Search Documents

By I. R. Kramer

The effect of the specimen diameter, d, on the flow stress, cra of polycrystalline aluminunz (99.997) was studied. The increase in the flow stress could be accountedfor by the increase in the surface layer stress, with decreasing specimen diameter. Both , and a, were found to be proportional to For the smaller-dianzeter specimen (< 0.033 in.) at strains less than aboul 0.1, the work hardening of the surface layer was greater than that associated with the bulk of the specimen. At higher strains the work hardening due to the bulk appears to be independent of the specimen diameter. THE increase in the strength of metals with decreasing diameter is well-known; however, an adequate explanation for the cause of the size effect is still lacking. The earliest systematic investigation of size effect appears to be that of Onol who reported that for aluminum monocrystals the resistance to slip at low strains increased as the specimen diameter decreased. A change in the stress-strain curve beyond 0.001 strain was not found. However, Suzuki et a1 .&apos; reported for monocrystals of a brass and copper having diameters in the range of 2 to 0.12 mm that the entire stress-strain curve was raised as the specimen diameter was decreased. The effect of size was most apparent when the diameter of the specimen was less than 0.5 mm. In the discussion of this paper Honey-combe reported a size effect in copper crystals as large as % in. diam. These results are in agreement with those of paterson3 and Garstone et al.4 While the majority of the investigations on size effects was conducted in terms of the variation in the diameter of the specimen, several investigators studied the influence of the specimen geometry. For example, Wu and smoluchowski 5 reported that in aluminum monocrystals the slip system was a function of the specimen dimension in the slip direction. King-man and Green 6 studied the influence of size on the compressive stress-strain relationship of aluminum monocrystals when the ratio of length to diameter was constant. Their specimen diameters ranged from to & in. For specimens oriented for single slip the critical resolved shear stress for the smaller-size specimens increased with decreasing diameter. No effect was observed in the large-size specimens. Specimens having an orientation near the corners of the stereographic triangle did not exhibit a size effect. Apparently, the increase in strength with decrease in the diameter of the specimen is a general phenomenon and has been observed in a brass |T and cadmium as well as in aluminum and copper.&apos; In a series of investigations (for example Ref. lo), it was shown that during deformation a surface layer was formed which imposes a back stress, a,, on the moving dislocations. It is reasonable to predict that this surface layer stress, as, should be a function of the specimen diameter and could possibly account for the flow stress size effect. In fact, experimental evidence will be presented to show that this is the case; i.e., the increase in flow stress with decreasing size is equal to the increase in the surface layer stress, as, with size. In addition, data will be presented on the variation with size of and a* where is the back stress associated with the generation of dislocation obstacles in the bulk of the specimen and a* is the net effective stress acting on the mobile dislocations. A limited investigation was carried out on gold specimens to determine the influence of an oxide film. EXPERIMENTAL PROCEDURE The aluminum specimens were prepared from -in. bar stock (99.997 pct purity). The 0.350- and 0.150-in.-diam specimens were machined directly from the bars while the specimens having a diameter of 0.033, 0.020, and 0.015 in. were prepared by swaging and drawing to 0.04 in. and electropolishing almost to final size. The specimens were prepared with a 2-in. gage length. The specimens were annealed in vacuum (-10-4 Torr) at 350°C for 8 hr. The grain diameter of the specimens in the various specimen diameter groups was 0.08 ± 0.02 mm. Gold specimens of two diameters, 0.14 and 0.03 in., were prepared in a similar way and annealed at 650°C for 8 hr. The grain diameter of the gold specimens was 0.2 mm. After annealing the specimens were electrochemically polished to the final size and tested in an Instron tensile machine at a strain rate, E&apos;, of 10- 3 per min. While it was possible to determine the surface layer stress, a,, in the larger-size specimens by measuring the difference, Aa, between the stress before unloading the specimens and the initial flow stress after removal of the surface layer as outlined in detail in Ref. 10, this method is not applicable for small wires because of the difficulty in obtaining a sufficiently accurate measure of the diameter. The values at the various strains were therefore determined by measuring after the specimen had been annealed at 35°C for 4 hr. It has previously been shown" that the two methods give the same results for a provided that the annealing temperature is low enough to affect only the surface layer and not the dislocation barriers in the bulk of the specimen. For the gold specimens a treatment at 150°C for 16 hr was found to be satisfactory for the determination of by the low-temperature annealing method. EXPERIMENTAL RESULTS Determination of a,, and a,. The stress-strain curves for the various diameter aluminum specimens, plotted in terms of the logarithms of the true stress, and true strain, are given in Fig. 1. These curves represent the average data taken from at least ten specimens at each size. Over the range of strains investigated the curves follow the empirical equation

