Search Documents

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By L. K. Bandyopadhyay

The expert system component of Knowledge Base System supports the analysis and interpretation phases of ventilation design with an algorithmic program used for the solution of alternate design. The paper describes the ?ES-VENT? knowledge based system developed at Central Mining Research Institute, Dhanbad, India for an on-line diagnosing of the ventilation problems using the ?IITMRULE? expert system development tool. In the ?IITMRULE? expert system tool, it has been decided to use a backward chaining reasoning process to reach the goal state i.e. the final conclusion. ES-VENT system is made of three modules: On-line Data, Diagnostics and KBS. Each module is being a collection of several programs. The paper mainly deals with the parameters affecting the ventilation of underground mines such as air-velocity, air pressure, temperature, dust, and humidity and gas contents. The graphical presentation of these parameters on the computer and the interactive part of the developed program is expected to help a ventilation officer to determine the changes in a ventilation circuit necessary to bring the mine ventilation to the desired value. Once such changes are physically effected, the display will indicate if the changes have brought the desired effect or not on ventilation. Keywords: Ventilation network, on-line data, expert system, intelligent system, knowledge base, inference engine.

Jan 1, 2002

Strategic planning in mining is an important value accretive process. One of the most important aspects during the planning phase is determining the correct mine and plant design. The traditional mine site design (mine, plant, stockpiles, dumps) develops a fixed system for one set of conditions or expected values. A robust design is a fixed system that is designed to deal with a large range of conditions without changing the system design. A flexible design changes the system dynamically in response to changes in uncertainties. It is hypothesised that a robust design generates less value than a flexible design as it fails to realise the value of actively managing the operation. One of the most critical aspects in creating strategic value from a project is embedded in the design of the system. A flexible design has components that allow the design of the system to change over time. An operational plan is proposed as a hybrid of a robust and flexible design. This paper seeks to compare these different design methodologies. An analysis of the same case study is undertaken to compare these approaches, showing an a traditional net present value (NPV) of $1678 M, robust design NPV of $1787 M and an operational plan NPV of $1867 M - an increase of $170 M.

Dec 6, 2010

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By David A. Brence, Andrew D. Marti, Richard P. Stahura, Ronald J. Valentine

The development of an effective belt-cleaning system for a new conveyor system seemed a fairly conventional assignment. But a closer examination of the project showed a number of “fine print” details: •High altitude location (with resulting cold weather and low humidity conditions). •Long conveyor length. •Troublesome material (very sticky and capable of hardening like concrete). •Limited water. These difficulties are spelled out the challenge of developing a cleaning system for the production conveyor2 (PC2) belt at Climax Molybdenum’s Henderson Mine.

Jan 1, 2005

By M. Q. W. Jones

This paper summarizes important features of a compilation of thermal properties of stratified rocks from Witwatersrand gold mining areas. The database consists of more than 1000 thermal conductivity measurements, more than 700 density measurements, and nearly 100 heat capacity measurements. Most important rock types and stratigraphic units are well represented. Heat capacity does not differ significantly from one rock type to another, and density is relatively uniform although particular rock types are characterized by distinct average values. Different rock types also have distinct thermal conductivities, but this parameter varies by a factor of four to five. Primary factors controlling the thermal properties are mineral composition, degree of metamorphism, and porosity. In addition, the temperature dependence of thermal conductivity and heat capacity of quartzite may significantly decrease the thermal diffusivity of this rock at deep mining levels.

Jan 1, 2003

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992

By E. Lampard

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety. KEYWORDS Mine plan, mine schedule, variability, safety, lost production, float days, update, adjustment, operations, Maintenance

May 1, 2011

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

In extracting base metals from orebodies, sulphide as well as oxide, the main environmental concern is sulphur, whether in the form of sulphurous gases or sulphate in liquid form. Generally sulphur is in over supply in developed countries mainly because of strict legislation to capture it. In developing countries, on the other hand there is usually a shortage of sulphur because of less strict environ-mental legislation. Africa falls in this second category and the African continent imports substantial amounts of sulphur, despite the fact that large quantities of sulphur are emitted by smelters, thermal power stations, coalmines, fertilizer manufacturers and others. Other than making acid from gaseous emissions, existing methods to capture sulphur from gaseous and liquid effluents are uneconomical and it ends up in the environment either as ammonium sulphate (from gaseous effluents) or as gypsum (from liquid effluents). The CSIR?s Environmentek and Key Structure Holdings have developed a process whereby gaseous sulphur emissions and sulphates in liquid effluents can be economically captured and converted into elemental sulphur and metal carbonates. The elemental sulphur is of high purity as it is precipitated from a gas stream and is readily marketable. The metal carbonates (barium or calcium) can be recycled back to the process or marketed. The only harmful by-product of the process is carbon dioxide. Should natural gas or methane be available, the carbon dioxide could be reduced by about one third. Should solar, wind or hydro energy be available to generate hydrogen, the carbon dioxide emissions would be zero. Employing this technology could make Africa independent of sulphur imports and furthermore reduce the impact of acid rain and seepage of sulphate from gypsum and other waste dumps into the environment.

Jan 1, 2005