Search Documents

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By Enrique Mansilla Navarrete

El presente texto describe las investigaciones recientes sobre el uso del caolín como "rellenador" en las diferentes industrias y artes. Los "rellenadores" o "fillers" son materiales qúimicamente inertes, cuya acción es básicamente física. Entre las características de los "fillers" tenemos la densidad aparente, tamaño de partículas, capacidad de absorción, abrasividad, porosidad, comportamiento térmico y una velocidad de sedimentación adecuada. De acuerdo a estos parámetros señalados, se desarrolla un programa exploratorio, los métodos empleados y la descripción de su uso en algunos depósitos encontrados en Cajamarca.

Nov 8, 1982

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company's Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

By D. Arku

The increased use of sensors to facilitate automation has led to an explosion of data. As data sets grow in size, their use becomes more complex. Therefore, there is an incentive for reducing the size of the datasets, as long as this does not compromise information gleaning. With this in mind, this project explored basic aggregation as a viable alternative to amassing large amounts of data. The goal of the project was to determine if one would arrive at different conclusions had they analyzed aggregated data instead of raw data. In a mine, operational data is typically used for tracking process statistics, correlation between factors, autocorrelation and multivariate models (for a factor of choice). Therefore, this project compared results from such analyses when it was conducted with aggregated data (AD) with the results of analyses conducted with raw data (RD). The data consisted of one-minute-apart readings from a semiautogenous grinding (SAG) mill on the horsepower, feed rate (tons per hour), rotations per minute (rpm), noise, recycle (tons per hour), density (% solids) and bearing pressure (psig). This data was aggregated by averaging five and 10 continuous (one-minute) observations. Changes in statistical measures between the two approaches were typically within 5% of each other. Differences in correlation coefficients between RD and AD(s) were also within this range. Autocorrelations present within RD were preserved in AD, as long as the time lags were scaled for the amount of aggregation. Regression and neural network models were also developed for power consumption. The prediction performance of developed models was similar whether one used raw data or aggregated data. Overall, it appeared that aggregating the data based on 5- or 10-minute time spans would not have resulted in conclusions (from simple or complex analyses) being different from using raw data. In other words, whether one had used raw data or aggregated data, the conclusions would have been the same, suggesting that time domain aggregation, a common industry practice, is a good alternative to storing high-density data in this case.

By Brommerm Tracey, Britt Elin Gihleengen, Elsa Olivetti, Hans Ole Riddervold, Randolph Kirchain, Geir Øyen

"Compositional uncertainty in secondary materials and variable processing conditions inhibits secondary material utilization in the production of aluminum alloys. Efforts to implement optimization models that direct batch planning have limited industrial presence due to factors such as the insensitivity of these optimization models to dynamic plant circumstances. This paper describes a chance constrained model formulation that generates lower cost, robust batch plans with significant flexibility towards changes in processing conditions. The principal attribute of the chance constrained formulation is its inherent mitigation of risk by diversifying the batch plan. This paper compares aluminum remelter batch planning using the chance constrained formulation with a traditional deterministic model and a manual batch planner. With the expectation that volatile material prices, restricted scrap material availability, and pressure by consumers and legislation for increased recycled raw material input will continue in the future, batch planning tools that inherently diversify a production portfolio will become increasingly advantageous for industrial aluminum remelters.IntroductionAluminum remelters must develop strategies to incorporate lower cost secondary materials into finished alloys to remain competitive amidst increasingly demanding market and regulatory conditions. Determining the optimal combination of incoming raw materials to produce an alloy that meets compositional specifications presents remelters with a complex problem that has driven the development of computational tools commonly referred to as batch planning or blending algorithms. The ubiquity of the ingredient or raw material blending problem in production has motivated ongoing development of batch planning algorithms since the classic nut-mix problem in the 1950's [1]. The most common model formulation for industrial aluminum remelters are deterministic, linear optimization programs [2]. These blending problems determine the optimal combination of raw materials by minimizing cost subject to constraints around demand, availability, and compositional specification. Despite extensive research and moderate computational requirements, batch planning algorithms are inconsistently used in industry. Insufficient incorporation of the complexity of real world remelting conditions into these models provides an obstacle for their implementation [3]. For example, many batch planning algorithms do not explicitly incorporate the impact of compositional variation of the raw materials on overall batch cost. Additionally, they do not allow for endogenous specification of tolerance to error in batch planning, so provide little flexibility where a batch planner would like to incorporate materials of greater uncertainty. Incomplete accounting for quality variability undervalues secondary materials leading to overly conservative use [ 4, 5]."