Jan 1, 1968

By Robert A. Haney, Stephen J. Gigliotti, James L. Banfield

A series of investigations were made by the Mine Safety and Health Administration to evaluate the performance of various face ventilation systems as part of a program to reduce frictional ignitions of methane and to develop face ventilation systems that could be used with the line brattice more than 10 feet from the face. Tests were conducted in a full-scale laboratory model of a face area. Systems tested included unassisted blowing and exhaust line brattice, diffuser fan and spray fan systems. Systems were evaluated at air quantities ranging from 1.4 to 7.0 m3/s (3,000 to 15,000 cfm), and brattice-to-face distances from 1.5 to 9 meters (5 to 30 feet.). Tests were designed so that systems could be evaluated for the location of the high-point methane concentration in the face area, methane dilution capacity, and face ventilation index. The methane dilution capacity is the total amount of methane a system can dilute to 1.0 volume-percent. The face ventilation index is the efficiency at which the available face air volume is being used.

Jan 1, 1982

By Benjamin N. Webber

During World War II the Pocos de Caldas bauxite deposits of Minas Gerais in Brazil yielded some 60,000 tons. Since then they have maintained a small but almost continuous production. Known for many years, the deposits have been reconnoitered by a number of geologists,1-4 but no dimensional study has been possible because there have not been enough exposures to show clearly the depth, bedrock, and habit of occurrence. The deposits are somewhat unorthodox in their occurrence mainly on steep slopes of mountainous terrain. Although the parent rocks are a sequence of alkalic intrusions that bauxitize readily under the proper conditions, bauxitization has not been the dominant weathering process in the area. It is limited to certain localities where important volumes of bauxite have formed by laterization of several rock types, each yielding a distinctive type of bauxite. Bauxitization may be observed in several stages and in both direct and indirect cycles of formation. The deposits are unique in being of demonstrably recent age, so that the conditions under which the bauxite formed are essentially those of the present time. The bauxitization sequence is postulated in Fig. 1.

Jan 8, 1959

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.&apos; When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

Members Dues Resignations, Suspensions and Expulsions Institute Meetings Board of Director?s Meetings Directors and Officers Duties of Officers Committees Nomination and Election of Officers Publications Divisions, Local Sections, Affiliated Societies Amendments [As REVISED FEBRUARY 21, 19281 ARTICLE I MEMBERS-QUALIFICATIONS AND ELECTION , SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Associates; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that Junior Associates, and all Members and Associates whose residence shall be outside of the United States of America, Mexico and Canada shall not be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1928

By Jean Bonnemaison

Societe Miniere & Metallurgique de Penarroya Noyelles-Godault works are located in the northern part of France. The complex includes a lead smelter, a zinc smelter, shops for production of manufactured products and all necessary general services. The zinc smelting complex described in this paper was designed in 1959 to replace an old horizontal retort distillation furnace and was first operated in May 1962. It includes: - a sinter plant producing the zinc sinter for the Imperial Smelting furnace : zinc, lead and bulk zinc-lead concentrates are sintered on a Dwight-Lloyd machine with a working area of 80 sq.m. Cadmium sludges are treated by the wet method in a separate plant for recovery of cadmium. Sulphur dioxide contained in gases goes to a gas washing tower and is subsequently made into sulphuric acid in a plant with a capacity of 550 m.t. per day. - a smelting plant where the process developed by Imperial Smelting Processes Ltd. is applied : the blast furnace which was modified in 1967 has an area of 17.5 sq.m. at the tuyeres level and a section of 24 sq.m. at the top of the shaft. It has a theoretical zinc capacity of 100,000 m.t. per annum. Air blast is heated by means of covers up to the theoretical temperature of 950ºC. Zinc produced is either directly cast into slabs for sale as standard &apos;good ordinary brand&apos; zinc, or sent to a refining plant where the New Jersey process designed to produce &apos;special high grade&apos; zinc is in application. Mixes of zinc containing various amounts of lead, cadmium or aluminum are prepared to customer specification in a mixing plant.

