Search Documents

By AIME AIME

HOWARD H. PRESTON, professor of economics and business at the University of Washington, presented a paper before the North Pacific Section, A.I.M.E., on Jan. 23, on the "Economic Aspects of Gold and Silver." He carefully reviewed recent governmental actions that have affected those metals and gave an interpretation of their effects. A brief excerpt from his address; follows: Including the proclamation of March 6, 1933, the principal steps of the present Administration which have carried the United States off the gold standard and led up to the present program have been: (1) The Presidential proclamation of March 6 controlling gold. (2) The monetary sections of the Emergency Banking Act of March 9. (3) Mobilization of gold under Executive orders issued March 10 and April 5. (4) The gold embargo by Executive order, April 20. (5) The controlled inflation bill, May 12. (6) The joint resolution abrogating the gold clauses, June 5. (7) The Executive orders on newly mined gold, Aug. 28. (8) The President's radio address of Oct. 22 and the R.F.C. gold-buying program. (9) New anti-hoarding order calling in small holdings of gold, Dec. 28, 1933 and Jan. 15, 1934. (10) Nationalization and revaluation of gold' (Message to Congress, Jan. 15).

Jan 1, 1934

By H. Foster Bain

I. INTRODUCTION. By H. FOSTER BAIN.+ THE recently aroused public interest in the conservation of our natural resources has peculiar importance to mining-men, since they deal with resources which are stored products. Within certain limits, the fertility of a worn-out soil may be restored, deforested areas can be replanted, one year's wasted water-supply is followed by another; but coal and ores, once taken out, cannot be mined again, and should therefore be conserved with especial care. This means, however, not that mining should be restricted, but that it should be done most economically and with the minimum of waste.

Nov 1, 1908

By J. W. Thompson

"The Republic of Colombia on December 30, 1919, enacted a new petroleum law. The Act is expressly limited to mineral oil, natural gas, bitumen, wax and fossilized resin and to asphalt intended for export.The law is not only intended to encourage local investors, but to attract foreign capitalists for oil development. Provision is made for a special edition ion of the law in such languages as the Government may deem necessary to give it extensive circulation within the country and abroad. The published editions must contain the provisions of the law relating to alienship and naturalization.All public lands, or what are termed unclaimed lands, are open to flee prospecting for the purpose of discovering the deposits named in the law, A prospector must obtain from the Government a, license which binds him to deliver to the Government topographic plans of the lands prospected, together with reports of their prospective yielding capacity. This license does not vest the li¬censee with any preferential right for contracting or leasing and may be drawn by the Government at any time.If a discovery is made by a licensee of any of the deposits named and he desires to exploit the same, he must present a memorial or application to the Ministry of Public Works, stating:- (a) the location and municipal district in which deposit beds are found; (b) boundaries of the zone of exploitation, which shall not be more than 5,000 or less than 1,000 hectares; (c) the names and nationality of all persons for whom the lease is sought and the action and time within which,they propose to make the exploitation; (d) the name of the corporation and its legal representatives with their residences; (e) if an alien, he must state his willingness to comply with the law relative to alienship and naturalization; (f) agreement to abide by all of the provieions of the law with regard to Government supervision, payment of taxes, rate of lease and causes of forfeiture; (g) the rate of rent or royalty that the applicant offers to pay, together with any other circumstances that may make the proposed lease advantageous to the Nation."

Apr 1, 1920

By P. Sarnoff

Gold has always been a crisis investment. For centuries gold has been considered globally the money of last resort. In time of war, inflation, financial uncertainty, political upheaval there has with few exceptions always been a flight to gold. The gold paradox simply is that even though we have gone through for the past handful of years all the kinds of. anxieties that would cause the gold price to rise, it has instead dropped drastically. Figure 1. illustrates the important factors that influenced the gold price significantly up or down before 1987. Obviously, since then, even though we have had wars, inflation, financial problems involving breaking banks and thrifts let alone collapsing financial institutions, the gold price has both in the long-term and the short-term trended downwards. Figure 2. depicts the gold price path since 1987. If the presence of time-honored and time-tested factors that should have driven the gold price up didn't do the job, then logic dictates that new factors to drive the gold price down and keep it depressed arose. And they did. But before addressing these depressants permit me to turn to the arcane art of gold price prediction and fore-casting.

Jan 1, 1992

By K. C. Dean

Discarded automobiles represent the greatest single resource of reusable metals, plastics, and rubber in the United States. This report presents results of Bureau of Mines research, conducted from 1965 to 1983, on separating and recovering useful materials from the scrapped hulks, using old and new metallurgical techniques combined with standard scrapyard methods. The Bureau determined the materials composition of three composite cars designated as circa 1960, mid-1970's, and early 1980's, and used these cars to study smokeless incineration and hand-sorting techniques. In studies on treating rejects from automobile shredders, the Bureau designed a process that included air classification, water elutriation, magnetic separation, handpicking, and heavy-medium separation, and also investigated cryogenics and liquation. Complete recovery of cop-per and other metals was economically made by hand and tool dismantling, leaching, or selective melting of starters and generators. Techniques are also discussed for plastic recovery and waste tire treatment.