Jan 1, 2011

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation's last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell's throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954

By George W. Bain

Mr. Geo. W. Bain: Dr. H. C. Cooke's discussion of 'The Geology and Mineral Deposits of the Harricanaw and Bell River Basins' possesses many of the elements of a good political address; perhaps his long residence in Ottawa has some bearing upon his method of discussing geological work. The three essential parts of the address are all included. First, the plank - "Contributed discussion on the Geology and Mineral Deposits of the Harricanaw and Bell River Basins"; second, the personal attack upon the opponent, to show antipathy to the opponent as well as to his ideas; and third, controversion of a number of statements, which have been made to appear as planks of the opponents platform, even statements and work which are in no way connected with one under discussion. In the following pages, I will confine my attention to a defense of my work in the Harricanaw and Bell River basins, leaving discussion of the other areas mentioned by Dr. Cooke until results of the re-surveys are published. It is intimated that it was impossible to make a geological examination of an area of 1,600 sq. miles on a scale of four miles to the inch (base map supplied) in three and a half months, because "the area is accessible only from the railway along the northern edge together with a few roads close to it, and from rather wide separated streams?. There is one way, known to most geologists, whereby a place can be reached other than by railway coach or motor boat, and that the oldest of all -- walking. Most of the region was reached in this fashion. The boundaries of all the 18 townships included in the map are surveyed, nine are divided into lots, and the north-south and east-west centre lines of most of the others are surveyed and have mile-posts placed.

Jan 1, 1927

By J. M. Kuchta

The Bureau of Mines investigated four simulated coal gob fires to obtain a more reliable data base for defining the state of a sealed mine fire and to evaluate the performance of various fire detectors. The fires were conducted in a multiple-entry section of the Bruceton Experimental Mine by heating 4,000 to 21,000 pounds of rubblized bituminous coal to ignition and monitoring the temperature, gas emissions, and smoke under ventilated and sealed combustion conditions. Product gas concentrations depended upon the coal bed size, coal temperature, heating rate, and oxygen concentration or ventilating condition but varied little after the fires were sealed. Expressions are given that define the temporal variation of CO and O2 after sealing when the coal temperature decreased rapidly. The CO/C02 ratio is a more sensitive fire indicator than the CO/?02 ratio, although the latter is universally used for detecting the incipient state of a coal fire. In comparison, the Jones-Trlckett ratio [ CO2 + ¾ CO ? ¼ H2 ?O2] is less reliable for this purpose. The best detector for determining the state of a mine fire after it has been sealed was a prototype submicrometer smoke particulate sensor. Limitations of the various detector systems are also discussed.

Jan 1, 1982

In the flotation of fine particles, problems arise which do not occur with coarse-ground pulps. For example, the presence of colloidal or near-colloid- al gangue particles gives rise to ex- cessive entrainment in the froth, with reduced grade as a consequence. If the values themselves are finely dissemi- nated, the recovery usually decreases as the particles diminish in size, so a low recovery is combined with poor grade. Sutherland and Wark (1955) referred to the complications arising from the presence of fines, indicating (p.382) that fine grinding "introduces diffi- culties that have not yet been satis- factorily overcome". At the time of writing, very little work has been done on fines flotation specifically, yet the groundwork has been well laid. The availability of better scientific instruments, together with the general advance of understanding in a wide variety of relevant research fields, has taken us a long way toward finding the reasons behind the problems as- sociated with fines, and also toward finding practical solutions. It would be useful to define what is meant by "fine" particles before going further. To some extent, the definition is somewhat elastic as far as flotation is concerned, because the density of the particles has a bearing on whether or not they act as fines. But in general we are dealing with particles less than about 20 pm in Diameter.

Jan 1, 1984

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By Will H. Coghill

This paper on milling methods and costs at a flat river (Mo.), mill is one of a series of information circulars on milling methods and costs which is being prepared by the United States Bureau of Mines, The mill under consideration treats 5,000 tons of load ore daily by table concentration and flotation. It is 25 years old, and yet it is a new mill. Research has been in continual progress at the plant since its beginning, and accordingly a day never passes without a record of change for advancement. The changes have been so orderly that no evidence of obsolete equipment remains.

Jan 1, 1932

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

The Sishen iron-ore-mine produces 3 pro= ducts with size gradings of 25 to 8 mm, 11 to 5 mm and 5 to 0,2 mm and has a product capacity of 20 Mtpa. Ore is produced at an average Fe content of 66,2 % Fe for the two coarser pro= ducts and an average of 65,3 % Fe for the fine ore product. Three stage crushing is practised to re= duce the run-of-mine ore to -90 mm after which it is screened into five different size frac= tions of which four are heavy media beneficiated in static baths and cyclones and the fifth frac= tion discarded to slimes dams. A final three stage crushing and screening process is employed to produce the final three Products which are homogenized by means of blen=ding systems nrinr to despatch.

