Search Documents

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By Richard F. Link

The objective of this report is to explain a statistical method for the summarization, organization, and classification of multivariate assay and other data from the mineral industry. Multivariate data are those characterized by several measurements at each data point, such as assay data from a mixed metal mine, or blast furnace data. A specific method of linear discriminant analysis, the Mahalanobis d2 procedure, is explained, starting from elementary principles; the d2 procedure enables many measurements at many data points to be studied by investigating the interrelationships among the data. The relation of linear discriminant analysis to other statistical methods for treating multivariate data, in particular the eigenvalue technique of factor analysis, is also explained. Example analyses are made on data from the Frisco mine, San Francisco del Oro, Chihuahua, Mexico. The data comprise assay values for silver, lead, copper, and zinc taken at some 19,000 sample points distributed into 91 groups.

Jan 1, 1967

Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSE ' 1919 " 1920 W. H. BASSETT 1921 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. K. ELLIOTT 1925 " F. JULIUS FOHS 1921; PAUL D. DIERICA " 1927 JOHN M, LOVEJOY 1928 S. SKOWRONSKI A. W. AMIBROSE RALPH Fl. SWEETSER 1929 " J. B. UMPLEBY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN \V. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. AT. BECRET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR , C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNER 1934 .J. L. CIIIRISTIE H. D. WILDE, .JR. L. F. REINARTZ T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H, DOLBEAR 1936 E.H. DIX,JR. HALLAN, N. MARSH C. E. WILLIAMS EUGENE McAULIFFE WILLIAM B; PLANK' OLIVER BOWIES 1937 A. J. PHILLIPS AL ALBERTSON FRANCIS B. FOLEY J. B. Moscow " CHESTER A.. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOALSON J. R. THOENEN 1939 R. H. LEACH W. I-1. G E I S J. HUNTER NEAD C. A. GIBBONS " AT. M. LEIGHTON 1940 C. A1. WISE T. V. MOORE F. T. SISCO C. E. LAWALL W. R. CHEDSEY W. M. WEIGEL 1941 D: K. CRAJIPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " . PAUL AT. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER 1943 CYRIL STANLEY SMITH C. A. WARNER HERBERT W. GRAHAM CADWALLADER EVANS, JR. " HOWARD 1. SMITH 1944 ARTHUR PHILLIPS W. S.-MORRIS WILLIAM A. HAVEN A. W. GAUGER A. C. CALLEN C. H. BEHRE, JR

Jan 1, 1944

By V. E. Dementyev

This paper presents a brief overview of some IRGIREDMET advances in gold hydrometallurgy. Original impulse-percolation technology and equipment for intensive cyanidation of gravity concentrates have been developed and introduced into industrial practice by IRGIREDMET since 1980s (RF Patents N1593250). The process is based on leaching using special hydrodynamic and reagent conditions providing high dissolution rate for coarse gold particles. Gold and silver are precipitated from pregnant solution by cementation or electrowinning. There was also proposed an im-proved cementation method using zinc in a contact with electrically conductive material. The units including closed water recirculation, tails detoxification and semi-dry tails IRGIREDMET is well experienced in gold adsorption technology using ion exchange resins and activated carbons. The comparison of CIL and RIL processes were done for a number of gold mines, for example for Sukhoi Log gold deposit. The properties of prospective foreign and domestic ad-sorbents including strong-base, bi-functional and weak-base resins as well as activated carbons were studied. The Institute has developed some adsorption/elution technologies and equipment, such as a two stage RIP adsorption technology for gold/silver ores, an improved technology for gold elution from loaded resin and carbon, electrowinning cells for gold recovery from RIP and CIP eluates etc. Large scale ?Resin In Pulp? tests using weak-base resin were finalized and process design criteria were developed. Gold plant design is on progress at the moment. Improved technology for carbonaceous (preg-robbing) gold ores was developed. It was tested for some gold deposits including Sukhoi Log. It allows to overcome preg-robbing activities of ores treated and to improve dramatically performance of cyanidation and adsorption circuits. The studies on refractory gold ore treatment including bio-oxidation, pressure oxidation, roasting and ultra-fine grinding were conducted. Heap leach technology was tested and introduced by Irgiredmet for a number of Russian mines. Zinc cementation, activated carbon and ion-exchange resin adsorption were used for gold recovery from pregnant heap leach solutions. The options including combined technology ?Heap leach/ RIL or CIP? for clay ores were also developed and tested. The plant using developed technology is at construction stage now. The study on In-Situ gold leaching was conducted. The comparison of different gold lixiviants for this purpose was carried out. Gold recovery from pregnant leach solution by activated carbon and anionite including gold elution from loaded adsorbents etc. was also studied. In 2000 the In-Situ leaching technology was commissioned at Maminskoye gold deposit (Ural). The technologies for treatment of complex ores and by-products were proposed. For example, the technology of gold, silver, copper and zinc recovery from calcines after sulphuric acid production was developed.

