Search Documents

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death Of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities In and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years. The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3

Jan 1, 1933

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

This report is a proceedings of a briefing recently sponsored by the Bureau of Mines at which Bureau personnel presented findings from their research efforts to improve steelmaking techology currently used in the United States. The papers contained in this report address many areas of concern to the iron and steelmaking industry. Among these are improving arc stability in electric arc furnaces, preheating ferrous scrap to reduce energy consumption, fluorspar substitutes in steel-making, basic steelmaking refractories, corrosion of iron-based materials, improvements in stainless steel acid pickling processes, recycling of stainless steel dusts and other wastes, and use of wastes as a source of zinc for electro/galvanizing.

Jan 1, 1988

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By Ernest J. Conway

This report presents engineering drawings for six material handling devices for underground coal mines. The devices were designed under a U.S. Bureau of Mines program to reduce injuries from material handling during mine and equipment maintenance. The six devices are (1) scoop-mounted 1411: boom, (2) swing-arm boom, (3) heavy-component lift-transport, (4) mine mud cart, (5) container-workstation vehicle, and (6) timber car. Each device is described briefly, and recommendations are made concerning the design of new devices.

Jan 1, 1989

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By William Seymour, L. D. Schmidt, J. W. Myers, W. T. Reid

"This investigation was conducted by the Bureau of Mines as part of a program of the Solid Fuels Administration to encourage the utilization of anthracite fines, the objective being to determine the practicability of using anthracite fines in the manufacture of packagedThe experimental loss of packaged fuel covered by this report were made at a commercial plant using the Glenn Smith process and ordinarily making packaged fuel from Pocahontas screenings. These lots included several made from straight antimacite mines and others made from various blends of anthracite fines with four different bituminous coals. In all cases an asphalt binder was used. Determinations of the physical properties and the cobustion characteristics o the various samples of packaged fuel were made by the. Bureau of Mines at the Central Experiment Station.The physical tests indicated that a packaged fuel of sufficient strength for ordinary handling can be made from straight anthracite coal or from a wide variety of blends of anthracite fixes with bitunimous coal, using asphaltic binder. However the combustion tests indicated that packaged fuel made from anthracite alone tended to crumble excessively during burning and that as much as 30 to 50 percent of a caking coal may be required In the mixture to produce a block having satisfactory combustion characteristics.The authors wish to acknowledge the. splendid cooperation of Messrs. H. W. Kelly, J. L. Mooney and C. H. Stoss of Columbus, Ohio, who were chiefly responsible for obtaining the materials and making all the arrangements necessary for the production of the packaged fuel for testing.Thanks are due to the officials of Carnegie Institute of Technology for the use of their Olsen. Testing Machine and to H. M. Cooper and W. A. Selvig of the Bureau of Mines for analyses and tests."

May 1, 1946

By Cathy Aimone-Martin, Brent Meins

A comprehensive instrumentation program was implemented at the Howland Hook Marine Terminal on Staten Island, NY during proximate underwater rock blasting in 2014. Forty-two blasts took place over a 4-week period to deepen the 1200-ft (366 m) Berth 3 from -45 ft (-14 m) to -50 ft (-15 m) MLW to accommodate Post-Panamax vessels. Approximately 86,000 yd3 (65,752 m3) were blasted 120 to 9 ft (37 to 2.7 m) from the wharf to a total depth of -57 ft (-17.4 m). Pre-blast planning included developing and implementing a comprehensive monitoring plan and setting vibration and strain limits to protect the wharf. The plan outlined methods to measure vibrations on five corners of four concrete deck sections, on five concrete-filled pipe piles just below the pile cap near deck corners, and in bedrock adjacent to pile sockets. Water overpressures were measured near instrumented piles for 19 blasts closest to the wharf. A total of 19 geophones were secured to the wharf structure and buried 12 ft (3.7 m) in drilled holes.

Jan 1, 2016

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ&apos; in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of &quot;pure&quot; leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

By R B. Evans, M G. Townsend

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre-Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth. The raw material is crushed and fractionated to produce a product of less than two micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972