Search Documents

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By Aline Maria dos Santos Teixeira

Serpentinite is an ultra basic and metamorphic rock consisting mainly of magnesium, calcium and silicon oxides. The rock under study is a host rock of chromite mine located in Andorinha, BA. The objective of this paper is to evaluate the rock's physical and chemical characteristics to be used as an additional fertilizer of acid soils. After comminution, rock samples were submitted to chemical analysis, XRD, SEM-EDS and TGA. Afterwards, particle size distribution was determined. Result analysis confirms that our rock consists mainly of dolomite, calcite and diopside. According to the result obtained, it can be said that the serpentinite rock has promising applications in agriculture for the correction and additional fertilization of acid soils. However, it is necessary to study the characteristics of the rock such as its dangers and toxicity as well as evaluate them according to the legislation for corrective acidity.

Jan 1, 2010

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

Despite modest improvements in the performance of domestic interest rates and gross national product,1 fixed investment in domestic producers' durable equipment continued to weaken during the second quarter of 1982 and declined at a 12.8 percent annual rate compared with the first quarter.2 Large declines occurred during the second quarter in expenditures on many of the major mineral-consuming industries such as aircraft, computers, agricultural and construction machinery and mining and oil field equipment. These data appear to be consistent with the low level of business investment plans for 1982 reported in the DOC's Bureau of Economic Analysis survey of expenditures on new plant and equipment.3 Domestic and foreign industrial production and mineral industry production activities continued to decline in the most recent period because of weak demand conditions (Tables 1 and 2). The U.S. mining production index declined 7.7 percent between April and June as compared with 1.2 percent for total U.S. industrial production (Table 1).

Jan 1, 1982

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By H. D. Stolovitch, M. L. Lavallée

"An engineering system used to analyze and improve the performance of industrial grinding circuits has been adapted into a training program. The systematic approach to the design of training was applied in order to:Determine if training was an appropriate and effective tool for the transfer of this new technology;Define the technical content of the program;Establish program specifications based on learner and context characteristics;Design and test prototypes of the instructional modules; and,Establish a strategy for plant implementation and maintenance of the training program.This paper thus describes how a engineering system is transferred to the workplace through the use of designed instruction.INTRODUCTIONTraining can change human performance in a permanent way. It can improve productivity for the overall benefit of an operation. Organizations can therefore use training as a mean to achieve their specific goals. Training is not the solution to every performance problem. However, in many cases, it can be a very effective way to attain desired performance.The benefits of training are often difficult to assess. However, to remain competitive, organizations must introduce new products and innovative technologies. Often, they can do both most effectively through suitable training interventions.In order for the effort and investment of training to provide optimal results, two points of view should be adopted.• An overall view of the system in which training is to be applied.• A systematic approach to the design of training (Stolovitch and Keeps, 1989)."

Jan 1, 1992

By Gerasimenko MP

The authors consider the features and advantages of a new promising trend in mineral processing - column flotation. Design aerohydrodynamic and process characteristics of pilot-scale columns are studied. Optimum process parameters for various ores and operations are studied. Flow patterns in cells of various cross-sections are investigated and the relationship between Peclet criterion and specific capacity of cell is determined. On this basis options were developed for optimisation of hydrodynamic characteristics of large capacity cells, including longitudinal sectionalising of the collection zone. It is shown that advantages of high column cells (10 - 13 m) produced in the West can be implemented in a sectionalised machine of smaller height (5 - 6 m). Investigations on the influence of slurry and air bubbles flow patterns indicated that to increase flotation rate of particles of various flotabilities it is expedient to combine co- and counter-current flows of phases in a single column. The proposed designs allow tailings to repeatedly return tailings to the collection zone and alternate co- and counter-current slurry and air flows. For the first time columns with alternating slurry flows (combination of co- and counter-current flows) are developed and commercialised. Unique multi-sectional cells having a number of essential advantages compared to monocells are developed. Design features of the cell allow: implementation of different flotation process flowsheets in a single unit, improved beneficiation process results, reduced specific power requirement, and elimination of sludging of the aerator and cell bottom part. Operational problems restricting introduction of column cells are connected with the aeration unit. The new cells are supplied with pneumohydraulic and stepped airlift spargers, allowing control of bubble size distribution with a service life of not less than three years. Successful operation of the new generation of columns with cell volumes of 15, 25, 40, and 80 cu m and the height of 5 - 6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants in this country illustrated their considerable process and operational advantages and verified the proposed options and relationships. A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calculating the design of commercial-scale columns is developed.

Jan 1, 1993

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

By K Palmer, G J. Artmont

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because: (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006