Search Documents

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By L. D. Snyder, J. K. Russell

"The Lower Jurassic Iron Mask batholith intrudes Upper Triassic Nicola Group volcanic rocks in the Quesnellia terrane of southcentral British Columbia and hosts Cu-Au mineralization. The batholith comprises three mappable intrusive phases, including: Pothook gabbro to diorite, Cherry Creek monzodiorite to monzonite and Sugarloaf diorite. The Iron Mask hybrid forms a fourth mappable unit that makes up to 45% of the areal exposure in the batholith. It is highly variable in texture and composition and subdivided into three types; Type I and II have abundant (partially digested) xenoliths, many of which are derived from the Nicola Group, whereas Type III is xenolith-poor and shows extreme outcrop-scale textural diversity.Pothook and Cherry Creek rocks are similar in texture, mineralogy, whole rock and mineral composition and style of alteration. Contacts between the two can be intrusive or gradational. Rocks collected from these two suites have compositions that are permissive of a single magma batch, although simple crystal fractionation does not explain all chemical variations within and between the two suites. The Sugarloaf unit comprises a diverse group of amphibole-phyric rock types and is texturally and mineralogically distinct from Pothook and Cherry Creek suites.The Iron Mask hybrid represents progressive stages of physical and chemical interaction between Nicola Group country rocks and Pothook magma. Magmatic assimilation (selective or partial) is supparted on the basis of field relationships, petrographic observations, and REB compositional data. Thermal dehydration and partial assimilation of Nicola Group rocks by Pothook magma is shown to be a valid means of promoting early and extensive volatile saturation in the Iron Mask batholith."

Jan 1, 1995

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By G. F. Joklik

Although the mineral shortages of twelve to eighteen months ago have given way to oversupply, their memory lingers on. These problems were man-made: booming demand throughout the industrial world, political and industrial unrest and the oil embargo all contributed. But in the minds of many, the shortages conjured up visions of the depletion of the world's mineral resources, a disaster that could be staved off only by drastic curbs on consumption and therefore, curbs on economic growth. A little historical research shows that fears such as this are not inventions of the 1970's. A hundred years ago, for example, the imminent exhaustion of the world's coal supplies was being predicted in Great Britain. The English economist, John Stuart Mill, who was usually more perceptive, wrote a few years earlier that "it is only in the backward countries of the world that increased production is still an important object". And later there was Franklin Roosevelt who said in 1932, "Our industrial plant is built; the problem just now is whether under existing conditions, it is not overbuilt". His concern, in other words, was not with the discovery and exploitation of new natural resources, but with the administration of known resources and with seeking foreign markets for surplus production. In light of copper prices at the time -- just under 6¢ a pound -- that was understandable. These instances illustrate how, throughout the world's industrial history, concern about surpluses of raw materials has alternated with alarm about the adequacy of supplies and with calls for restricting growth.

Jan 1, 1975

By S. Chama, K. Nyirenda, J. Machona, P. W. Chishimba, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

Our study focuses on upgrading of copper and cobalt from the Democratic Republic of Congo tailings, containing 2 wt% Cu and 0.5 wt% Co. Cobalt is in the complex iron silicate matrix such that its recovery by direct leaching is not possible. Two concentrating methods were employed in order to obtain copper and cobalt concentrates. Copper was concentrated via flotation and, at the optimal conditions its grade in the concentrate was 31.9 wt%. Cobalt was concentrated to 8.6 wt% b ycarbothermically reducing the flotation tailings with coal in a temperature range of 800–1050 °C and followed by magnetic separation. The reaction products were analysed by atomic absorption spectrometer (AAS) and scanning electron microscopy (SEM) techniques. The best carbothermic reduction temperature was found to be 950 °C due to maximum metallisation and less sintering between gangue and metallic/alloy phases.

Mar 1, 2017

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By Jorge Luiz Soares do Couto

O presente trabalho tem como objetivo realizar uma análise comparativa do comportamento de quatro metais de solda obtidos pelo processo arame tubular de forma a avaliar o efeito da relação Ni-Mn nas propriedades mecânicas. Foram soldadas juntas multipasse, com consumíveis da classe 110ksi de resistência mecânica, preaquecimento de 200°C, corrente contínua e posição plana e aporte térmico nominal de 1,2 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal depositado, na condição de como soldado e após tratamento térmico pós-soldagem. Os resultados mostraram que as melhores propriedades mecânicas foram obtidas para uma composição contendo 1,35%Mn e 2,50%Ni. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma redução da tenacidade ao impacto dos metais de solda de maior resistência devido à precipitação de carbetos nos contornos de grão.

