Search Documents

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

By B. Wilshire, P. W. Davis

It has been shown that grain-boundary migration during high-temperature creep can reduce or even prevent the formation of intercrystalline voids, giving a considerable increase in ductility.' A similar observation has been made in a recent investigation of the creep properties of various grades of nickel and nickel alloys. The results can be illustrated by the observations made on: a) Pure vacuum-cast nickel (99.993 pct Ni) b) Impure vacuum-cast nickel (99.97 pct Ni) c) Pure nickel containing internal voids (produced by a process of intering). d) A substitutional solid solution alloy of pure nickel containing 1.16 pct Sn. All the materials were given a high-temperature anneal (>850°C) to produce a stable grain size of 7 to 10 grains per linear mm. The apparatus and techniques used to obtain the present results have been described elsewhere.' In this series, grain growth was observed only in the highest-purity, vacuum-cast metal. Thus we may consider that in the other materials grain-boundary migration was prevented by either preexisting voids or solute atoms. The effect of migration on the creep ductility of the above materials can be seen from Fig. 1, which

Jan 1, 1962

By I Sherrell, R Jain, P Jansson

With the depleting iron reserves and difficult market conditions, precision in separation efficiency is of utmost importance. Classical local control options are predominant in the industry, but their inability to adjust to resolve application problems of interest has furthered the need of developing and implementing continuous control methodologies.This paper highlights the recent development in control of Outotec SLon® vertically pulsating high gradient magnetic separator (VPHGMS) including programmable logic controllers (PLC) coupled with distributed control system (DCS), on-site human–machine interface (HMI) control panel, advanced process control, continuous online sampling using Courier® 8 and additional modernisation packages including level control and cooling monitoring. These modern control options result in improved efficiencies, promote safer operation and at the same time reduce operational manpower needs.CITATION:Jain, R, Sherrell, I and Jansson, P, 2017. Automation for efficient separation with the Outotec SLon® vertically pulsating high gradient magnetic separator, in Proceedings Iron Ore 2017, pp 211–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Reasons are given for the seemingly excessive public concern with taxation of the mineral industry. Optimality of mineral extraction is a concept that requires careful definition in terms of one or more objectives. Once defined, the impact of taxation upon optimal mineral extraction may be studied; findings from earlier work on this topic are presented for two basically different cases. In conclusion it is observed that the pursuit of optimality requires the availability of highly skilled engineers; in the event of a large-scale mineral development it is this resource that is probably scarcest of all.

Jan 1, 1983

By Albert L. Toenges

The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by: (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war material; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this Critical fuel situation, an investigation was made of possible sources of fuel nearer to points of consumption in New England.

Jan 1, 1948

By R Crookes

Mine to Mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian Mining Industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in NorthernQueensland, Australia, has espoused the Mine-to-Mill concept and isactively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROMstockpile. A blasting improvement program was undertaken betweenErnest Henry Mining, Thiess Contractors and Orica Explosives tooptimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance ofindividual blasts are needed before it is possible to optimisefragmentation or the downstream processes. These include suchspecialised Orica Explosives tools as SABREX, POWERSIEVE, andPOWERLINE and commercially available drill monitors. As importantare the more common still and video camera, borehole loggers,measuring tapes, surveying equipment such as face profilers, and ahigh-speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design - only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as theunderstanding grew and practices have been implemented resulting inreduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution.The continuous improvement program continues...

Jan 1, 2000

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By S. E. Olsen, K. Tang

The complex heterogeneous equilibria associated with the production of manganese ferroalloys have been simulated by employing recently developed thermochemical databases. The non-ideal Mn-Fe-Si-C alloy and the MnO-SiO2-Al2O3-CaO-MgO-FeO slag system have been modelled separately by the compound energy and cellular model. A large number of experimental thermodynamic and phase-equilibrium data were used to evaluate the model parameters for the liquid and solid Mn-Fe-Si-C phases. In addition to the liquid metal phase, solid mixture phases occurring in the Mn-Fe-Si-C system have also been studied. Over 500 measured equilibrium data have been utilised to verify and calibrate the model calculations. The paper will present typical simulation results, from activities of components to multicomponent heterogeneous equilibria. Good agreements can be obtained for many important technological parameters such as carbon solubility, phase relations and equilibrium diagrams, element distribution as function of temperature and slag composition etc. Application of the present models to the silicomanganese production will be demonstrated in this paper.

Jan 1, 2004

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

Distinguished guests ladies and Gentlemen. As many of you know, before I became a Labour Member of Parliament, I had an unusual career path for a politician, in that I spent quite a few years working in the business community. In other words, I was mainstreamed before I was institutionalised. Given that some of this time was spent working for the then Macraes Mining Company Limited, now Gold and Resource Developments NL, I feel that I may have a perspective on how things are seen, on both sides of the fence. In terms of public perception and esteem I am not sure which career option was the step up and which was the step down. So far what I have found very familiar, is that in both roles there is a gulf between the reality and the perception of that reality - a gulf that is both huge and hard to bridge. I think it is a point worth making here amongst another busy industry cluster, that we can all too easily get so embroiled in the day to day activities, that we lose sight of how this might look to those running on a different treadmill. I can still remember scratching my head at the beginning of some days, as I worked to get new mining projects started that I knew were going to bring real jobs and economic benefit to New Zealand, but ending the day feeling like I may instead have been proposing bringing back both strip mining and slavery. If I learnt one valuable lesson out of that time it was this: .... mining has become so publicly demonised on the road to ecological nirvana, that even attempting a lucid dialogue on mining issues, with some, is incredibly difficult.

Jan 1, 2000

By Robert Morgan

With improved methods for designing and detonating shots the potential for flyrock can be significantly decreased, but there are few absolutes in blasting; therefore blasters must learn from the mistakes of others. Blasters must conscientiously employ control measures to minimize the risk of flyrock. The worst case incidents which tend to be widely reported by the media, should serve as a reminder to us all that minimizing the risk of flyrock must be incorporated into the design of the drill pattern and blast design.

Jan 1, 2001