Search Documents

By R. E. Gilchrist, R. F. Nielsen

When a gas is displaced by mother in a porous medium, and there is a relative immobile liquid present. there is a transition zone in which the gas composition varies from essentially that of the original gas to that of the injected gas. The change in extent of this zone with time may be governed by a mixing process in the direction of flow and by the rate of establishment of gas-liquid equilibrium, if the gases are appreciably soluble in the liquid. The relative importance of these two factors in deterri~ining the growth of the transition zone is discussed, with appropriate equations and experimental data. INTRODUCTION The various solution methods of oil recovery involve a transfer of the components of a mixture, whether within a single phase or between a liquid and gas. The similarity of a natural porous medium to systems used in separation and chromatographic processes makes it seem reasonable that certain concepts used by chemical engineers in "mass transfer" might be applicable to petroleum reservoirs. One approach, the HETP (height equivalent to a theoretical plate), involves a distance or length of time over which equilibrium might be con. sidered as established. Another approach involves direct use of a rate of mixing or rate of establishment of equilibrium. The latter approach has been preferred in relation to production problems. DISCUSSION AND PROCEDURE When a gas or liquid in a porous medium is displaced by one of different composition but miscible with it there will be set up a transition zone in which the composition varies from cssentially that of the original fluid to essentially that of the injected fluid. If the fluid being displaced is a gas, and there is a relatively immobile liquid present, the transition zone may be

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount lVIorgan mine. It will be admitted that in all mining operation, the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be ineluded, as it is necessary to understand the eonditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan.

Jan 1, 1910

By Kennedy, Joseph E.

MANY things must be considered in coming to a decision as to what type of crushing and grinding equipment is to be used for preparing run-of-mine ore for concentration, amalgamation, flotation, or cyanidation. This paper is intended in no sense as a thorough discussion of these various factors, but rather contains a few observations based on a wide experience in the manufacture and application of milling machinery. One important governing factor is the tonnage to be dealt with. In large plants treating several thousands of tons in eight hours, a large jaw or gyratory crusher of substantial construction is standard equipment for reducing ore to 8 or 10 in. or finer. In open-pit work, using power shovels with 4- or 5-yd. dippers, a jaw crusher should have a receiving opening of 48 by 60 in., or 60 by 84 in., so that dynamite or hand sledging will not be required for breaking to a finer size before primary crushing. The coarsely broken ore is then conveyed by a belt to vibrating screens, the oversize from which is again conveyed by belts to secondary crushers having openings of 12 or 14 in., the product from which is conveyed to storage. From storage, the material goes to a finishing gyratory for reduction to 1/4 in. or finer.

Jan 1, 1936

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By Tanveer Jahir

With increasing energy costs and mounting government pressure to adopt low emission, green sources of energy, it has become imperative to develop long-term sustainable underground infrastructures that exhibit low power consumption. Underground mining environments are mandated to have ventilation systems in place to replace polluted air with clean air. Continuously running air ventilation systems have proven to be an expensive solution for this requirement. Ventilation-on-demand (VOD) is a cost effective method for not only reducing energy consumption and greenhouse gasses, but also ensuring the safety and well-being of the miners beneath the surface. VOD is achieved by monitoring the air quality in target areas of the mine, and based on variables such as the number of personnel in the area, the number of emission-emitting vehicles, the air leakage around doors and entrances, dust levels, and other key environmental details, the speed and angles of the fan blades are adjusted to increase or decrease the volume of air flow. For over 40 years, Conspec Controls has been developing systems capable of VOD through the use of controllers, gas monitors and personnel/vehicle tracking equipment, providing inexpensive, reliable solutions for underground ventilation.

May 1, 2011

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By R Tom Watts

The blasting industry has changed more in the last five years than in any period to date. The equipment utilized to load boreholes has changed in response to more precise blasting products and programs, and the need to maintain tighter control over product formulations produced by bulk loading equipment. Tread Corporation has built over 1,300 heavy ANFO type bulk loading units currently operating in over 40 countries worldwide. These units have been designed to meet almost every possible loading scenario but there are always new situations that require special designs and configurations to meet the challenge. The focus of this presentation is to make you aware of the process that should be used to determine the equipment best suited for your application. We will discuss loading cycle times, delivery rates, multiple product mixing capability, capacities, manpower utilization, regulatory compliance, and where and when to use automation in the loading process. We will also discuss the suitability of chassis with regard to ground pressure, turning radius, terrain, weather conditions as well as highway suitability. The US Bridge Law as well as laws that cover the concept of axle loading and spacing will be covered. Through new computer aided design and modular design capabilities, you can now have almost any configuration required to meet your bulk loading objectives. We will also review the range of equipment currently available in the market place and discuss tradeoffs between price, capacity, and complexity.

