Search Documents

By Christopher C. Woomer

Cyprus Shoshone Mine uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. As predicted, severe deterioration of the tailgate occurred in the form of a roof cutter, sloughing ribs, and failing wood cribs. Productivity was affected and additional support was required. Shoshone personnel evaluated several options for providing the additional support needed in the tailgate. The additional support system and placement method had to satisfy several requirements with respect to access, materials handling, placement method, set-up time and support capacity. Approximately 6,000-ft. of deteriorating tailgate had to be supported. The initial wood crib support system left a 6-ft. walkway for access and construction of the additional support. This access was further reduced as the roof loaded the wood cribs. This eliminated the possibility of mechanized material handling to the construction locations. All materials would have to be transported by hand. The additional support system had to be placed quickly to stay ahead of, and keep pace with, the required longwall advance rate. It had to incorporate the existing wood cribs and provide at least 500 tons of extra support capacity. And most critically, the system could not affect longwall ventilation. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as TeksealTM, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the TeksealTM was pumped 900-ft. down the boreholes through a 1.5-in. steel pipe, then as much as 1,800- ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the TeksealTM supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grouts, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous Longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

Jan 1, 1995

By Huang Kai

By adding the solid oxalate acid powder into the solution of nickel chloride or its ammonia coordinated solution, the uniform compound particles were prepared and the precipitated particles were transferred to the mono-dispersed NiO particles by calcination. In this study, the various experimental conditions were investigated, the characteristics of the corresponding obtained particles were analyzed, and the formation mechanism of the particles was elucidated. It was found that the solid oxalate acid provided the solid-solution interface for the precipitation and induced the nucleation and growth of the product particles.

Jan 1, 2005

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By A. Gibson

Most methods for the treatment of scrap printed circuit boards do not reclaim the components in working order as the boards are either fed to a copper smelter, to recover the valuable elements, or, simply landfilled. This work reports the dissolution of the solder in fluoroboric acid containing Ti4+ ions which was particularly selective for solder, allowing the components to be recovered. The solder was subsequently electrowon from the leachant. The boards were then shredded and the copper dissolved in ammonium sulfate and, then treated via solvent extraction to give an electrolyte suitable for electrowinning. The remainder of the metals were dissolved aqua regia, silver remained unattacked by the aqua regia, palladium precipitated as Pd(NH4)Cl6 in the presence of zinc and nickel, the gold was removed by solvent extraction and precipitated as nanoparticles. The aqua regia was then diluted and the zinc and nickel separated by solvent extraction.

Jan 1, 2009

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

By Hisashi Takahasi, Hironobu Yamazaki

INTRODUCTION The slurry shield method was developed in Japan in 1963 and its experimental tunnelling work was performed in 1965. Although the history of this method is short compared with the conventional shield method in Japan, many companies such as Tekken Construction, Okumura Gumi, Nishimatsu Kensetsu, etc. are engaged at present in developing their own unique system of the slurry shield method. The ground of Japan is generally pervaded with ground water and a large number of districts are covered with soft ground, which is composed of fine sand, silt and clay, etc. Therefore, the conventional shield method has always used compressed air with various kinds of auxiliary methods. However, with this method there have been experienced numerous troubles such as ground settlements, lowering of ground water, oxygen shortage within the tunnel, and so forth. The slurry shield method has been developed with the above background. In recent years remarkable progress has been made from the engineering viewpoint in applying this method to driving various kinds of tunnels such as road tunnels, subways, water supply and sewer tunnels, and other tunnels. Apart from Japan, the slurry shield process using bentonite is carried out in England and Germany. OUTLINE OF SLURRY SHIELD METHOD (1) System of Slurry Shield Method Since the conventional shield method drives tunnels using com-

Jan 1, 1976

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By G. W. Harris, J. J. K. Daemen

Slightly shorter, modified version also published in CIM Bull., vol.94, no.1047, Feb. 2001, p.52-55. To minimise ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will allow more accurate location of the grade boundaries on the surface of a blasted rock pile before excavation. A method has been developed and tested for measuring accurately the direction and magnitude of subsurface blast movement, using a caesium vapour gradiometer and a real-time, differentially corrected global positioning system to locate the pre- and post-blast positions of magnetically enhanced target objects placed in blastholes inside a bench. The procedure does not necessitate disturbance of the blasted rock and the movement information is available sufficiently quickly to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m and the overall accuracy was plus or minus 1 m horizontally and 1.2 m vertically

Jun 21, 1905

By Harold J. Miller

Loading and haulage of run-of-mine ore is frequently the highest cost in underground mining operations. These costs can be significantly reduced by use of belt conveyors, a common practice in coal and similar soft miner ii mines. This is particularly true if oversize ore and rock can he eliminated prior to conveying; thus producing a demand for crushers near the production areas. Portable feeder-breakers are extensively used in conveyorized mines, but no suitable, equivalent equipment, is available to provide these benefits to hard rock mines of low to medium headroom. A hard rock crusher capable of easy movement and readily disassembled would allow use to belt conveyors and could improve the general safety and productivity of any underground ore hauling system. This report summarizes proposals and findings made in conjunction with the newly designed M-44 Low Head Portable Crusher which is believed well capable of meeting the requirements of a "portable, underground, hard rock" machine as previously defined in earlier reports. Data gathered by use of the 1/4 Scale Model of the M-44 has substantiated and verified the concept sufficiently to justify construction of a full-size machine for further testing under actual mine conditions.

Jan 1, 1978

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000