Search Documents

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By Christof Metzger

This paper discusses the process utilized by the Kiewit?Bilfiger Berger Joint Venture (Contractor) to select, design, and procure the largest mixshield tunnel boring machine (TBM) ever implemented in North America. The mixshield will excavate the 8,534 linear m × 6.7 m ID (28,000 linear ft × 22 ft ID) tunnel for the City of Portland Oregon?s, Bureau of Environmental Services (Owner) East Side CSO Tunnel Project. TBM selection was conducted under a preconstruction contract in which the Contractor, Owner, Construction Management Consultant and Designer collaborated on TBM selection prior to commencement of construction. This paper focuses on TBM design considerations, including the use of one versus two machines, machine configuration,extended-wear protection, hyperbaric interventions, boulder digestion, and erection of a steel-fiber-reinforced segmental lining

Operations of the new copper smelter at Mount Isa commenced on the 6th February, 1953. Prior to this date a paper by R. V. Anderson (1953) outlined the smelter layout, proposed operation and expected performance.Nominally a 50-ton per day plant, output is currently at the rate of 85 long tons per day. In the first 3t years, of operation to 30th June, 1956, '71,339 tons of blister copper were produced. Operation has been stabilized' and a number of modifications to plant and operation have been made. This paper reviews the progress made to date.GENERAL LAYOUT AND EQUIPMENTThe general layout and equipment follows well-established practice as study of Figs. 1 to 4, and Appendix II will show. This diagrammatic representation of layout (Fig. 1) and flow sheet (Fig. 2) is intended for the purpose of brevity to take the place of a detailed plant description.Choice of site for the smelter was limited by the necessity for close proximity of the waste heat boilers to the powerhouse.Much excavation was necessary before foundation work commenced, but the plant is compact and further expansion is possible.CHARGE MAKE-UPRoaster charge initially comprised concentrates, purchased ores, revert materials, mine sulphide ore and barren sand. As purchased ore receipts increased and as domestic black rock oxidized ore became available, the latter two fluxes were eliminated from the charge. Fluxes at minus i-in. sizing are trucked from crushing plant or stockpile by motor lorries. Filtered mill concentrates are dropped from an overhead conveyor on to the storage patio floor adj acent to the two concentrate bins.

Jan 1, 1957

By H. Moosberg-Bustnes

In cement-based products, such as concrete and mortars, a balance between the particle sizes of the components must be kept in order to obtain the required material properties, such as workability and strength. Sometimes the aggregates lack the necessary amount of fines, hence fine particles, i.e., filler materials, have to be added. Large quantities of filler material are needed in the production of modern concrete types; one principle of self-compacting concrete (SCC) is, for instance, the use of large amounts of fillers to reduce the friction between the coarser aggregates. Use of by-products such as slag, dust or sludge from the metallurgical industries as filler materials in concrete may help to conserve natural resources and at the same time be an economically positive option. However, to be able to successfully use the available materials they must be suitable for the planned purpose, i.e., they must be compatible with cement. In this paper three different experimental studies of steel-slags will be discussed. The aim of the studies has been to investigate if it is possible to improve the steel-slags properties, by selective screening, fine wet grinding or remelting, so that the steel-slags can be used as mineral-addition/filler material in concrete. Keywords: concrete, filler, steel-slag, modification

Jan 1, 2004

By M. Batzle

The upper Arkansas basin has some of the greatest potential for geothermal development in Colorado. Over several summers, students conducted an investigation using seismic, gravity, and magnetics in order to help identify the large structures and basin fill associated with the Rio Grande Rift. Adjacent to Mount Princeton Hot Springs, near surface geophysics was conducted to help understand the faulting and fractures that act as a conduit for hydrothermal flow. The methods used included high frequency 3D seismic, magnetics, gravity, D.C. resistivity, and self potential. Throughout the Mount Princeton area, passive seismic, vertical seismic profiling, and well logging were also used to better understand the geology and activity of the region. The results indicate for the area northwest of the hot springs, a 40 to 50 m thick unconsolidated layer overlying the fractured granitic basement. The DC profile shows a deep geothermal anomaly of low resistivity which correlates with a positive SP anomaly in the same region. In the Chalk Creek valley, a shear zone extends from the north east to the south west, just south of the Chalk Cliffs. There appears to be an upward migration of the water through this shear zone which then flows along the porous sediments towards the south in this area. The deep seismic data collected in the center of the basin suggests that the depth to the basement is approximately 2000m. Also identified on the deep seismic are two major faults on the west end and two minors at the east end of the cross-section. An alteration zone is identified between the faults and a possible Precambrian northeast trending shear zone. The potential for developing an Enhanced Geothermal System (EGS) near the center of the valley is high. Our geophysical results indicate a deep basin fill near the center of the basin providing high temperatures. The range front (Sawatch) fault is observed to penetrate under the center of the basin and is an attractive target for natural fractures.