Jan 1, 1970

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.&apos; " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By John M. Logan, John Handin

Quasi-dynamic triaxial compression tests have been done for the first time at confining pressures to 7 kb. The intermediate strain-rate apparatus employs a gas loading cylinder which allows axial strain rates up to 102/sec on a sample 2 cm in diameter and 4 cm long. Samples can be deformed at confining pressures to 7 kb. Strain gages bonded to the loading piston and to the jacketed specimen allow internal measurements of load and sample strains respectively. Westerly granite has been deformed at confining pressures to 7 kb, room temperature, and axial strain rates of 10-2 to 1/sec. An increase of ultimate strength with confining pressure was found as expected. The ultimate strength was also found to vary directly with increasing strain rate; the rate of rise increases with confining pressure. Brittle deformation has dominated the sample behavior. Solenhofen limestone has been deformed at confining pressures to 3 kb, room temperature, and axial strain rates of 10- to 10/sec. The brittle-ductile transition was found to take place at about 1.5 kb confining pressure at a strain rate of 10/sec.

Jan 1, 1971

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.&apos;&apos;&apos; A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.&apos; In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.&apos;&apos;7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By J. M. Blank, V. A. Russell

When the nucleation of silicon on a sapphire substrate is accomplished by gradually decreasing the substrate temperature while subjecting it to a constant impingement rate of hydrogen and silicon tetrachloride, the resulting deposit is characterized by widely separated islands of silicon scattered over an "open sea" of sapphire. Analysis shows that nucleation takes place mainly on sites of large adsorption energy, about 85 kcal per mole, and small surface concentration, about 108 cm-2. Crystal growth proceeds rapidly on these nuclei and results in enough depletion of Sicl4 from the ambient gas to suppress further nucleation. The technological importance of single-crystal films on dielectric substrates has prompted considerable work on the deposition of silicon on sapphire. This paper is concerned with the deposition of silicon, by the reduction of silicon tetrachloride with hydrogen, onto heated sapphire substrates. The apparatus consisted of a temperature-controlled container for the silicon tetrachloride along with gas lines and flow meters necessary to convey a hydrogen-silicon tetrachloride mixture to a reaction chamber constructed of quartz tubing. Heat for the substrate was provided by means of an inductively heated graphite susceptor. The observations pertinent to the present discussion were made with an American Optical Co. high-temperature microscope which allowed us to make motion pictures of the deposition process at a magnification of approximately 50 times. Two main categories of experiments were carried out: one on determination of critical condensation temperatures and the other on the deposition of epitaxial silicon films on the sapphire substrates. Critical condensation temperatures were determined in the traditional way by raising the substrate temperature well above that at which condensation could be expected at the impingement rates being studied and then gradually lowering the temperature until the condensation of the first silicon was observed. This was done initially with ellipsometry-type detection but it was soon discovered that the deposits were occurring as widely separated islands and groups of islands scattered over an "open sea" of sapphire. We have called these archipelago formations. They were most easily detected by optical microscopy. Data gathered from experiments of this type have been collected in Table I. Motion pictures of the formation of archipelago patterns show that the nucleation period lasts about 10 sec if the substrate temperature and impingement rate are kept constant. Essentially all of the nuclei are formed in a few seconds and all subsequent silicon deposition merely adds to the size of the established nuclei. After an archipelago formation has matured at a given substrate temperature and impingement rate, it is very difficult to stimulate any further nucleation in the open space between islands. Lowering the substrate temperature will occasionally stimulate nucleation but increasing the impingement rate hardly ever produces any more new nuclei. It should also be emphasized that the nucleation rates appear to be very small, about 104 cm-2 sec-1. They will receive special attention in the analysis section. Another series of experiments was performed employing a systematic variation of substrate temperatures and impingement rates approximating those expected to produce epitaxy. Sapphire substrates with surfaces normal to the 2233 direction were used. In contrast to the procedure that produces archipelago patterns, these films were deposited by raising the substrate temperature to a desired value at which time the silicon tetrachloride and hydrogen flow was begun. Of course, these depositions produced mainly films that were continuous. After removal from the deposition chamber, the substrate and silicon film were examined microscopically to determine the nature of the deposit and by X-ray diffraction to determine the extent to which a single-crystal film had been achieved. Results of these experiments are summarized in Table 11. Of interest for the present analysis is the fact that epitaxy appears to be confined to a fairly narrow temperature range between about 1050" and 1150°C. This also will be discussed in the analysis section. ANALYSIS In this section we shall apply nucleation theory to the data presented above with the objective of testing

