Search Documents

F. E. BACHMAN, Port Henry, N. Y. (written discussion*).-Experi-ments with titaniferous ores found in Essex County, New York, made by the MacIntyre Iron Co. in 1914, showed' that titaniferous concentrates are reduced in the furnace with no greater, and probably with less, expenditure of heat, and consequently of fuel, than non-titaniferous mag-netites; and as a greater proportion of their oxygen is removed by carbon monoxide than is the case with non-titaniferous magnetites, a lower fuel consumption for the reduction of iron may be expected. After the furnace was blown out at the end of the experiment, the formation in the hearth was found to be abnormal. The brickwork was replaced, entirely around the furnace, by a layer which at -the tuyere circle was made up of cinder, fine carbon, and coke; the coke, however, gradually disappeared toward the bottom, being replaced by cinder and graphite. The usual salamander of graphite and iron was missing. The material left in the hearth seemed to be cinder that had not drained from the last cast; its composition, though, would indicate that it was in the furnace previous to the taking off of the titaniferous ore. At first, this material was thought to be blast-furnace cinder mixed with less iron and graphite than is normal; but an examination showed it to be made up of cinder with small masses of iron and graphite. There were also patches of a steel-gray material having a metallic luster; a microscope showed these patches to be made up of black metallic crystals interlacing white crystals.

Jan 11, 1919

By R. P. Dolan, W. M. Shedd, B. L. Buchanan

Analytical expressions are derived from empirical data relating the basic physical device parameters to the radiation dose. To put in perspective and justify the approach taken, the overall problem and methods of attempted solution of radiation damage to transistors in a missile or satellite environment is briefly examined. The main emphasis is on a new criteria for neutron radiation hardness and the device design implications resulting from using this criteria. Contrary to other derived criteria, the derived bipolar hardness relation depends mainly on the initial lifetime rather than the base transit time. It is shown, that contrary to previously accepted beliefs, the inherent attainable radiation tolerance of JFET's is at least a factor of ten greater than the radiation tolerance ofbipolars. Experimental results on JFET's designed for maximum neutron radiation tolerance are presented. The accuracy, utility, and range of possible validity of various published lifetime and carrier removal damage constants are discussed. It is well known that transistors are subject to damage due to radiation at much lower radiation levels than those which would cause structural damage to a missile or satellite. The three principal categories of radiation damage to transistors are displacement, ionization, and thermomechanical. The main cause of displacement damage is fast neutrons, and the main effects which permanently degrade transistor operation are minority carrier lifetime reduction and carrier removal. A second-order effect is mobility reduction. The main cause of ionization damage is gamma radiation which results in permanent effects due to charge build-up in the oxide and transient effects due to photo-current generation. The transient effects are usually handled by using circumvention techniques in the electronics system. The extent of the transistor degradation due to displacement and ionization damage depends strongly on the transistor type, whereas the extent of thermomechanical damage does not depend on the transistor type, but depends mainly on packaging and metallization which are common to all transistor types. The standard transistor types are categorized in Fig. 1 and typical cross-sections are shown in Fig. 2. The original reason for the designation of the two classes of transistors was that the unipolar operation depends on only one carrier (majority) and the bipolar operation depends on both minority and majority car- riers. The bipolar is then seriously degraded by minority carrier lifetime reduction, whereas the unipolar or field effect transistor is not. One of the two principle classes of field effect transistors, the junction field effect transistor (JFET), depends strongly on carrier removal. However, the insulated gate (MIS) is little affected by either carrier removal or lifetime changes, but is virtually eliminated as a radiation resistant device because of permanent charge build-up in the insulator caused by ionizing radiation. The bipolar and JFET suffer only minor effects due to charge build-up in the oxide passivation when compared1 to the MOS. This is because the active region of the MOS is adjacent to or part of the oxide layer. It is then the bipolar and JFET which are potentially resistant to permanent radiation damage. DERIVATION OF RADIATION TOLERANCE RELATIONS Criteria. The bipolar is by far the most widely used transistor type. The usual criteria for hardening bipo-

Jan 1, 1970

By Karl D. Libsch, Modesto E. Erneta

Both battery design and environmental pressures are forcing the secondary lead industry to consider new and different processes. Trends in battery design are making normal decasing increasingly difficult. Lead in air, sulfur dioxides, and solid/liquid waste heavy metal restrictions are tightening. There is no clearly defined industry trend toward a given process, but it is clear that plants will be larger, less labor-intensive, and automated.