Jan 1, 2011

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By A. J. Geldenhuys

This paper will focus on two topics, namely (1) an innovative process for the neutralization and partial sulphate removal of acid streams produced during coal mining and processing and (2)optimization of this integrated neutralization process by adding small amounts of synthetic organic polymers. The integrated lime and limestone process has been developed to neutralize acid mine water and to remove sulphate (to less than1 200 mg/l), magnesium and metals. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1 500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. The process consists of the following stages: 1. Limestone (CaCO3) neutralization to raise the pH to 7 and CO2-production. 2. Lime (Ca(OH)2) treatment to pH 12 for Mg(OH)2precipi-tation and gypsum (CaSO4.2H2O) crystallization. 3. pH adjustment with CO2recovered from stage 1 and CaCO3 precipitation. Retention times of 1 hour, 4 hours and 1/2an hour were required by stages 1, 2, and 3 respectively. The sulphate level was reduced to 1 094 mg/l, which is less than the original aim of 1 200mg/l. Chemical costs associated with neutralization, using limestone instead of lime, are reduced by 69% in the integrated limestone/lime process. The overflow water from the clarifier of each of the above stages generally contains a wide variety of colloidal impurities that may cause the water to appear turbid or may impart colour. This results in very slow sludge settling rates that cause overflow water with a high degree of turbidity and colour. There are a number of successive or simultaneous stages involved in the agglomeration of particles. To get optimum neutralisation of the acid water and partial sulphate removal to below the saturation level of gypsum (i.e. 1 500mg/l), maximum sludge recovery is needed. The higher the concentration of seed crystals, the larger the surface area. Therefore, effective removal of suspended and colloidal matter from the overflow of each stage is required and can be achieved by coagulation and flocculation. The polymers PAC6 and 3095 were effectively used as coagulant and flocculant respectively. The addition of these polymers resulted in a clear overflow in each of the above stages with a very low turbidity.

Jan 1, 2003

Predicting Water Recovery from Flotation Cells

Sep 13, 2010

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

The development of research activities at Risdon and the implementing of a policy of instrumentation in plant processes have, in recent years, entailed a considerable increase in research staff and created an urgent need for more space and modern laboratory facilities. The existing laboratories have been in use for 25 years and are now inadequate. New buildings have been authorized.The new buildings will comprise, firstly, a laboratory building of three floors giving a totai .floor space of approximately 11,000 sq.ft., and a pilot plant building as an annexe to the laboratory building, of approximately 4,900 sq.ft. The laboratory building will accommodate from 20 to 22 research workers, and additional plant operatives will be used for the control of processes in the pilot plant building. The new buildings are designed to provide facilities for three principal functions; the investigation and improvementof existing processes, the development of new processes up to the pilot plant stage, and the control and maintenance of instruments.LOCALITY AND ORIENTATION OF BUILDINGSThe site of the buildings is elevated ground on the eastern side of the main plant, near the main entrance and general office building. There will be no obstruction to sunshine at any time of the day, and the laboratory building will command views of wide radius from wooded hills across the River Derwentto the open sea on the south-eastern quarter.The buildings are located to provide space for future extensions. The main laboratory building faces approx...

Jan 1, 1949

By A. Noble

Traditional simulations of mineral processing circuits are solved by straightforward numerical techniques which require iteration to accommodate recirculating loads. Depending on the complexity of the simulated circuit, this solution technique can be inexact, computationally intensive, and potentially unstable. In this communication, an alternate calculation approach is presented, wherein an exact analytical solution is determined as a function of the individual units? separation probabilities. All the stream data, including recirculating loads, may be solved simultaneously, negating the need for iteration. Furthermore, with an analytical solution available, circuit analysis may then be utilized to diagnose the relative separation potential of the circuit. By integrating these tools, the authors have developed a software package for evaluating circuit configurations. This paper presents the theory, development, and limitations of the software?s methodology along with industrial examples which highlight the tool?s applicability to industrial circuits.

Jan 1, 2012

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By Jai Ghosh, Aprad E. Torma, Roger Guay

The catalytic effect of ferrous ion in the industrial biohydrometallurgical heap and dump leaching processes is explained. During the bacterial leaching of metal sulfides, ferric ion will partly be hydrolyzed and a variety of sols, gels, amorphous and/ or crystalline mono- and polynuc- lear hydroxo- and sulfato complex species formed, especially by olation and aggregation reactions. There are many problems associated with these iron precipitates especially in the purification of leach solutions. The present study will discuss the iron precipitation reactions; gives kinetic and thermodynamic evaluations of the effect of temperature on pyrite and ferrous iron oxidation; and reports on the tolerance of heavy metal ion concentrations by Thiobacillus ferrooxidans.

Jan 1, 1989

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014