Jan 1, 1967

By K. N. Han, H. Lee, M. C. Fuerstenau

An investigation of the recovery of finely-divided cassiterite and silica particles less than 1 µm (1200 mesh) in size has been carried out using packed and fluidized beds. The bed particles used included cassiterite and silica particles ranging from 44 to 210 µm (325 to 70 mesh). Effects of various system parameters on the recovery and selectivity of cassiterite fines were investigated. System parameters included pH of the slurry solution, superficial velocity, slurry concentration, and bed particle sizes. High recoveries of cassiterite fines were obtained at pH 4.0 and slow slurry flow rates. In a packed bed system, recovery of cassiterite fines was greater than 95%, while that of silica fines under the same conditions was about 35%. Although the total recovery per pass is not as good as the packed bed, the fluidized bed system exhibits good recovery in general and an excellent selectivity of cassiterite fines. There is an optimum superficial velocity, vo, for the rate of fine particle uptake and the apparent rate constant has the form of Kvo1/2- K&apos;vo, where K and K&apos; are system constants.

Jan 1, 1985

By Olav Idelgeland

FROM indirect evidence point defects have been believed to influence the fatigue behavior of metals and alloys.1,2 Measurements of changes in resistivity made after cyclicstressing at low temperatures indicate that a very high density of defects is present, part of which may be removed by room-temperature annealing.3&apos;4 These results are consistent with the generation of a high number of point defects at low temperatures. Corresponding measurements made after room-temperature stressing did not show any recovery effects.3 This was attributed to a stabilization of the dislocation network after a few thousand cycles without generation of vacancies. In this laboratory resistance measurements of copper single crystals, shaped as normal fatigue specimens ,5 have been made with a Kelvin double bridge at room temperature during and after cyclic stressing at 80 cps by comparing with a dummy at a close and constant temperature. Temperature differences were measured to ±0.025°C with fine thermocouples taped onto the gage lengths. Potential leads were tin-soldered into small holes in the gage length to give stable values. Corrections for differences in temperature and changes in mean length of the specimen were made according to the formula:

Jan 1, 1968

Carlisle: Jim Knapp, has been the good friend of hundreds-maybe thousands-of mining men in these western states in the last 40 or 50 years. Jim is going to talk about many of the mining camps of Nevada, where he has done plenty in the mining field during the last 50 years. Jim, for a starter, how did you happen to go to Nevada? Knapp: In the summer of 1902, two years after the discovery at Tonopah, the professor of mining at Stanford sent out myself and another student by the name of Joe Miller to make a report on the camp. We left San Francisco at 8 p.m., got to Reno the next morning, then took the train to Sodaville, arriving about 4:30 in the afternoon. The first man I met when I arrived at the Tonopah station was Tasker Oddie, a gentleman who later became the Govenor of the State and then a United States Senator. Before we got away from the stage station I also met S. H. Brady, the first mining engineer to put out his shingle in Tonopah. He afterwards became general manager of the West End Mining Co.

