them in a regional way, hence the term "Petroliferous Provinces." The paper lays no claim to presenting new facts but attempts to group and classify the information that so many have expressed again and again. The essential factors for an oil field are petroleum, a reservoir material, and conditions under which the petroleum can enter the reservoir but cannot escape except through the drill holes. The paper will first discuss the source of petroleum as it occurs in definite regions, then the regional arrangement of reservoir strata, and finally the areal arrangement of structures. To have petroleum, there must be a source. Since living matter is considered the source of the petroleum, geological conditions must have been such that living organisms were abundant. Arid regions on the earth&apos;s surface have not given rise to living things in sufficient abundance to produce oil; similarly, too cold regions and saline inland lakes. The converse of this is that warm moist conditions must prevail to produce an abundance of vegetable matter. Before an area can be

Jan 1, 1921

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man&apos;s mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By John V. Beall

It is difficult to understand why they did it. It was a demonstration of total commitment which sent chills of mixed admiration and fear up and down your spine. The scene was the bodega in Section A, 2660 Level on the 12 to 8 shift. The jefe was patiently waiting for the tea leaves to settle in a large metal cup. His attention was distracted by the appearance of a miner who had a problem. The long and short of it was that the miner believed the branch raise he was driving was unsafe and he wanted the jefe to come and see it. After lunch the jefe went around. First cautiously shining his light to peer up the raise from outside the chute, he then scrambled inside and swiftly climbed the cribs to the face. No question, it was hairy; about 4 crib sets were needed to catch up to the face. The unsupported raise was slabbing. It didn&apos;t take the jefe more than a few seconds to ascertain this situation and to slide back down. As he came out of the chute, a small avalanche arrived on his heels and provided a sort of exclamation point to his order; "cerrado!" In other words, shut &apos;er down.

Jan 1, 1970

By W. A. Krivsky, R. Schuhmann

PREVIOUS papers in this series on the thermo-•t dynamics of copper-smelting systems have presented a survey of the field and an outline of the overall program: thermodynamic studies of iron silicate slags, 2-4 and thermodynamic data for simple mattes in the Cu-S system.5 Since this program was started, an excellent summary of the whole field of physical chemistry of copper smelting was published by Ruddle. The present paper represents a further step in the study of liquid mattes, and deals specifically with the Cu-Fe-S system. The importance of the Cu-Fe-S system to copper smelting is evident from the fact that these three elements constitute 90 to 99 pct of the totalweight of most commercial mattes. In copper mattes oxygen is an important fourth component. Oxygen was rigorously excluded in the work to be described in this paper. However, the behavior of oxygen in mattes was the subject of a companion research by Lander&apos; which will be described in a subsequent publication. Several studies have been made previously of phase equilibria in the Cu-Fe-S system,8-10 so that the ternary phase diagram is fairly well established in most regions. Also, separate studies have been made of the phase diagrams and thermodynamic properties for the three binary systems: CU-S,5,12-15 CU-Fe,11,14,17 and FeS.11,14,16,17 However, no work has

Jan 1, 1958

By F. M. Lewis, J. F. Meyers

In the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kid to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent non-sulphide material. It is not the purpose of this paper to discuss the nature of these various oxygen-sulphur compounds nor their effect on flotation, but to describe a method for correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.&apos; From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1947

By F. M. Lewis, J. F. Meyers

In the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kid to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent non-sulphide material. It is not the purpose of this paper to discuss the nature of these various oxygen-sulphur compounds nor their effect on flotation, but to describe a method for correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.&apos; From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1947

By I. Iwasaki, P. L. De Bruyn

Electrical double-layer properties of the silver sulfide-solution interface in different electrolytes and the influence the properties exert on the adsorption of dodecylammonium acetate (DAA) were studied using an electrochemical titration technique. The flotation behavior of silver sulfide was observed using DAA as collector and the results were correlated with adsorption measurements. Silver and sulfide ions were identified as the potential determining ions and their adsorption densities were measured as functions of the pAg and of the ionic strength at two different pH values. The point-of-zero-charge (PZC) was observed to be at pAg 10.2, the value being independent of pH and of the nature and concentration of the electrolyte used. The surface charge of silver sulfide in these electrolytes was positive for pAg values less than 10.2 and was negative for pAg values greater than 10.2. The adsorption of amine on silver sulfide surfaces at pH 4.7 was found to be strongly dependent on the pAg. A shift in the PZC towards a lower pAg due to the adsorption of amine indicated a specific affinity of dodecylammonium ion towards silver sulfide surfaces. At pH 9.2 a strong adsorption of the undissociated amine molecule was indicated. The PZC shift towards a higher pAg and the adsorption of the amine was virtually independent of the interfacial electrical conditions.

Jan 1, 1972

By R. S. Archer

THE name molybdena was employed by Pliny to denote various substances resembling lead. Later this name was applied to galena-the naturally occurring sulfide of lead-or substances of similar appearance. By the middle of the eighteenth century, it was applied to graphite and to the mineral sulfide of molybdenum (MoS2) now called molybdenite. This confusion is quite understand- able inasmuch as these substances look and feel very much alike. In 1778, the Swedish chemist Scheele published a treatise in which he pointed out essential differences between graphite and molybdenite. On treatment with nitric acid, molybdenite, unlike graphite, produced a peculiar white earth with acidic properties which he called molybdic acid. Since the same mineral gave off sulfurous fumes on heating, he concluded that it was a sulfide of molybdenum. In 1790, there appeared an account of the isolation by P. J. Hjelm of the new element molybdenum, as a metallic powder, by heating the oxide with carbon. It was not until Bertelius conducted the necessary experiments, about 1818 to 1825, that the foundation of the chemistry of molybdenum was laid. The only recorded use of molybdenum during the first century after its isolation was as a chemical reagent, primarily for the determination of phosphorus. It was not until the last decade of the nineteenth century that the use of molybdenum in steel appears to have been investigated. A

Jan 1, 1953

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.&apos; It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965

Experiments on the Rate of Heat Transfer from a Hot Gas&apos; to a Cooler Metallic Surface Members of the American Institute of Mining Engineers will be much interested in the subject of teat transfer from a hot gas to a cooler metallic surface, and although the book on this subject recently published by the Babcock & Wilcox Co., of New York, deals primarily with boilers, it contains a great deal of information which metallurgical engineers will find of great value. The book starts out with an introduction giving some of the current theories regarding this subject; it then describes in detail the experimental apparatus used, and the methods of conducting the experiment&apos;s and recording the data. Then follow some account of the determination of radiation losses in jackets and cooler; measurement of metal temperatures; detection and correction of errors; etc., concluding with a discussion of the results and derivation of corrective formula for heat absorption; heat pressure rate and specific heat of gas.

Jan 5, 1916