Jan 1, 2000

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By Rudi Toba

Several areas at the DOZ haulage were observed for the crusher’s location. Initially the new crusher designed position was west of the crusher 1, but due to concerns of the mine crack zone (deep MLZ) the crusher position moved to the south. The new crusher location is situated in a diorite rock massive between 3053 – 3079 levels, with the overall excavation of 2500 cum and dimension of 14m long, 14 m wide and 14 m high. Main Crusher chamber itself excavated by development jumbo in three lifts. Development of access to the bottom crusher was developing the same time as chambering the top crusher. The pocket of the crusher mined with vertical crater retreat system which is initiated in one time after middle slot raise. Collaboration between production and perimeter blast holes to be obtaining in control the actual cuts as per the design shape.

Jan 1, 2007

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

The state of the tunneling and underground construction industry and the advancements of the industry?s biggest machines were the main topics at the 2008 edition of the UCA of SME?s annual George A. Fox Conference. This year SME hosted more than 250 tunneling and under-ground construction professionals at the Graduate Center, City University of New York. During the morning session of the long-running one-day conference, attendees heard a state of the industry through the annual Home-town Update where it was evident that the industry is doing well. Michael McHugh of Moretrench cruised through the many projects that are under way along the Eastern seaboard of the United States and said he could have gone longer if time allowed. An example of how well things are going for the industry is a look at New York, where the industry is flourishing. The New York City Water Tunnel # 3 project is a $668 million project that was awarded to Schiavone/Shea/Frontier Kemper joint venture in 2004. McHugh said that mining on the project was completed in August 2006 and that all con-tract work is expected to be completed by August 2009. The Second Ave. Subway is a $337-million twin tunnel project that will connect upper Manhattan with the financial district. This is a four-phase project. McHugh said the Metropolitan Transit Authority obtained full funding in 2007 and construction awards will be awarded during the next two years. The No. 7 Line Flushing extension, a five-year, $1.15- billion project that will redevelop the Hudson Yards area of Midtown West and the New York City Water Tunnel No. 3 project is the largest capital construction project in New York City?s history. McHugh said the project was given notice to proceed on Dec. 13, 2007. The project includes three large shafts, two parallel 6.7 m (22 ft) tunnels at 2,000 liner m (6,500 liner ft), one large cross adit, one large underground rock cavern station with two interlocks and eight penetrations. These were just a few of projects mentioned in the Hometown Projects update.

Jan 1, 2008

By J R. Goff, R Carver, D S. Sheppard

The REGCHEM (Regional Exploration Geochemistry) stream sediment geochemistry database of open file mining company data, managed by GNS Science, was recently made accessible via the internet (http://maps.gns.cri.nz/website/minmap/). REGCHEM provides coverage of selected elements in mineral rich areas of New Zealand. Analysis of REGCHEM data highlights problems with inconsistencies between different surveys in terms of sampling methods, number and types of elements analysed, analytical techniques and detection limits. New, consistent multi-element geochemical surveys with national coverage are required. To test sampling, analytical and data treatment techniques for the new surveys, a pilot stream sediment geochemical survey was carried out in the Thames area, Hauraki Goldfield. Seventy samples were collected in an area of 220 km2 representing about one sample every 3 km2. The samples were analysed for 50 elements, mostly by XRF.   Regional patterns are apparent in the concentrations of some elements. Several elements, such as As, Cd, Cu, K, Pb, Sb, Se, and Zn exhibit anomalous concentrations mainly in the western part of the study area, related to Au-Ag-Zn-Pb-Cu epithermal quartz veins and porphyry Cu occurrences in hydrothermally altered andesitic terrane.   Mercury is anomalous in southern samples, reflecting cinnabar occurrences in the Kauaeranga valley (eg Mangakirikiri), and the occurrence of cinnabar as a late stage mineral in some of the Thames epithermal veins. Ba and U are anomalous in the eastern samples, and these anomalies are probably related to the presence of rhyolitic rocks in the eastern part of the project area.

Jan 1, 2006

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coottha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1996

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974