Jan 1, 1987

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By Frederick W. Horton

The lack of comparable and accurate statistics of coal-mine accidents in the United States as a whole led the Bureau of Mines in 1911 to undertake the collection of such data. The importance of such statistics as a basis for remedial legislation can not be overestimated, moreover they serve to indicate the results of the efforts made by the Federal Government, State mining departments, and mine operators throughout the country to lessen the hazard of coal mining. The mining departments of the leading foreign coal-producing countries have long taken cognizance of the importance of such statistics. In Great Britain, official statistics of coal-mine accidents have been collected and published since 1851, in France since 1853, in Austria since 1875, in Germany since 1852, and in Belgium since 1831. The United States not only leads these countries in the production of coal but the output of its coal mines is greater than those of Great Britain, France, Belgium, Austria, India, Japan, and New South Wales combined. Accordingly, it is proper that there should be some official record of the accidents in this, the greatest mining industry not only in the United States but in the world. It is especially appropriate that this work should have been undertaken by the Bureau of Mines, as, through its investigations of mine accidents in the field, it is constantly in close touch with coalmining conditions throughout the country. Its engineers are not only able to obtain first-hand information as to a great many accidents, but, through their special training and experience, are able to appreciate the significance of the figures reported by the coal-mine operators, thus aiding an intelligent and uniform classification 01 the accidents for the country as a whole. Further, the State mining dnpartments and State mine inspectors of every State in the country having a system of coal-mine inspection are cooperating with the bureau by sending it monthly reports of accidents in the coal mines of their respective States. The receipt of such reports places the bureau in a most advantageous position to publish promptly statistics of these accidents. Although a few years ago accurate statistics of c~al-mine accidents in the United States as a whole were entirely lacking this bureau was able to pubjiish the 1912 statistics within three n:onths after the close of the year and long before corresponding statistics had been issued by the mining departments of the leading foreign coal-producing countries. The cooperative agreement with the State coal-mine inspectors has not only made possible the prompt publication of the statistics, but it has also enabled the bureau to classify the fatalities by months and according to cause, showing the months in which the greatest and the least number of men were killed and from what causessomething that has never before been accomplished for this country.

Jan 1, 1913

By W. Geo. Waring

THE growing need of better methods for the recovery of zinc and other elements from complex sulfide ores has suggested an inquiry respecting a possible group separation of the elements by the aid of volatilization at more or less elevated temperatures. It 'is evident that if the zinc content of such ores can be completely separated, for instance, as pure oxide, by a volatilization 'method, there should be no difficulty in recovering the other elements by smelting and refining. Zinc burning" as applied to zinkiferous ores has advanced but little in practice since the invention of the wetherill grate-furnace process in 1852, as may be seen by reference to papers on the subject.' In other words the thermochemical reaction employed in effecting the volatilization of the zinc is essentially one of reduction by means of carbon, whether the ores treated contain their zinc in an oxidized form, or as the sulfide. The zinc vapors, liberated from the ores at a temperature above that required for the reduction of ZnO by C (about ,1100° C.) or for the volatilization of ZnS per se, (about' 1300°-1400° C.) are subsequently burned to ZnO or to ZnO + SOz, by contact with' atmospheric ,oxygen in the upper or posterior parts of the furnace chamber, or in a so-called "combustion chamber" after leaving the .furnace proper.

Jan 1, 1925

By Fábio de Oliveira Braga

A proteção balística contra projéteis de alta energia, como o 7,62 mm, é mais eficientemente realizada por meio de sistemas de blindagem multicamada (SBM). Estes são formados, em geral, por uma camada frontal de cerâmica, uma camada intermediária de tecido sintético ou de compósito, e uma camada posterior de um metal dúctil. Em trabalho recente, Monteiro et al. (2016) estudaram um SBM com camada intermediária formada por compósito reforçado com tecido de rami em substituição a um laminado tecido de aramida. Eles obtiveram resultados satisfatórios com boa redução de custo. No presente trabalho, foram investigadas fibras de rami in-natura como substituição ao tecido de rami na camada intermediária compósita. Os resultados foram comparados ao desempenho de um compósito reforçado com 30% de tecido de aramida, bem como aos resultados anteriores. Observou-se que a utilização dos compósitos reforçados com fibras de rami manteve o bom desempenho do SBM, com um custo cerca de 5 vezes menor que o SBM com aramida, e 60% menor que com tecido de rami.

Oct 30, 2017

The statistical nature of the variability in detonation times of pyrotechnic delays is discussed, and how to evaluate the probability of required detonation intervals is shown. Some methods (analytical and stochastic) are given for designing blasts to ensure that any adverse effects on the variability in the delays is taken into account and minimised. Using computer models of blasts, detonation simulations can be used to check the initiation sequence for the probability of sequence reversals, indicating areas of high blast damage potential. Charge consumption rates, which relate directly to the resulting vibration levels, can be examined for their susceptibility to variation from delay variability. Models that synthesize vibration waveforms for production blasts, when taking delay variability into account, indicate the difficulty in vibration level prediction.

Jan 1, 1992