Search Documents

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

By Júlio C. Lúcio

Consider the case of a mining company with N investment opportunities in projects of different commodities. The problem is: since the company has limitation of capital, equipments, technical staffs, etc, what is the best portfolio of production projects in order to maximize expectations from shareholders? In the no-longer past, the traditional method for the selection of portfolio of projects was the rank-an-cut method. But, this does not properly account for the risk to which the company is exposed. The Markowitz?s Mean-Variance is an advance because the risk of the NPV can be estimated at the level of the company or even division of the corporation. The final product of the Markowitz?s model is the efficient frontier, in which, the manager can clearly understand the maximum return from existing assets and the associated risk level - but this model does not recommend which one is the best portfolio. In this paper we present a model to select the best portfolio considering not only economic indicators, but also requirements of production, constraint in investments, etc. We show that if investors are diversified, managers should select projects with highest return, regardless of risk. However, in practice, if bonuses of managers are tied to their performance, the choice for portfolio with lower return and risk can happen. Numerical application considering typical portfolio of large mining company is used as example.

May 1, 2009

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain-softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OB/IB) ratios of less than 5, interactions do not occur, and that for OB/IB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OB/IB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

CSIRO Mineral has recently developed a new electron microprobe based system for characterizing zircon grains from heavy minerals sand deposits. The system acquires cathodoluminescence (CL) spectra, X-ray and backscattered electron (BSE) signals in parallel. By scanning over a specified target area, CL wavelength and X-ray element distribution maps of polished zircon grains can be acquired. Post-inspection of the combined dataset using in-house developed software enables correlations between chemistry and structure to be investigated. The new method offers significant benefits over traditional CL and BSE techniques in that direct comparison with the elemental concentrations over the same region is now achievable. By combining the electron microprobe results with data for the same mapped region obtained via a nuclear microprobe, significantly better detection limits (~ 1ppb) for elements with atomic numbers greater than iron are possible. The ability to measure spatially related analytical data and then investigate the correlation of the CL spectra with chemical data is an important advancement in the characterization of zircons. Key words: zircon, characterization, cathodoluminescence, backscattered electron, electron microprobe, nuclear microprobe, chimage, proton induced x-ray emission.

Jan 1, 2003

By Brian W. Stump

"Seismic waves from explosions can be used to characterize physical processes in and around the source. The quantification of absolute levels of ground motion is important for minimizing impact on nearby people and structures. We contrast work in characterizing seismic radiation from contained nuclear explosions with ground motions from multiple explosion quarry blasts. A physical basedunderstanding of the explosion source function allows prediction and extrapolation to new environments where experimental data may not exist."

Jan 1, 1990

By Frederic Vanderoost

Actualmente, el manejo adecuado de las informaciones geológicas en el sector minero optimiza recursos y maximiza resultados. En ese sentido, el presente texto señala la implantación de un conjunto de herramientas para la administración de banco de datos geológicos, de forma corporativa y manteniendo un informe central de datos. Dichas herramientas se basan en sistemas comerciales de base de datos como Oracle, Microsoft SQL Server y Sybase, los cuales garantizan agilidad, flexibilidad y capacidad de almacenamiento para el manejo de informaciones adecuadas y las operaciones típicas de la industria minera. Asimismo, se presenta estudios de casos, analizando sus ventajas, limitaciones y dificultades encontradas en una mina.

Aug 25, 2002

By M. Schafer

The 20 foot diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT-3) has been completed. This paper will summarize aspects of liner design and address the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented.

Jan 1, 2008

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004

By Karl Zipf

In highwall mining, once a sufficient number of web pillars are developed, they can fail catastrophically in a domino-type failure, posing a safety hazard to highwall miners and sterilizing mineable reserves. Three recent case histories of catastrophic web pillar failure in U.S. and Australian mines are documented and analyzed with two design approaches. The conventional design approach uses only a strength criterion, while the postfailure design approach uses both strength and stability criteria to insure an acceptable failure mode should strength failure occur. Catastrophic highwall web pillar failures can cost money through equipment losses, production losses, coal reserve sterilization and lost opportunity costs. Coal recovery may be higher. but the benefits of higher recovery must balance the potential costs of failure. Application of the conventional or postfailure design approach will decrease coal recovery and revenues, but the risk of potentially costly failure is much less.

