Search Documents

By J. H. East, E. R. Maize

INTRODUCTION PROBABLY no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines, testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. So far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. ADJUSTMENTS OF DIESEL ENGINES FOR UNDERGROUND USE A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn 1 lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:I, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Diesel operates in confined places should contain less than 1/2 pct of carbon dioxide and at least 20 pct of

Jan 1, 1947

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By Arthur F. Taggart

TO all Mineral Dressers, but particularly to those in the Coal and Industrial Minerals Divisions: Ted Counselman, retiring after two years at the helm of the Milling Committee, pointed with pride to the continued growth of that committee, and sang the swan song "Why ain't we a Division of Mineral Dressing?" Our genial Secretary pointed out, handily, that, you see, the way the Institute is divided there are several blocks running across this way here, and one running all the way down here, and another running part way down here, and they all cut across each other like this, and anyway the miners want to be a Division now, so why not you Mineral Dressers be good and not upset the big Institute organizational chart? And anyway again, Divisions have vested interests, and a Division of Mineral Dressing would take something away from Coal and something from Industrial Minerals, and any good institutional man can see that a Division would never give anything up. It was all quite confusing, and apparently not too convincing, because then the Milling Committee went ahead and voted unanimously it is a good idea, let's see what the other fellows think about it as well.

Jan 1, 1944

By G. R. Peterson

To determine the availability of aluminum from world bauxite resources, the Bureau of Mines investigated 139 bauxite deposits worldwide and evaluated the potential production of aluminum based on the demonstrated resources of bauxite ore from 91 mines and deposits in 22 market economy countries. The demonstrated resources of the bauxite mines and deposits included in this study represent an in situ resource of 20.2 billion metric tons of bauxite. Total identified bauxite resources in market economy countries amount to roughly 31.9 billion tons. Of the demonstrated resource, some 18.8 billion tons of bauxite considered minable provide a production potential of 3.6 billion tons of primary aluminum. Given the wide geographic distribution of bauxite deposits, stable supplies of bauxite for aluminum production seem assured well into the next century. However, a tight market situation could develop during the 1990's unless the real price of aluminum increases enough to stimulate massive new investments in production capacity, particularly in refining and smelting. This study indicates that a real price of at least $0.85 per pound (in January 1980 dollars) would be necessary to stimulate the required investments and provide a sufficient rate of return on invested capital.

Jan 1, 1983

By Francis Foley

INTRODUCTION DURING the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr: Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.1 Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 2, 1926

By S. G. Ercelebi

In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli Open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system. Keywords: Open pit mine, equipment selection, dispatching, linear programming, closed queuing network theory

Jan 1, 2009

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By H. F. MILLE, Charles A. Kumke

This paper describes mining operations at the Iron King mine of the Shattuck -Denn Mining Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices and methods in various mining districts of the United States . The mine and surface plant of the Iron King mine are situated in secs . 15 and 21 , T. 13 N. , R. 1 E. , about 20 miles by State highway 69 east by southeast from the city of Prescott and 1 mile southwest of the mining town of Humboldt on the Prescott -Mayer branch of the Atchison , Topeka & Santa Fe Railroad (fig . 1 ) . A l-mile truck haul brings the mill concentrates (lead and zinc ) to bins on a siding of this line at Humboldt ; the silver -gold bullion is handled separately . Some of the oldest residents in the vicinity of Prescott claim that the original location for the Iron King mine was made in 1880. The earliest recorded production was in 1906-1907 . During the first World War the mine produced fluxing ore for the Humboldt smelter . In 1936 the property was purchased under tax sale , and a mill (140-ton capacity ) was erected in 1938. The capacity of this mill was increased to 225 tons the following year , and a cyanide plant was added in 1940 to treat mill tailings . In 1942 the Shattuck -Denn Mining Corp. purchased the property . A new working shaft was sunk , mine development was speeded , and mill capacity was again increased . The predominating locally formation of this district is a pre -Cambrian schist known as Yavapai schist . The Iron King deposit , which carries gold, silver , lead , zinc , and copper , occurs as a series of lenses in a sheared zone of the pre -Cambrian schist . Down to the 600 -foot level the ore was mined and drawn by the shrinkage method . The cut -and -fill method was adopted for the lower levels . Waste rock for stope fill was provided by block-caving an area on the 600 level . Main haulage drifts were driven in the firm footwall , and crosscuts were driven across the mineralized zone at 100 -foot intervals . Grab samples taken from each car of every working place and channel samples cut every 5 feet in development work are considered sufficient for estimating ore reserves .