Jan 1, 2014

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By X. Q. Cui

The surficial collapse pits of the mining areas are continuously spreading in Beiminghe iron mine of Hebei Province as a result of the exploitation, which has done a lot of damage to the circumjacent ecological environment of the mine. It is a new path to handle the mine tailings at the present time that the thickened tailings are used to backfill the collapse pits, in which way the problems of the surficial collapse and the nowhere discharge of the tailings are both solved, and the rational utilization of the mine tailings and the clean production of the mine enterprise are realized. The?200 mesh content of the tailings of Beiminghe iron mine is 76.87%, and?325 mesh content is 63.50%. Semi-industrial dehydration experiments to the tailings have been done using the hydro-cyclone classified thickening process. The results show that when FX125 hydrocyclone is adopted, the concentration of underflow can achieve 73.31%, and the yield ratio is 61.78%; when FX150 hydrocyclone is adopted, the concentration of underflow is 70.57%, and the yield ratio is 54.31%, which indicate that the minor diameter hydrocyclone is propitious to improve the yield ratio of the underflow. The semi-industrial dehydration system of hydrocyclone classified thickening process is com-posed of FX125 hydrocyclone, D3600 high-efficient thickener and D2000 thickening bucket. The capacity to tailings disposal can achieve 3.07t/h and the tailings can be thickened from 28.86% to 62.45%. Compared with the traditional thickening-filtrating process and the total tailings directly filtrating process, the hydrocyclone classified thickening process has the merits of simple flow and high thickening efficiency, so it is easy to be realized in the mine.

Jan 1, 2014

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

By B Reid

"Since the commencement of mining operations at the Cowal Gold Operations (CGO) in 2005, reverse circulation (RC) drilling has been the preferred method for grade control (GC) sample collection. This method was selected because it allowed:for multibench drilling (20 m hole depths for two benches of mining) to aid mine planning increased data density for comparison against the wide spaced ore reserve model angled drill holes to intersect perpendicular to the strike and dip of the shallow dipping mineralisation ability to take two metre sample intervals to enhance the understanding of the mineralisation’s short-scale variability and provide the ability to flitch mine.From June 2008 to December 2013, RC GC was performed using a UDR rotary cone splitter. The field duplicate data over the period displayed strong precision, with a correlation coefficient of 0.94 and an average relative per cent difference (RPD) of 21 per cent for gold. Up to 66.1 per cent of field duplicate data greater than 0.1 g/t fell within ±20 per cent RPD. This is within limits of industry best practice. The Mine to Mill reconciliations over the same period showed the estimated GC grade was 7.7 per cent lower than the calculated head grade (CHG).In December 2013, the Progradex sampling system (PGX) was introduced at CGO due to its advertised ability to capture 100 per cent of the drill cuttings for the complete sample interval, inclusive of fines. Analysis of field duplicate data indicates that since the introduction of the PGX, the sample precision has drifted. From January 2014 to February 2016, the correlation coefficient was 0.92 and up to 51.2 per cent of field duplicate data, greater than 0.1 g/t fell within the ±20 per cent RPD. Over the same 26 month period, the Mine to Mill reconciliation improved to one per cent lower than the CHG. Granulometric analysis of the RC samples collected from the PGX indicated the fines material(<212 µm) averaged up to 22 per cent of the samples mass and following assay determination, the fines material represented a weighted average of 31 per cent of the total gold content within the sample.This paper highlights the:importance of the complete capture of all drill cuttings during an RC drill programinfluence of fines material on the sample quality and accuracyimpact sampling of the fines material has on the Mine to Mill reconciliation performancechallenges experienced in commissioning a PGX system.Citation:Reid, B, 2016. A Fine Looking Sample - the Importance of Fines in Grade Control Sampling to Mine to Mill Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 28–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements. REEs are used widely in high-technology, clean-energy products as well as weapon systems. China's dominant position as a producer of over 95% of the world REEs output and the world's increasing reliance on REE products have highlighted concerns about the future availability of rare earths in recent years. This paper briefly reviews the REEs world reserves, production, consumption, the impact of our heavy reliance on REEs products and China's changing policies on REE export on world supply chain.