Jan 3, 1965

By E. J. Ripling

A NY mechanism proposed to explain hydrogen embrittlement in titanium and its alloys must, of course, be consistent with the experimental data that characterize this embrittlement. Unfortunately, however, the mechanical behavior of hydrogen-bearing titanium, at least a-ß titanium, has not been unequivocally defined. Lenning, Craighead, and Jaffee have clearly shown that hydrogen cmbrittles a-titanium by elevating its transition temperature, probably as the result of the formation of titanium hydrides. Therefore, in these alloys, hydrogen acts like at least one other interstitial contaminant, namely, nitrogen.&apos; On the other hand, ß-titanium has been shown by these same investigators to tolerate very large amounts of hydrogen without suffering severe mechanical damage.2 Mixing these two phases, however, to form the most important class of commercial alloys, the a-ß alloys, again results in severe hydrogen embrittlement, although the mechanism by which the embrittlement is produced is not of the same type as that which causes brittleness in a alloys. Ductility damage due to hydrogen increases as the strain rate is reduced in a-ß alloys, while embrittlement in a alloys increases as the strain rate is increased, since the latter is a transition temperature behavior. Steel, like the a-ß alloys, becomes more hydrogen sensitive at slow strain rates, suggesting that the mechanism producing the embrittlement in these two metals is similar. Brown and Baldwin&apos; described the hydrogen-produced ductility depression in steel as a function of testing temperature and strain rate by defining the slope of the two surfaces that produced the depression in a three dimensional chart, Fig. 1. One of these surfaces was given by the equations (de/de)4 > 0 (de/dT) < 0 [1] while the other was defined by the pair of equations Surfaces of the type given by Eq. 1 are suggested in two ways. One is an embrittlement mechanism wherein the diffusion rate of hydrogen is competitive with the rate at which the material is being deformed, as suggested by the planar pressure theory of Zapffe and his co-workers.&apos; The other is the diffusion controlled extension of Orowan&apos;s theory on delayed fracture in glass by Petch and Stables.&apos;&apos; Surfaces of the type given by Eq. 2 are also compatible with a mechanism of pressure build up in voids, according to de Kazinczy,&apos; since the solubility of hydrogen in the metal increases with testing temperature so that as the temperature is raised, the pressure in the voids is reduced. Kotfila and Erbin recently presented some data on the dependence of ductility on testing temperature and strain rate for the a-ß 3 pet Mn complex alloy at four different hydrogen levels.H Although data were presented for only three testing temperatures at three different strain rates, their results indicated that surfaces of the types defined in Eqs. 1 and 2 are produced in the alloy when the hydrogen level is sufficiently high—200 and 300 ppm—Fig. 2. Jaffee and his co-workers presented data on a number of different a-ß alloys which indicated the existence of surfaces of the type described by Eq. 2, but the ductility recovery at low temperatures as given by Eq. 1 was not found." In an attempt to aid in crystallizing this description of the ductility dependence of hydrogen-bearing a-ß alloys, tests were conducted by the author on a-ß titanium 140A with three different hydrogen contents. The tensile properties of two as-received rods and one vacuum annealed rod* were obtained over a range of testing temperatures and strain rates as shown in Figs. 3 and 4. Hydrogen analyses were made by the Battelle Memorial Institute on four pieces of the rod whose properties are shown as solid circles in Fig. 4. The hydrogen content of these pieces, taken at widely spaced intervals within the rod, were 280, 270, 289, and 270 ppm, indicating that the hydrogen content within a single as-received rod was quite uniform. One of the broken test pieces whose properties are shown in Fig. 3 as solid circles was also analyzed, and found to have a hydrogen content of 310 ppm. The analyses obtained on two of the vacuum annealed specimens were 92 and 170 ppm.

Jan 1, 1957

By Rollin E. Hook, Attwell M. Adair

The yield and fracture behavior of recrystallized chromiztm have been studied in order to gain an understanding of the recrystallization embrittlement-rheotropic recovery phenomenon. The duc tile-brittle tensile transition temperature of recrystallized chromium was found to vary from 225 ° to -80°C as the ratio of specimen diameter/mean planar grain size decreased. The applicability of this observation to other bcc metals is briefly discussed. Brittle fracture in recrystallized chromium was found to be initiated predominately from intercrystalline rupture nuclei. Single crystals exhibit a high degree of ductility at 23 "C. The experimental data indicate that grain boundaries play a significant part in the yield and fracture behavim. Pres training significantly reduces the transition temperature, and high temperature aging does not result in re-embrittle-ment until complete recovery or re crystallization occurs. SEVERAL theories have been used to explain the recrystallization embrittlement-rheotropic recovery phenomenon in chromium. Wain, Henderson, and ohnstone&apos; propose a Cottrell dislocation locking mechanism due to nitrogen, and Weaver and Gross and weaver 3 propose a strain-induced precipitation mechanism involving a chromium nitride precipitate. The researches of many investigators seem to leave little doubt that brittleness in chromium is promoted by interstitial impurities. Smith and seybolt4 have shown that the ductile-brittle transition temperature is lowered as the interstitial content is reduced. weaver3 provides evidence for a 150°C reduction in the tensile transition temperature as the nitrogen content is reduced from 20 to 5 ppm. Maykuth and affee&apos; have suggested that the amount and orientation of grain boundary impurities may be responsible for the brittle nature of recrystallized chromium. This suggestion was based on their findings that wrought iodide chromium possessing a fiberous grain structure is ductile in tension at room temperature while a recrystallized grain structure is completely brittle. Previous investigations have not studied this phenomenon sufficiently to determine its cause. Perhaps this has been largely due to previous experimental findings that brittle fracture observed in chromium has been almost entirely transgranular.&apos; In addition McNeil and imb,&apos; who investigated coarse-grained as-cast chromium, describe the point of initiation of fracture as cleavage, close to the (100) plane, near or at grain bound-daries, or at included particles or voids. However, Hook, Adair, and ipsitt found that fracture in coarse-grained recrystallized chromium is initiated by intergranular rupture and then propagates nearly entirely by cleavage. This result, together with their finding that room temperature ductility in bending is observed for single crystals and coarse-grained polycrystalline specimens for which the number of grains through the specimen diameter is small, suggests that grain boundaries may play an important role in the brittle behavior of chromium. The recrystallization embrittlement problem can be resolved into two questions. These are, whether the controlling mechanism is predominately one of crack initiation or crack propagation, and whether brittle fracture is initiated predominately by slip or twin induced intergranular rupture or by cleavage. The following research was designed to study the role of grain boundaries on the brittle fracture of chromium in an effort to resolve these questions. EXPERIMENTAL PROCEDURES, RESULTS, AND DISCUSSION General Procedure. All tensile specimens (except 0.04 in. diam wires) were prepared from 1/4 in. diam swaged rod fabricated from one ingot. Details of fabrication are given elewhere. The results of impurity analysis for the swaged rod and for the

