Search Documents

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee' water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

The presence of gold or tin in a particular place in payable quantities may be suspected from geological and prospE;cting reports. It behoves the engineer by judiciously spaced boreholes or pits to establish whether the place is exploitable with profit, and it is the purpose of this paper to set out the ways in which this is done. The various types of deposit to be considered occur in Malaya, Thafland and Borneo, in which countries the writer spent four years in estimating alluvials.The methods described were used in actual practice both by the writer and previous engineers for the same company. The subsequent exploitation of the alluvials evaluated by the methods given below shows that the recovery was as good as, and sometimes higher than, expected. No claims are made to the originality of the methods, but it is 'felt that they may be new to some engineers and< interesting to others contemplating alluvial testing.

Jan 1, 1942

Results obtained from small scale tests using Australian tin concentrates indicate that metallic tin containing less than 0·1 per cent iron can be recovered by a two-stage process using hydrogen and make-up chlorine. In the first stage the concentrate is ground,. pelletized, roasted, and reacted at 650°C with HCI and H2 to volatilize the tin as SnOI2. The volatilization reaction is conducted with cocurrent gas and solids flow because it was found that the use of cocurrent flow yielded a solids residue substantially free from FeCI2. The second stage uses a technique termed "reflux reduction" during which the SnOl2 produced by volatilization is reduced by hydrogen to form tin and a gas containing HCI and H2 of sufficiently high HCI tenor for recycle to the volatilization stage. The elimination of tin ranged from 98+ to 99·7+ per cent of the tin from concentrates containing 5 to 50 per cent tin, respectively. The process should be capable of continuous operation, and a tentative calculation has shown ,that a treatment rate of 12,000 tonnes of tin concentrate per year could be obtained in a volatilization reactor 1·1 m in diameter and 6·1 m high. The process may have particular application to finely divided concentrates containing less than 20 per cent tin.

Jan 1, 1974

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

It has been fairly firmly established (Fisher, N. H., 1945) that the fineness of the gold in any ore deposit varies with the depth from the surface at which the deposit was formed, and, as a corollary to this, that it is dependent upon the temperature and pressure at the time of deposition. This relationship is such that, under certain conditions, the gold fineness, taken into consideration with other recognised criteria, furnishes a very sensitive and reliable guide to the relative temperature of ore formation, at least within the epithermal and the upper part of the mesothermal range.Definition of Fineness.The fineness of gold is calculated in parts per thousand and refers to the proportion of gold present in the naturally occurring metal in the lode, which is actually a gold-silver alloy, containing usually about 10 parts per thousand of base metal and up to 500 parts perthousand of silver. A clear distinction should be made between fineness and gold-silver ratio. The latter refers to the total gold and silver in the lode as determined by assay and is usually expressed as the ratio Au:Ag. Only in deposits where other silver-bearingminerals are entirely absent, which occurs comparatively rarely, can the gold-silver ratio be used as a measure of gold fineness and, in many cases, the two have no relationship. For instance, in the Edie Creek area in New Guinea, the lodes formed under shallow epithermal conditions all carry gold 500 to 550 fine, although the gold-silver ratio ranges from 1:100 to 1:1, in places in adjacent lodes.Determination of Gold Fineness.The fineness of lode gold can be determined only after it has been separated from all other minerals. Amalgamation recovers gold fairly cleanly - unless native silver is present - and the fineness of amalgam bullion is generally a reliable indication of the correct fineness of the gold. If the use of plates is involved, the bullion may be adulterated, but the effect of any copper, or other metal, that may have been introduced can be cancelled by assuming that the gold and silver shouJrl add up to about 990 fine, or by ignoring the base metal content altogether, which varies little in naturally-occurring gold, and in calculating for comparison purposes all fineness figures to the basis Au + Ag = 1,000.The composition of bullion obtained from cyanidation is generally intermediate between the true gold fineness and the total gold-silver proportion as determined by assay of mine or mill-head samples of Cyanide solution dissolves other silver-bearing minerals and the fineness of the resulting bullion is thereby lowered. Consequently, the fineness of cyanide bullion rarely corresponds to the true gold fineness and is useless for diagnostic purposes, although it is a common fallacy to refer to the fineness of cyanide bullion as the fineness of the gold.

Jan 1, 1950

By P. Schilizzi, A. Jarosz, M. Karmis

This paper is concerned with subsidence prediction methods and in particular with two techniques, one based on profile functions and the other on influence functions. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. In more detail, the hyperbolic tangent profile function, as developed by VPI&SU from field data pertaining to the eastern U.S. coalfields, and an influence function method currently being adapted for the same region, are presented and discussed. The applicability, advantages and limitations of these techniques are examined and comparisons are presented with field measurements. Computer software developed for the application of these prediction methods, for two widely used personal computer systems, are also discussed and a number of examples are presented demonstrating the potential of such programs.

Jan 1, 1986

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By Ott F. Heizer

The mines and the mill of the Nevada-Massachusetts Co. are on the east slope of the Eugene Mountains, in Pershing County, Nevada, 8 miles northwest of Mill City, a station on the Southern Pacific R.R. and on the Victory Highway. Fig. 1. Supplies and, concentrate are transported by truck over an automobile road of easy grade. The property is at an average elevation of 5500 ft. and climatic conditions are generally favorable for continuous operation throughout the year. The ore treated is supplied by two adjoining mines, the Stank and the Humboldt. Physical and mineral characteristics of the ores produced by these two mines are substantially similar, although variations occur in hardness and mineral distribution.' The economic mineral is scheelite (CaWO4), composed, when pure, of 80.6 per cent tungstic trioxide (WO3) and 19.4 per cent lime (CaO).

Jan 1, 1935

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939