Jan 1, 1977

By C. M. Heath, B. W. Gonser

Soft solders are used principally in the automotive, can-making, building construction and electrical industries, but their field of usefulness extends well beyond these principal users to a vast list of miscellaneous applications where metal joints are required. The most common soft solders and the only ones considered in this discussion are those composed of lead and tin, with or without various relatively small percentages of impurities or additions. A small amount of antimony is often purposely added. As an indication of the importance of these lead-tin solders, 8620 long tons of tin were consumed in 1934 in the United States for making new solder, and during most of 1935 from 900 to 1000 long tons often were used each month. In addition, many thousands of tons of secondary solder are recirculated annually. A great many factors influence the properties of joints made with soft solders. Fluxes and the fluxing procedure used to prepare the surfaces to be joined in order to give a true metal-to-metal contact are among the most important of these factors. The temperatures used, cleanliness of the work and general soldering technique have their effect, but when results are unsatisfactory they are usually attributed to the metallic solder itself and the raw materials from which it is made. Sometimes criticism of the solder is justified. The wrong composition may be chosen for a given job, impurities may be present that ruin certain desired qualities, or uniformity may be lacking. A solder may even be looked upon with suspicion because of its ancestry, regardless of its true composition and behavior. To clarify the effect of slight differences in composition as found in commercially refined solders, a comparison of properties of solders grouped according to their origin has been undertaken. This investigation seeks to give practical information on the properties of tin-lead solders produced from virgin metals, from commercially refined secondary solder, and from an electrolytically refined crude

Jan 1, 1936

By J. M. Callow

The selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the so-called selective action. Her patent called for oils, either animal, vegetal or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Froment, an Italian, was granted a patent in which he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process. In the same year, Cattermole came out with a unique method. First, the pulp was emulsified with a small quantity of oil, by violent

Jan 1, 1916

SECTION I Page Page Manuscript Closing Date, Febru- Forthcoming Meetings xxvii ary Meeting v . Library xxviii New York Section War Meeting on Membership xxxii Ferro-Alloys v Biographical Notices: Minutes of Meeting, Board of Robert Bell, by F. D. Adams. xlix Directors xvii H. J. Cantwell, by H. A. Members in Military Service xviii Wheeler 1 Personal xxiii Institute Committees Iii Employment xxv Officers and Directors Ix

Jan 11, 1917

[EDMUND M. WISE, Chairman ROBERT H. LEACH, Past-Chairman D. K. CRAMPTON, Vice-Chairman CARL E. SWARTZ, Vice-Chairman W. M. CORSE, Treasurer LOUIS JORDAN, Secretary 29 West 39th St., New York, N. Y. Executive Committee 1941 1942 E. A. ANDERSON FRANCES H. CLARK D. L. COLWELL W. L. FINK W. P. SYKES J. T. NORTON 1943ERIC R. JETTE LOUIS W. KEMPF GEORGE SACHS]

Jan 1, 1940

By T. S. Lundy

Anand and Agarwala recently determined diffusion coefficients by the residual activity (Gruzin) method for several tracers in large-grained, high-purity aluminum. D values at any particular temperature in the range of 400" to 630°C were about four orders of magnitude lower for cd115, 1n114, sn113, and pdlm than for Ag. Corresponding values for Do and Q in the Arrhenius equation were also quite small. It was pointed out previously that unusually low diffusion coefficients within the region of a specimen near a free surface may be the major cause of such anomalous results for impurity diffusion in silver and in aluminum.44 Anand and Agarwala considered this possibility but rejected it because their penetration profiles were "homogeneous" and "yielded diffusion coefficients obeying the Arrhenius plot". Neither of these two criteria satisfactorily prove or disprove the presence of a near-surface effect. Such can be accomplished only by direct serial sectioning in which the chips ground from the specimen are assayed for tracer content. In fact, such experiments always should be done prior to use of the somewhat indirect Gruzin method where the finer details of the transport process cannot be determined. There have been several other reports of unusually low D, Do, and Q values for impurity diffusion in silver and aluminum.1"4 It is interesting to note that all of these studies made use of the Gruzin method. Also, in all cases where the same systems were examined by use of a direct serial sectioning technique, large near-surface effects were observed. One must conclude therefore that the reported anomalous diffusion parameters for cd, In114, sn113, and pd in aluminum are due to some near-surface effect, while the results for Agl10 indicate that no such effect was encountered for this system.

Jan 1, 1969

By T. Katayanagi, J. Shimoiizaka, K. Nakatsuka

Feldspar has been separated from silica by cationic collector using hydrofluoric acid as an activator of feldspar (1,2). Recently, one of the authors developed a new flotation process separating feldspar from quartz without using hydrofluoric acid. Presently, some silica sand mills are operating to introduce this process in Japan (3). In this flotation, feldspar is floated from silica using normal alkyltri-methylene diamine acetate together with sodium petroleum sulfonate as collectors in a hydrochloric or sulfuric acid circuit of about pH 2. From fundamental studies, it was found that, though the aliphatic diamine by itself did not adsorb on feldspar sufficiently to give a satisfying flotation in acidic circuit., the adsorption of collector was promoted by the simultaneous use of petroleum sulfonate and resulted in sufficient flotation of feldspar. On the other hand, quartz did not float in this flotation process. The application of this flotation was attempted for some types of natural samples and satisfying results were obtained. Further, an example of practical plant was introduced and the advantages in the process are emphasized.

