Search Documents

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By Jean-Michel Rendu

That you are giving the Daniel C. Jackling award to me is a great personal honor. But more significantly, it is a recognition that geostatistics has come of age. And since I am considered by many as belonging to an older generation of geostatisticians, I thought that it would be fitting that I reflect on where geostatistics came from and where it might be going. First, though, let me propose a definition of geostatistics. Etymologically, paraphrasing Webster's definitions of "geo" and "statistics," it is "a branch of mathematics dealing with the collection, analysis, interpretation and presentation of masses of numerical data taken from the earth." This definition is most appropriate in the context of mining geostatistics. It includes both classical and spatial statistics. It emphasizes the earth aspect, or the analysis of geologic features. And it should remind the practitioner that geologic input is a critical part of all geostatistical applications. In the 1910s, statistical methods were already used to analyze geological data. However, the origin of geostatistics, as we know it today, is best set in the late 1940s, when H.S. Sichel recognized the lognormal distribution of sample values in the South African gold mines. In 1951, Daniel Krige observed that "it can be expected that the gold values in a whole mine will be subject to a larger relative variation than those in a portion of the mine." In other words, samples taken close to each other are more likely to have similar values than if taken farther apart. This observation is the foundation on which spatial statistics, which characterizes values defined in a multidimensional space, is built. However, the 1950s were marked by studies based on classical, as opposed to spatial, statistics. It was only in the 1960s that the need was recognized to model the similarity between sample values as a function of the distance between samples and that the semivariogram was defined. A theoretical framework was developed by Matheron that supplied an elegant mathematical explanation to the empirical observations made by Krige. Matheron coined the term "kriging" in recognition of Krige's pioneering work on the geostatistical evaluation of mineral deposits. As soon as this theoretical framework was developed, it was possible to bring geostatistics to the academic world. The "Centre de Geostatistiques" was founded in Fontainebleau. Numerous students were trained there, disciples eager not only to improve the theory and develop more sophisticated mathematical tools, but also to spread the new faith throughout the world. Expansion of geostatistics exploded in the 1970s, arguably the most fertile decade if it is judged by the frequency of theoretical breakthroughs, the number of original publica-

Jan 1, 1995

By A Prinsloo, R Tewu

Automatic control of semi-autogenous grinding (SAG) mills has often been considered complex. Recent experiences at Century Zinc (worldÆs second largest open pit zinc mine) refute this. Together with operating knowledge and appropriate control techniques high quality control is achievable. In this application model-based, constraint, and multiple output control were employed. The control was implemented using standard blocks in the plant DCS. The resulting overall control strategy fulfils the operating objectives and controls the mill with minimal operator involvement over 95 per cent of the time. Previous campaigns using expert systems and complex DCS based control have lacked durability. Their fall into disuse is briefly discussed.

Jan 1, 2009

By Bryan Ulrich

Rroundtable 2009, a Knight Piésold and Co.-hosted roundtable discussion on mine closure and cover design was held at the Red Lion Inn and Casino in Elko, NV on Feb. 12, 2009. Knight Piésold?s Bryan Ulrich and Steve Boyce, as well as Knight Piésold representatives Cynthia Parnow and Corey Conrad from Denver, CO, and Rick Frechette from the Tucson, AZ office were on hand to help facilitate the discussion. The meeting played host to approximately three-dozen attendees from four states. Attendees included personnel from seven mining properties and attendees from corporate offices. The majority of attendees were people directly involved with environmental work on a day-to-day basis. Other attendees were project managers whose jobs involve some level of environmental focus. The purpose of Roundtable 2009 was to exchange ideas and information pertaining to mine closure and cover design associated with almost any aspect of a mining operation. This type of forum provides a less inhibited format for discussion, when compared with traditional conferences and symposia. In the roundtable format, lively discussions are encouraged. This discussion was the fourth in the series of Elko Roundtable events. Previous roundtables pertained to heap leach pad design, construction and operation; design, construction and operation of tailings storage facilities and site-wide water considerations. The initial subtopics for Roundtable 2009 included:

Jan 1, 2009

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

By Tracy Brettmann

Equipment ? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2004

By Johnson T, Huynh D

The State Electricity Commission of Victoria is conducting a program of research and development into alternatives to the use of conventional boilers for the generation of electricity from brown coal. The objectives of the program are to reduce the cost of electricity generation and also to improve the thermal efficiency so as to reduce the emission of greenhouse gases and other pollutants. The program presently includes the following four technologies: Hydro-thermal Drying, Direct Coal Fired Gas Turbine, Integrated Gasification Combined Cycle, and Steam Fluidised Bed Drying. The Hydro-thermal Drying process produces a combustible coal-water-slurry fuel which is suitable for use in a coal fired gas turbine. The coal fired gas turbine has the potential to produce electricity at a lower cost than conventional power stations and when combined with a steam cycle, it will also use significantly less coal. The Integrated Gasification Combined Cycle process gasifies the coal, cleans the gas, and then bums it in a gas turbine/combined cycle. This process is being developed in Europe and the USA in order to meet their stringent emission regulations. It offers Victoria cleaner more efficient and cheaper electricity.

Jan 1, 1992

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By K Ehrig

You are a geologist, geometallurgist, or metallurgist/process engineer and are fortunate enough to work for an organisation who asks you to design/execute a geometallurgy program. What seems like a simple request is actually not a trivial exercise. æRecipeÆ style manuals are not readily available. However, many æexpertsÆ are lurking around willing to deliver solutions which will solve all of your problems. Even though similar ore deposit styles (e.g. porphyry Cu, IOCG, Ni-laterites, calcrete hosted U, etc.) have many similar characteristics, each ore deposit is unique. Hence your geometallurgy program needs to be æfit-for-purposeÆ. This paper offers some insights gained via designing and executing geometallurgy programs from exploration through to production, and working at a mine where you are held accountable for your metallurgical performance predictors.CITATION:Ehrig, K, 2013. Geometallurgy - What do you really need to know from exploration through to production?, in Proceedings MetPlant 2013 , pp 28-33 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J Loimi, P Minkkinen, T Korpela

The head loss caused by metallurgical sampling for slurry streams can be reduced by metallurgical sampler design. When the process volumetric flow rate is reduced by vertical static cutters before the sampling by an equal number of moving cutters to the static cutters, the installation requires less installation head space than other sampling arrangements and is easy to accommodate at suitable locations in the process. Low head loss reduces building costs for the processing plant and operational costs during the lifetime of the plant.The presence of a possible systematic bias in the particle size distribution, solids density and elemental composition between an Outotec MSA 2/50 metallurgical slurry sampler sample and MSA 2/50 manually sampled reject have been studied by a customer. The paired samples were taken as simultaneously as possible. The customer evaluated the possible bias using a paired t-test and provided the assay results to Outotec for further evaluation.The results of the paired t-test showed no systematic bias in particle size distribution, solid density or assayed analytes, except in one analyte with low content and a high relative error. The high relative error in one analyte may have been caused by the same calibration model used in a X-ray fluorescence analyser for both high elemental-content concentrate and very low elemental-content tailings samples. The sampled stream is the tailings of a previous process stage.The results of the t-test were studied further using analysis of variance to reveal the error sources in samples. The results showed no bias between the samples collected from the MSA 2/50 reject and composite samples collected of the MSA 2/50 sample stream. The courier online analyser data was also available for evaluation of representativeness to the process stream.The analysis results of the courier online analysis reveals no bias between the MSA 2/50 reject samples, MSA 2/50 sample stream composite samples and online analysis results during the comparative sample collection period.CITATION:Loimi, J, Minkkinen, P and Korpela, T, 2017. Comparative evaluation of manual sampling and Outotec MSA 2/50 metallurgical slurry sampler, in Proceedings Eighth World Conference on Sampling and Blending , pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By Qing Bo

In this study, the cobalt oxide precursor was prepared in open-style reactor in the condition of high reactant concentration, and then the precursor was decomposed to obtain the cobalt oxides (Co3O4). The effects of some factors on the cobalt precipitation, the particle size and size distribution, and the micro-morphology were addressed. The factors studied include cobalt concentration, initial pH of solution, temperature and time for the reaction, the charge amount of urea, and the temperature for decomposition. It is determined that the precursor particle is in the chemical composition of Co2(OH)3Cl with fine crystalline. By calcinations under proper conditions, the mono-dispersed cobalt oxide particles were prepared with fine crystalline, about 2 µ m in particle size and regular shape in morphology.

Jan 1, 2006

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011