Jan 1, 1963

By W. A. Backofen, M. L. Ebner

SINCE the early work of Gough with Hanson and Wright,l-3 the study of fatigue has been characterized by experiments on single crystals only in recent times.9-10 Now, increasing attention is given to this aspect of fatigue research for the insight that it may provide into details of mechanism. The investigations have concentrated to a large extent on the development of deformation markings on fatigued crystals, and have shown the cracks to originate in slip bands possibly preceded or accompanied by slip-band extrusions. Experiments of special interest to the present work were conducted by paterson5 on copper crystals and involved both metallographic examination and measurement of change in flow stress. Crystals were cycled in alternating tens ion-compress ion with a constant plastic shear-strain amplitude of approximately 0.8 pct, and were particularly revealing for their demonstration of hardening with accumulated strain similar to that in unidirectional straining, through an easy-glide stage I followed by a stage II of rapid hardening; deformation was not continued beyond 40 cycles, however, so that the eventual course of the hardening curve could not be decided. For the conditions used by Paterson, surface slip markings were similar to those observed in unidirectional straining, but there were no X-ray asterisms and no deformation bands on the surface. In current thinking about the nature of fracture in fatigue, two views relative to mechanism are generally acknowledged, with the reservation that both could apply simultaneously in some measure. As one possibility, fracturing across a slip plane is regarded as a result of loss of cohesion from the creation of many point defects by dislocation movement under the cyclic loading.&apos;&apos; On the other hand, fracture has also been taken to follow as a consequence only of the geometry of slip at a free surface, consisting of offsets and crevices which eventually become fatigue cracks.12, l3 The work of McCammon and Rosenbergl4 showing fatigue in polycrystals at 4.2oK makes clear that any long-range diffusion of point defects is unnecessary, yet studies such as those of Forsyth and stubington15 show that accelerated diffusion may be a characteristic of deformation under fatigue loading. Interest in obtaining data of possible use for resolving such questions led to the experiments described below. Copper crystals were conveniently loaded in alternating four-point bending at constant deflection, a test condition shown to approximate a constant plastic strain amplitude for a wide range of axial orientations. The method of testing was not readily adapted to extensive study of temperature effects, but an investigation of the geometry of crack formation could simply be made by orienting,the slip direction at different angles to the surface. EXPERIMENTAL PROCEDURES Single crystals were grown by a modified Bridgman method in a stationary gradient furnace under an atmosphere of purified dry nitrogen. Purity of as-grown crystals was 99.999 pct as determined by spectrographic analysis plus vacuum fusion and gravimetric analyses for oxygen and sulfur, respectively. Crystals were of reasonable perfection as evidenced by a critical resolved shear stress at 10 deg from (110) of 60 g per sq mm and half-width of a (400) X-ray diffraction line from one crystal of

Jan 1, 1960

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors&apos; k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system&apos; is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.&apos; The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953