Search Documents

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By Oy Leuangthong

The McMurray formation in the Athabasca oil sands deposits of Northern Alberta is part of the world?s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modeling of the McMurray formation using modern geostatistical techniques. Geostatistical modeling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: (1) assessing the most appropriate stratigraphic transformation for optimisation of the correlation structure, (2) determining representative distributions with declustering and debiasing techniques, (3) modeling spatial continuity of the bitumen grade, fines grade, water saturation and other petrophysical variables, (4) performing estimation and cross validation as checks against simulation results, (5) performing simulation for uncertainty quantification of bitumen and fines grade, and (6) model checking of simulation results against the input data and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed.

May 1, 2004

By Marina Carreiro-Silva, Cátia Cardoso, Bruce Shillito, Lisa Mevenkamp, Alastair Brown, Maria J. Bebianno, Juliette Ravaux, Inês Martins, Nélia C. Mestre, S. Sousa Vânia

Mineral extraction activities in the deep sea will expose the local fauna to potentially toxic compounds. However, very few data are currently available on the complex ecotoxicological risks to deep-sea fauna from the potential release of heavy metals, trace metals and Rare Earth Elements (REEs). Nonetheless, this is key information essential to support the regulation of industrial activities in the deep sea. One of the fundamental issues that the MIDAS project will address consists in exploring the concept of whether the existing toxicity test protocols and limits established in shallow-water species are applicable to deep-sea mining. We will detail the specific challenges to recommending exposure limits within the deep sea and show preliminary results of comparative toxicity tests in the shallow-water and in the deep-sea environment.

Sep 1, 2014

By L. Alan Weakly

The Powder River Basin is the largest strippable reserve of compliant coal in the United States. It is the mother lode, for this Basin is currently supplying 25 percent of the coal produced in the US annually. This paper updates what has happened in the Basin since 1993 in terms of increased production, higher productivity, changes in mine ownership, safety statistics, new equipment, latest coal technologies, and electrical deregulation ramifications.

Jan 1, 1998

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By David J. Kusler

The Bureau of Mines reviewed current technology in the refractories consuming industries and evaluated the impact of changes in technology on the supply and demand of refractories. Literature was searched and contacts were made with leading consumers and producers of refractories. The distribution of refractories by value of shipments to users was surveyed. The report shows that the percentage distribution of refractories sales to the consuming industries has remained essentially constant during the last decade but that substantial changes have occurred in the relative distribution of types of refractories. The trend in pyroprocessing technology in recent years has been toward higher temperatures, which require more costly refractories. This fact is reflected in the impressive gain in the dollar value of refractories sales, which in 1968 was about one-third greater than in 1960, and the rapid growth of refractories based on high-alumina, magnesia, zirconia, carbon, and other materials, at the expense of fire clay, silica, and chrome- based refractories. An appendix to the report contains refractories value and shipment data tabulated in a manner by which trends in the distribution of refractory types can be observed from 1955 to 1968. In addition, unit values are presented on a per-ton basis for comparison.

Jan 1, 1970

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Jean G. Fortin

The manufacturers' proposed technology has been a key factor in selecting production, mobile and fixed equipment in order to achieve the targets set in our 2026 mining plan. This paper will present an overview of the most recent technologies adopted by Québec Cartier Mining Company for communications, power supply, dewatering, drilling, loading, hauling and processing. All these new technologies contribute to the improvement of our day to day operations while operating with a state of the art asset reliability program.

May 1, 2007

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

By Robson W. D, Irwin D. A

In November, 1932, an investigation of silicosis was undertaken at the, McIntyre Porcupine Mine, Schumacher, Ont., atfer a discussion of the problem with Sir Frederick Banting and his, staff. As a result it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions.At that time 50, guinea pigs were placed in the crusher nouse tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent., of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill.The C02 combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid and alkaline solutions on the solubility of silicious materials. Gye and Purdy were the first to point out that the chemical reaction and not the physical presence of silicious material was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response while the 10-12 micron particles produced only a foreign body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter. We assumed that if the solubility of the silicious material retained in the lung could be reduced sufficiently by the addition of some non-toxic element or compound the usual fibrotic respohse would be modified. We found that the addition of certain compounds to silica would reduce its solubility in the beaker to a slight extent. But these compounds, when mixed with quartz...

Jan 1, 1945

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991