Jan 1, 1976

By H. L. Gilbert, C. T. Anderson, W. J. Kroll

In a previous paper,' the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.% When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8 in. in diameter. The supply of direct current of high amperage for producing the desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flcxible tubing of the movable electrodc, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decsed to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 19oo"C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica accortling to the reaction: SiO² + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1949

By E. B. Harden, J. H. Harden

The practical use to which topographical models or relief-maps have been put, has within the last few years taken a wider range. They are rapidly coming into favor for other than purely scientific purposes, and their value for illustration and instruction is being more fully appreciated. Topographical maps; representing by contour-curve lines the elevations and depressions of the earth's surface, are now demanded in engineering work of nearly every description, and afford a ready means of bringing out the configuration of the country in a simple manner. A beautiful example of recent topographical mapping is seen in the seventeen sheets just issued by the Geological Survey of New Jersey. By reason of the inability of unskilled persons to understand the nature of a topographical map, it is sometimes necessary to con struct the same in relief, with the rivers, canals, railroads, etc., delin eated upon it. With the aid of such a map, problems in engineer ing science which would otherwise require expert assistance to explain them, are reduced to a simple and understandable form. Relief-maps are also of value to the geologist in working out the geological structure. To the instructor they present the most ready and efficient means of imparting clear and accurate knowledge of topography and kindred subjects. To the lawyer they are invalua ble in enabling him to bring into the court-room a representation of a part of the country with all its features accurately shown, to ex plain to the court and jury the special points about which litigation is pending and which would otherwise require long and laborious description. The application of the topographical map to business purposes is shown in a relief constructed by the writers for the Cumberland Valley Railroad Company and used by that company in the various ways of calling attention to the desirability of its route. This model is based partly on actual survey and partly on sketch topography. The horizontal scale is ,%, the vertical 1/19,200 of

Jan 1, 1888

In 1820, the Board of Public Works was considering some improvements to the canal, in order to reduce the cost of transportation, and in its annual report for that year gives a description of the method of loading the coal from the pit to the boat, and also from the boat to the dealer's yard, which is illuminating in showing how coal of this type should not be handled. It follows:- "It will be seen by the estimates, that the improving the present canal, forming a canal of large dimensions, from the head of the present lower canal to Sabbot Island; erecting locks of large capacity, and making a communication with the river, so as to completely accommodate the coal trade, (except it should hereafter be found necessary to make another communication with the river,) will not cost more than 126,000 dollars. But as there is some doubt whether the streams that may be received into the canal between Sabbot Island and the upper arch, will at all times be competent to supply the locks on that portion, we will extend our calculation to a point nearly half a mile above Pleasants' Island; where, by erecting a dam, any desired quantity may be thrown into the canal. This extension of the canal with one lock, and the dam across the river, is estimated at 34,000 dollars, making in the whole a little over 160,000 dollars. There will then remain a surplus of 40,000 dollars after completing the works to the point last mentioned. "In order to discover what effect the improvement of this first section will have on the tolls, it will be necessary to take a view of the present state of the coal trade, and endeavor to ascertain what change will result from the increased facility of transportation. "That part of the business which is carried on by water, is conducted nearly in this way. When the coal is drawn out of the mines, it is thrown in a heap near the mouth of the mine, or shaft; it is then loaded into carts, and carried to the river bank, where, in some instances, it is discharged from the cart at the brow of the bank, and runs down to the beach near the water's edge; then shovelled into wheel-barrows, and wheeled aboard of the boat, and discharged from the barrows by upsetting. In other instances, the carts are driven on to a kind of scaffold, furnished with a wide spout or director at the edge; by which the coal is conveyed immediately into the boats. These boats are the common James river poplar batteaux, and require three men to each. The up-stream navigation being laborious, the boats are built of light materials, and continue fit for service but a short time, (say) from two to three years; their cost, when new, from fifty to one hundred dollars. "When the river is tolerably flush of water, one of these boats will carry about two hundred bushels; but in low water their load is sometimes diminished to one hundred, and even as low as eighty bushels. They pay for passing the canals and locks to the Basin, one dollar per load; so that when full loads are taken, it will amount to half a