Aug 7, 2018

By Mark Jolly, Xiaojun Dai

"Foundry engineers in the traditional foundry usually regard the quality of casting component as the most important issue and leave the energy saving or energy efficiency as the subsidiary one. This frequently causes disproportionate energy consumption as a result of the inefficient casting processes used and increases the production costs. This paper presents the novel CRIMSON aluminium casting process and compares its facility and melting process with traditional melt furnaces and aluminium alloy melting process. A real example is investigated to demonstrate quantitatively how the traditional foundry wastes energy and what the improvement of energy efficiency can be achieved using the new CRIMSON method. The results of this investigation will help the foundry engineer recognize the importance of energy saving and demonstrate how to use this new technology to reduce production costs and carbon footprint without decreasing the quality of the cast component.IntroductionAluminium melting in metal casting industry is an energy intensive process where it is estimated that the energy consumption is in the order of 1,700 ~ 4,700 kWh tonne-1 in using crucible and natural gas [1]. Different countries may use different energy resources for aluminium melting: in US the main energy resources are natural gas, electricity and coke [2] and in UK most of the foundry use electricity, gas and oil as energy resources [3]. Due to the pressure of rising energy price and the strict environment law, it is anticipated that under the right socioeconomic conditions, the efficiency optimisation of industrial process can be an important step toward increased industrial sustainability [4]. In metal casting industry the energy efficiency of a casting facility depends largely on the efficiency of its melting and heat treating performance. In association with the two performances, over 60 % of the total process energy costs are represented in a typical casting facility [5] where there are huge opportunities for metal casting industry to adopt the best energy practices for potential energy saving. How to ameliorate the current processes for increasing energy efficiency will have a vital effect on reducing the production costs and increasing the competitiveness. For instance, by implementing some state of the art technologies such as the CRIMSON method in aluminium alloy casting will make use of such opportunities."

Jan 1, 2011

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines is a promising avenue for overcoming some of the challenges facing mine operators. These include, but are not limited to, the issues related to safety and health of underground workers, better use of the shift time leading to increased productivity, skilled manpower shortages, and remoteness of some mine sites. Autonomous load-haul-dump machines and trucks offer several benefits over man-operated ones, but their use at their full capacity is a challenging and complex task. This paper makes an overview of commercially available equipment and systems and their applications. It examines factors affecting adversely availability, utilization, and production efficiency of autonomous vehicles and compares them to conventional man-operated machines. Technical and operational aspects are discussed and their criticality is analyzed. Based on that, recommendations concerning means and measures that may help raise operational effectiveness are given. It is stressed that due to a scarcity of publicly available information on the performance and cost of autonomous loading and haulage operations, more field studies and in-depth analysis are needed.

Feb 23, 2014

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By Gilbert Soler

PRODUCERS of alloy steels recognize the importance of chemical composition in rela-tion to the hot-working properties and the typical surface defects found in their prod-uct. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization character-istics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures as well as the tendency toward scale formation and decarburization, This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative impor-tance of these factors in relation to the hot-working properties and surface charac-teristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel.

Jan 1, 1940

By William P. Shinn

It is almost exactly seven years since the last previous meeting of the Institute in this city. In a paper on " Pittsburgh, its Resources and Sorroundings," read at that meeting, I showed that Allegheny County had produced in 1878, " one-twelfth of all the pig-iron,.... two-ninths of all the rolled iron (except rails), over one-eighth of all the Bessemer and open-hearth steel, two-thirds of all the crucible blister and puddled steel, one-fourth of all the glass, one-eighth of all the coal, and one-sixth of all the pig-lead produced in the United States;" and the object of this paper is to show that, great as the record then was, it has been greatly surpassed since.* Population. In my former paper I expressed the opinion that the census of 1880 would show the population of Allegheny County to be in excess of 300,000. The census report made it 355,869. The following shows the growth of the county in population from 1790 to 1880: 1790,...........10,309 1800,........... 15,087 1810,...........25,317 1820,...........34,921 1830,...........50,552 1840.............81,235 1850............138,290 1860............178,881 1870,...........262,204 1880,...........355,869 This makes Allegheny County, in 1880, rank sixth in population of the counties of the United States, whereas in 1870 its rank was ninth. The population of Pittsburgh in 1880 was 156,359, being twelfth

Jan 1, 1886

By V. F. Parry

The author wishes to acknowledge the advice and criticism of A. C. Fieldner, chief, Coal Division, Bureau of Mines, United States Department of the Interior; the assistance of Durbin Van Law, consulting industrial engineer, Denver & Rio Grande Western Railroad, Denver, Colo., who furnished valuable information on trends of coal production in Utah by making available his unpublished report "Utah Coal Industry"; and the aid of J.C. Beltz, associate research chemist, Bureau of Mines, Washington, D. C., who reviewed and checked the data, and of W. S. Landers, assistant chemical engineer, Bureau of Mines, Golden, who assisted in the preparation of many of the statistical data, in this report.

Jan 1, 1942

By William L. Porter

From the first day of new miner training until the day they retire, mine workers will experience changes due to the normal aging process. It is an unfortunate fact of life that many age-related changes result in diminished physical, sensory, or cognitive capabilities. Of course, workers also gain a tremendous wealth of experience, knowledge, and insight as they age, making them a vitally important resource for their company. Effective leveraging of this precious resource requires both an appreciation of the changes that occur with age and an understanding of methods that can be used to reduce the injury risk that may result. The purpose of this training is to provide the information necessary to accomplish these objectives. Aging workers may not necessarily have a higher injury risk overall; however, the effects of a musculoskeletal injury (MSI) on older workers may be more extreme. MSHA data show that not only does the percentage of MSIs increase when workers are over age 30, so does the number of days lost per injury, as shown in the graph below [MSHA 2005]. [ ] Protecting the safety and health of aging workers requires matching the demands of the job to worker capabilities. This means reducing or eliminating risk factors for injuries, such as heavy lifting, awkward postures, static postures, repetitive movements, and/or vibration exposures. In other cases, it may mean improving visibility or streamlining processes. Designing jobs to accommodate the changing capabilities of older workers will not only reduce injury risk for older workers, it will have the added benefit of protecting younger employees as well.

Jan 1, 2008

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976