Jan 1, 1950

By A. Fahimifar, H. Soroush

Abstract: In order to develop non-destructive methods in studying physical and mechanical properties of rock and replacing them with difficult and expensive static methods, several ultrasonic tests were carried out on cylindrical rock specimens in accordance with the ISRM suggested methods and velocity of P and S waves were determined. Also, density, porosity, water absorption, uniaxial compressive strength and indirect tensile strength were determined for each specimen in accordance with ISRM suggested methods. According to above tests static and dynamic elastic constants were calculated After statistical analysis of data obtained from tests, the relationships between velocity of elastic waves and physical or mechanical parameters were determined and some equations were obtained. Also similar analyses were performed on static and dynamic constants and some equations were extracted. Using these equations, the physical and mechanical parameters of rock and also static elastic constants can be estimated by conducting simple and quick tests (i.e. ultrasonic tests). Abriß: Um zu entwickeln, die zerstörungsfreien Methoden für Studieren die physischen und mechanischen Eigentümer von Steinen und auch ist für Ersetzen diese Methoden mit schwierigen teuren statischen Methoden, mehrere altrasonic Prüfungen auf zylindrischen Steinproben gemäß ISRM anregenden Methoden und den Geschwindigkeiten von S und P Wellen bestimmt worden sind durchgeführt worden. Außer der Dichtheit und der Porosität betonen Wasser Aufnahme und monoaxial Widerstand und dehnbaren indirekten Widerstand jeder Probe betreffend der erhaltenen Ergebnisse die atmosphärische Aufladung sind bestimmt worden und die dynamischen Faktoren der Steine sind kalkuliert worden. Nachdem statistische Analyse die Korrelation der Ergebnisse zwischen der Geschwindigkeit elastischer Wellen und mechanischer und physischer Eigentümer der Steine erhalten worden ist, und mehrere Verhältnisse sind vorgeschlagen worden. Eine ähnliche Analyse ist auf atmosphärischer Aufladung und dynamischen Faktoren durchgeführt worden und einige Verhältnisse sind erhalten worden. Mit Hilfe dieser Verhältnisse die physischen und mathematischen Eigentümer von Steinen und auch können die Statistik Faktoren durch einfachen und schnellen altrasonic Prüfungen erhalten werden. Resume: Puor le development des method non-destructive et evaluuation des propietes physical et mechanical des rock et superseding avec les methods dificzle et cher statique, c‘ est fait plusieur essayes ultrasonique sur les echantillons cylinrique et par a port le proposale TSRM et le vittesse des ondes P et S et densite et porosite et absorption des eaux le resistant de pression uniaxial et resistance de chaque echantillon est determinee. A la fin en base des resultat obtenue les constant statique et dynamique des roches sont calcule. Apres les analyses statistiquc sur les resultat obtenue du les essaybs, c‘ etait produit les relation entre les viptesse les ondes elastique et les proprietes physic et mechanicue des roches et c est propose quelque relations. Aussi le meme enterpretation sur les constant statique etdinamique. En possezon de ces relations, les spesificatio physique, aussi on peut trouver leur constant statique, avel les essayes sample et raptid a d ultrasonique.

Jan 1, 2003

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By E. D. Attanasi, J. H. DeYoung

Mineral exploration activity in the US suffered through another depressed year in 1984. And continued strength in precious metals (and possibly industrial minerals) exploration failed to make up for declines in other minerals. 1984 offered little solace for the explorationist. But some new data on mineral exploration provided better statistics for analysts of US mineral exploration trends. The Society of Economic Geologists (SEG) published data from its survey of 1980,1981, and 1982 exploration by US and Canadian companies - 96 companies responded (Barber and Muessig, 1984). In addition, a Mining Engineering (April 1984 p. 345) article by Emerson and Ivosevic presented their data on annual exploration expenditures in the US for gold and for all minerals from 1961 through 1983. A review of 1984 domestic exploration and development activities reported in several industry journals indicates that almost 90% of those projects were directed at gold and silver deposits. Statistics on 1984 exploration expenditures are not available. But some industry observers believe that precious metals accounted for an even larger share of industry's exploration budget in 1984 than in 1983. According to the data of Emerson and Ivosevic (ME, April 1984, p. 349), gold exploration expendi-

Jan 5, 1985

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By M. Hopf

The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However, even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able consistently to identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed).Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa. Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway

Jan 1, 2006

By Paul Swatkowski

A Note About Copyrighted Material ??Permission to Use? has been granted ?Teachthe7habits ?Think win/win (4thHabit) ?Don?t stop here ?i.e., buy the book

Jan 1, 2009

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981