Jan 1, 1942

Albert R. LEdoux, New York, N. Y.—I can add a little to the information which has been given, by saying that it has been our business for some years, among other things, to inspect outgoing copper from some of the works here in the East, and to find out why there are variations not only in the conductivity of the wire-bars, but also in the character of the cathode-copper shipped; and we have found two things: These impurities which have been mentioned are largely upon the surface of the cathode. Samples taken of the inside, even of the nodules or " berries " which grow on the outside of the cathode, show that they do not contain more impurities than the denser material in the interior. In other words, it is a superficial deposit or contamination. There is still another reason for impurity in some of the copper which finds its- way to the manufacturers, namely, carelessness in the handling of molds or in casting. We have found copper which was comparatively pure, as far as the copper itself was concerned, but contained, mechanically intruded in the interior of the ingots,

Jan 1, 1913

By Ednlund D. North

Discussion of the paper of Edmund D. North, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 37, January, 1910, pp. 21 to 25. A. SCOTT REID, London, Eng. (communication to the Secretary*) :-As a constructor of several glass mine-models, I have read with much interest the description of the model of the Montana-Tonopah mine-workings by Edmund D. North. As an interchange of ideas and experience is always an advantage, and in view of the fact that such models are coming more and more into vogue, perhaps the following remarks on this subject may prove of interest to mining engineers generally and to Mr. North particularly. In the model of the Waihi gold-mine, New Zealand, which I constructed, a dust-proof case is used. The top, bottom, front, and two ends are of glass; the back only is of wood, painted a dull white, against which the mine-workings show very distinctly. Each mine-level is represented by a horizontal sheet of glass, supported on metal runners fixed to the uprights at each end of the case, in a manner similar to that described by Mr. North. The corner uprights are strengthened by having a metal band screwed to the inside face of each, to which the metal runners or supports for the sheets of glass are screwed in turn. The reason for having this additional strength is that as the mine is developed in depth, and fresh levels are opened, the increasing weight of the glass sheets, added to the model, caused the unsupported wooden uprights to bend slightly, so that the glass sheets-did not fit in with the desired nicety, and co-ordination was, to a considerable extent, lost. Strengthening the uprights in this manner is not important in models of mines in which only a few levels have been opened, or when the sheets of glass are small, but in the Waihi model there are 15 sheets of glass to be supported, and more to be added as development proceeds, and the weight is considerable.

May 1, 1910

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By G. Sachs, E. J. Ripling, J. J. Lynch

INTRODUCTION General IT is general practice to evaluate the strength properties of a particular metal from its stress-strain [(S1 - E1]) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress,"[ (s'r)], and a certain limiting strain, the "ductility" [(e1)], before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (a) the shape of the neck and (b) average values of the stresses and strains over the cross section at the moment of fracture. However, for the purpose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusions also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locus of failure. In this paper, the effects of straining (at room temperature) by various methods on [ ] the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to our present knowledge, any such prestraining results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain," from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1948

By Scott Howard

MANGANESE being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Ar3 transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the Ar3 transformation occurs at a temperature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3 quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Ar3 point as falling to 0° C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer,2 using alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 percent for the manganese content at which Ar3 is depressed to 0° C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

By Arthur Dwight

ARTHUR SMITH DWIGHT, president of the American Institute of Mining and Metallurgical Engineers, was born in Taunton, Mass., on March 18, 1864. He is descended on both sides from early settlers, one of whom was Richard Warren, of the "Mayflower." His forebears included Col. Benjamin Church, Tim-othy Dwight, and the Rev. Jonathan Edwards, third president of Princeton College. Mr. Dwight was graduated in 1882 from the Poly-technic Institute of Brooklyn, N. Y., and three years later from the Columbia School of Mines, with the degree of Engineer of Mines. In 1914, he received the honorary degree of Master of Science from Columbia. On leaving Columbia in 1885, he went to Pueblo, Col., and for thirteen years was associated with the Colorado Smelting Co. Beginning as assayer he rose to be general superintendent. When he gave up the latter position he became connected with several large companies in the mining and smelting of lead, copper and the precious metals in the Rocky Mountain region. This work occupied him from 1897 to 1906, and six years of that time were spent in Mexico. He was general manager of the Greene Consolidated Copper Company at Cananea, Mexico, in 1906, when trouble first developed against the régime of Diaz. A general uprising was planned to seize the mines, and with money and supplies so obtained, carry the revolt through the interior. Mr. Dwight turned his industrial organiza-tion into a military unit almost over night, stemmed the tide of revolution, and had the situation well in hand before the arrival of troops. In the fall of 1906 he returned to New York and began practice as a consulting mining and metallurgical engineer. He next developed important metallurgical patents for the roasting and agglomeration of fine ores, known as the Dwight and Lloyd sintering process, now extensively used ail over the world.

Jan 3, 1922

By Alden B. Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form 1133). In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc f were deformed and examined micro-

Jan 1, 1938