Search Documents

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

Your Excellency, on behalf of the Council of the Australasian Institute of Mining and Metallurgy, and, indeed, on behalf of everyone present, I extend to you a welcome, and our thanks for your gracious acceptance of the invitation to be here to-day and, later on, to present Honorary Membership Certificates. I also welcome the several official representatives of our Allies, of Great Britain and our sister Dominions.To Messrs. E. C. Driffield and E. J. Rigby, two of the original Foundation Members, who are with us to-day, I extend greetings.The present occasion is opportune to express, on behalf of a representative body of professional men, deep appreciation of the sacrifice which His Majesty the King has made, and will continue to make, by appointing His Royal Highness the Duke of Gloucester as Governor General of Australia and, therefore, His Majesty's senior personal representative in this country.I suppose, that as the primary reason for our assembly to-day is to celebrate the Fiftieth Year of the Institute's existence, I should properly on this occasion, give an account of its history and development. However, as this subject was ably covered by Mr. L. V. Waterhouse, in his Presidential Address in 1938, I trust I may be excused for selecting some other subject. I shall, therefore, exercise my privilege as President and give you a short history of the Mining and Metallurgical Industry of this country with special reference to its effect on the development of the Commonwealth and on the national economy. I apologize in advance for any statistics which I inflict upon you; some of these will be three or four years out of date, because of censorship restrictions. I shall as far as possible refer firstly to the industry prior to and including 1893, the Institute's foundation year, and then to subsequent development.Australia, is pre-eminently a pastoral and agricultural country and it leads the world in the production of wool. Nevertheless, it has an international reputation as a producer of gold and various metals and of minetal products.The development of gold mining in the decade 1840-50 was an epoch-making event in Australia's history, because, to quote one writer's apt phrase, "it precipitated Australia into nationhood." It was certainly responsible for a rapid increase in population. Thus, during the period 1841-1861 the population of Australia increased fourfold, from 221,000 to 1,170,000.The effect of the discovery of gold in Western Australia was even more striking. In 1890 the population of that State was 49,000 and in 1900 it was 180,000.Statistics in respect of gold are reasonably complete, even for the years prior to Federation, and it is interesting to note that the gold declared as...

Jan 1, 1944

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By P. Walford, C. Mealin, D. Good

"The geology of the Ore Fault Ni-Cu deposit has been reinterpreted in the light of recent studies of the geology of the Neoarchean Bird River Sill Complex and the occurrence of economic Ni-Cu and Zn-Cu-Ag mineralization. The Ni-Cu sulfides are hosted by the lower of two parallel NNW-trending and moderately W-dipping mafic-ultramafic intrusions related to the Bird River Sill Complex. The bod¬ies intruded a bimodal volcanic suite consisting of weakly deformed mafic flows and felsic pyroclastic rocks. The mafic volcanic rocks are geochemically related to the MORB-type rocks of the Lamprey Falls Formation, and the felsic volcanic rocks are related to arc-type rocks of the Peterson Creek Formation. The original pyroxene- and olivine-dominated mineralogy of the sills has been replaced by variable ser¬pentine-amphibole-talc-carbonate assemblages.The Ni-Cu sulfide assemblage exhibits textures and geochemical signatures typical of orthomagmatic sulfide mineralization. The sulfide minerals are associated with cumulate layers of magnetic ferrochromite that range in thickness from a few to tens of centimeters. A later event of Zn-Cu-Ag sulfide mineralization associated with quartz veining and garnet-chlorite alteration along a fault that strikes north, dips vertically, and cuts all rock types. The mineralized fault is cut by the NE-trending Peterson Creek shear zone. Where the Ni-Cu and Zn-Cu-Ag mineralized zones intersect, remnant magmatic features such as amphibolite or cumulate ferrochromite bands occur within quartz veins or local chlorite alteration. The mixed zones contain a very unusual polymetallic assemblage of Ni, Cu, Zn, Ag, and platinum group elements (PGE)."

Jan 1, 2009

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By Ogden Malin

IN conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructure of several compositions under various conditions of working were examined in an effort to establish this as a fact.

Jan 1, 1932

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By M Bannear, C Stanton

Since 2008, Arrium has been developing and commissioning a new low-grade hematite ore benefication plant (or OBP) at its Iron Baron mine site.The Iron Baron mine, which was closed in the 1990s, could not consistently yield the high-grade hematite required for pelletising. However, in todayÆs market, the 12 Mt of waste dumps represent a significant low-grade hematite resource, ideal for benefication.Initially, an internal scoping study and several sampling campaigns were conducted to determine the ability to upgrade the available low-grade dump material to a product suitable for export. Test work was conducted at Mineral Technologies (formerly CPG), and included high intensity magnetic separation, spiralling and jigging. Due to promising results from a wet processing circuit, Arrium engaged Mineral Technologies to design a flow sheet that could provide 1 Mt/a of a mixture of high-grade lump (-32 + 8 mm) and fines (-8 mm) products for export.With construction of the plant completed in late January 2012, Arrium, in conjunction with Mineral Technologies, began two commissioning phases. Each phase ended with a toll gate to prove the plantÆs capacity to reach rate and desired grade. After an initial period of running on water, feed solids were introduced to the plant and troubleshooting of bottlenecks began. The first toll gate, whereby the plant was required to run for 24 hours at an average feed rate of 200 t/h (80 per cent of design rate), was completed on the 1 March 2012. Further troubleshooting and resolving of issues allowed the plant to steadily increase feedrate while maintaining good availability and grade. The second toll gate required the plant to run for 72 hours at an average feed rate of 200 t/h while meeting grade, yield and water consumption targets. Sampling campaigns were conducted during this period to track the performance of key equipment. Completion of the test, and full handover of the plant to Arrium, was completed on the 21 April 2012.Although the formal commissioning phases had been completed, ongoing optimisation of the OBP continued, ensuring that all major equipment was working to produce the optimum yield and grade. Sampling campaigns were conducted on the jigs and spirals, with results and correlations used for operations documentation.Overall, with successful completion of the final acceptance tests, the commissioning of the Iron Baron OBP has been established as a major success achieving all production and quality targets as per the original design intent.This paper will focus on the successful commissioning and ramp-up performance of the plant however reference will also be made to the key development stages involved with the development of the project.CITATION:Stanton, C and Bannear, M, 2013. ArriumÆs Iron Baron hematite beneficiation plant - a success from start to finish, in Proceedings Iron Ore 2013 , pp 547-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

Pressure for Better Safety Practices ? Increase Government Regulation ? Safety practices evolve from: ? Increased efficiency and performance ? More knowledgeable workforce ? Focus on decreasing risk to shareholder value In Order to achieve this ? Focus Points: ? Skill Development ? Best practices ? Situation-based decision making ? Enablers: ? Adoption of new technologies ? Transformed miner education ? Delivering on-demand information to the point of work Results: Miners empowered to improve mine safety

Aug 1, 2013

Used in conjunction with geology and geophysics, geochemistry provides powerful exploration tools of special relevance to Australian environments. New methods are needed that will confront the forthcoming emphasis on locating concealed orebodies. Deep weathering is conducive to techniques using groundwaters or gaseous emanations as sample media. Increasing use is anticipated for isotope measurements and for recognition of country rock characteristics that denote proximity to mineralization. Improvements in the sensitivity, reliability and portability of analytical instruments will underpin the contributions of geochemical methods to future mineral exploration.

Jan 1, 1982