Jan 1, 1999

By Dirk van Zyl

As part of the North American regional activities during the Mining, Minerals and Sustainable Development Project (MMSD) one project focused on the development of sustainability evaluations at the operations level. Engagement was identified as one of the seven important questions to be addressed. Engineers and scientists employed in the mining, minerals and materials production arenas must understand the importance of stakeholder engagement, both within and outside the operations as it is essential in the ongoing activities required to contribute to sustainable development. After developing the awareness that a social license can only be contemplated if engagement is in place, they also have to develop skills in engagement processes. This presentation will present the business case for engagement as well as an approach to motivate undergraduate mining engineers to embrace it. The presentation will also review some recent and ongoing research to improve the engagement process.

Jan 1, 2010

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

Tracey Khanna, Assistant Editor of UK?s Mining Magazine discusses some of the new and important environmental challenges, physical and social, that are facing mining companies. The tide of public opinion has turned strongly against those companies which are unable to show that they are practising responsible environmental stewardship. This is, no doubt, in part due to the recent focus of the international media on environmental issues and constantly improving means of communications, which has brought the whole subject of mining and the environment to those who, in the past, had only a limited awareness of the industry. Mining companies today face new and important challenges with regard to the environment, both physical and social. New technology and a greater understanding of waste management techniques has helped to bring about improved handling and disposal of mines wastes, so reducing some of the impacts. However, improved technology has also brought about the economic viability of exploiting increasingly lower-grade ore from open pits, resulting in a greater visual impact.

Jan 1, 2000

By A. F. Banks

"Potash processing in Canada commenced on a commercial scale in 1962. Over the last 25 years it has grown into a world-class industry with many advances in processing technology. As it is a relatively young industry, many more advances can be expected. Unlike much of the mineral production in Canada, potash is sold as a range of finished products. The processing involves potash recovery and finishing in about equal amounts in terms of the effort of processing. Environmental concerns are not insignificant and are being treated uniquely in some areas. Research and development efforts, while not carried out on a large scale, are attacking industry problems on a wide front.THE INDUSTRYThe Canadian potash industry has 12 producing mines, 10 in Saskatchewan and 2 in New Brunswick. The total productive capacity of the industry is 18,300,000 tonnes of products per year. At capacity, the industry 1•ill process the equivalent of about 53,000,000 tonnes of ore per year. Plants range in size from 8,000 tonnes to 24,000 tonnes of feed per operating day. In product terms this is from 2,500 to 3,500 tonnes of products per day.Of the 12 mines, 11 are conventional underground mining operations with potash recovery principally by flotation supplemented by crystallization and one is a solution mine where mining is achieved by dissolving the potash and salt in underground caverns and then treating the solution in an evaporator/ crystallizer circuit. In all plants there is commonality of unit operation in the product screening and compaction sections. There are three principal ores being treated in the conventional plants. These may be characterized in general terms as follows:"

Jan 1, 1987

By Tingkan Lu

To understand the reinforcing mechanisms of the fully grouted resin bolt and clarify its performance in weak roof strata, the field monitoring investigation using instrumented bolts has been conducted in a coal mine. The total time of monitoring was around ten months. In the first 8 month period, the rock bolt performance relates to the initial development of the gateroad and subsequent time dependent strata response. After 8 months, the rock bolt performance relates to the effect of the approaching longwall mining operation, up to the point where the measuring station was destroyed due to the mining operation.

Jan 1, 1998

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By T. N. Singh

An evaluation was made on the cavability of the roof formation of Dishergarh seam including caving sequence, caving span, and load on powered support.

Jan 1, 1994

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010