Jan 1, 2013

By C. E. Rodgers

WHEN I was asked to prepare, for presentation at the 1938 Annual Meeting of the Institute, some data concerning low-discharge grinding at the Sylvanite mill, it seemed entirely reasonable to expect to have at my disposal the results of at least four full months' operation after the last unit, as then proposed, was installed. Delays in delivery of equipment, nevertheless, shortened the interval, as will be shown herein. In submitting the data contained in this discussion, I wish distinctly to state that the intention is not to claim that final conclusions can be reached at this time concerning our operation. Test periods, in certain instances at least, have been too short for this purpose, although some, where so stated, have been extended through March and April. It is hoped, however, that an advantageous trend in practice can be shown and that the experience related may be of interest to others who are now operating, or who are considering the operation of, low-discharge grinding mills. In the plant under review, four mills are in use: one primary and three secondary. Present mill capacity (grinding, as shown by screen test, about 99 per cent through-200-mesh and approximately 88 to 89 per cent minus-325-mesh with infrasizer giving about 90 per cent of the latter) averages about 525 tons per day. A brief description of each unit will be given and comments will also be made relating to operation. This will be followed by certain test data from which, in conclusion, operating results are summarized.

Jan 1, 1938

By I. Filzwieser, A. Filzwieser

The Peirce Smith converter is the key metallurgical vessel in the majority of copper smelters. During the two step process, oxygen enriched air is injected through a row of tuyeres into the matte received from a primary smelting unit. Additionally, in the first step the iron content is oxidized into a fayalite slag by the addition of silica. During the second step, the remaining copper sulphide is converted into blister copper with a final sulphur content of approximately 200 ppm. The overall efficiency of this process is determined by the total reaction time, the slag quality and quantity, and the chemistry of the final blister copper. To increase the reaction kinetics during both stages, the METTOP Process Control and Regulation (MPCR) system was developed, which consists of four elements: OPC - Optical product control ACR - Automatic computer regulation GCU - Gas control unit GIS - Gas injection system The OPC system from SEMTECH records the optical spectrum emitted by the off gas flame providing immediate, detailed process information. Using this online data, additional gas can be automatically injected into the converter through a gas injection system opposite the tuyere zone. An improved oxygen distribution in the melt and the accurate determination of the process end point results in a significant reduction in the process cycle time. Furthermore, by maintaining the reaction closer to the equilibrium the final sulphur and oxygen content can be reduced compared to the conventional process. In particular, the final sulphur content can be lower than 70 ppm, eliminating the need for an oxidation step in the anode furnace.

Jan 1, 2007

By Allan P. Fawley

ONE hundred miles from Vancouver, at an elevation of 4,000 feet, is the Pioneer mine. It is situated on Cadwallader creek, a tributary of Bridge river, and is reached by travelling from Vancouver to Squamish by boat, a distance of thirty-two miles, from there by train to Bridge River (one hundred and seven miles), and finally by automobile across Mission mountain .(7,000 ft. elevation) to the mine (fifty-six miles): a total distance of one hundred and ninety-five miles. Prior to 1924, many Companies had examined the Pioneer, which had been developed by shaft to a depth of 200 feet, but, while values were good, the small size of the ore-shoot discouraged large investors. In July, of that year, opera-tions were re-commenced by the late David Sloan and, on sinking further, the ore-shoot was found to lengthen greatly as well as to ex-tend in depth, while remarkable gold values also were encountered. When, later, the price of gold rose from $20 to $35 per ounce, the mine was in an excellent position to take full advantage of the increase + and not only became an extremely profitable enterprise itself but its success greatly stimulated the search for and development of other 1-gold properties in British Columbia.

Jan 1, 1937

By Groom P.

Discussion of the paper presented at the Midland Institute of Mining, Civil, and Mechanical Engineers' general meeting held in Leeds, March 21st, 1916, with T. Beach, vice-president, in the chair included contributions by Beach T., Fearnsides W.G., Lloyd W.D., Gill J. and Nadin R.

Dec 1, 1916

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976