Jan 1, 1985

By W. L. EGY, GEORGES. RICE, L. M. JONES, J. K. CLEMENT

This report has been prepared, not only for the purpose of recording the results of the first series of coal-dust tests conducted in the experimental mine of the Bureau of Mines, but also to place before the mining public a description of the mine and an account of the objects sought in its establishment. Soon after the organization of the technologic branch of the United States Geological Survey, J. A. Holmes, then chief of the branch, concluded that for the solution of various problems relating to the causes and prevention of mine explosions it would be best to carry on large-scale tests in a mine rather than in a surface gallery. The idea of utilizing the underground passage of a mine for making explosion experiments did not at' first meet with general approval among investigators in this country or abroad. Many thought a mine passage was not a proper place in which scientific tests could be conducted, as great difficulty in controlling conditions was expected. However, after all arguments for and against such an investigation had been carefully considered, plans for opening an experimental mine were definitely adopted by the Bureau of Mines in 1910, and an allotment of funds was made to carry out the project. The first endeavor was to find an existing mine suitable for the purpose, but the mines offered by owners were either worked out, were wet, had poor roofs, or presented complications of various kinds, so that it was finally decided to open a mine if a site could be obtained having natural conditions that would fill the various requirements. A most desirable location was found on property of the Pittsburgh Coal Co., near Bruceton, Pa. The president of this company, Mr. W. K. Field, the general manager, Mr. G. W. Schluederberg, and the chief engineer, Mr. E. J. Taylor, rendered every possible service in

Jan 1, 1913

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By Sandra K. Zacharias

Brass, a deliberate alloy of copper and zinc, has been known since before Roman times. There are two main methods of making brass: (1) Cementation or calamine process - crushed zinc ore (calamine, ZnC03 , or calcined calamine, ZnO), is mixed with charcoal and small pieces of metallic copper and heated to about 900°C in a closed crucible, (2) Alloying - metallic copper and zinc are melted together in a reverberatory furnace. According to most modern authorities (e.g. Smith and Forbes 1955), the calamine process was the only one used in western Europe prior to the 18th century. At that time, the alloying technique began to take over, because metallic zinc was successfully produced on a large scale for the first time. Previously, this had been a problem because zinc vapourizes at 906°C or about the same temperature at which it can be reduced from its ore. Thus, some means had to be devised to collect and condense the zinc vapour (Tylecote 1976). Metallic zinc was known, however, earlier than the 18th century A.O. Several early finds have been made, including a rolled sheet of metallic zinc found in excavations at the Athens Agora dating to the 3rd to 2nd century B. C. (Farnsworth et al. 1949). The Chinese were producing zinc by at least the 10th century A. D. and, by the 17th century, Chinese zinc ingots were being imported into Europe by the Dutch East India Company (Needham 1974). Metallic zinc is also mentioned in several European documentary sources from the 16th century (e.g. Paracelsus, Agricola). This study traces the changes in Western brass making methods from Classical to Renaissance times by examining documentary and archaeological evidence.

Jan 1, 1999

By O. C. Blade

The term "Ichtnyol" is a name applied loosely to certain preparations used in pharmacy. These preparations do not occur as such in nature but are manufactured by various chemical processes. Ichthyol is the name trademarked for a product manyfactured by the Irhthyel-Gescllschaft (Cordes Hermanni & Co.) of Hamburg, Germany, and marketed in thin, country by Merck & Co., Inc., (5, 86, 87)3/. Although used in the literature rather loosely, the correctly applied word refers to the product obtained by sulphonating and then neutralizing with ammonia a distillate from the oil retorted from a certain high-sulphur bituminous shale found near the village of Seefeld in the Austrian Tyrol. Due to the fact that fossils of fish and marine animals occur in the limestone associated with the bituminous shale, these deposits have long been known as, the "lchthyolite schistc of Seefeld" ( 55) . The Greek word "ichthys"" for fish and the Latin word "oleum" for oil are the words from which the term is derived. The crude, tarry shale oil, whose distillate is the raw material for the sulphonation process, has been referred to since the Middle Ages as "Dürsten" or "Tirschen" oil, and the term "ichthyel oil" has been used occasionally in the literature to designate the retorted crude oil (92, 93, 106, 117). The first application of the name "Ichthyol" to a particular product is credited to Schröter (35, 129). Various names for products manufactured by sulphonating bituminous distillates have been coined, and in some of these names the root from the word ichthys has been retained. Some of these names can be found in New and Nonofficial Remedies under the heading, Sulphoichthyolate Preparation, and Substitutes (5).

Jan 1, 1938

This study relates to continuous face haulage systems in underground coal mines, and was performed by Joy Manufacturing Company for the U. S. Bureau of Mines under the Bureau of Mines Contract No. HO 242025. The effective starting date for this work was June 14, 1974. There were two main reasons for making this study, the first being to find a safer system to move coal away from the face than the currently predominant shuttle car system, and the second being to seek ways to advance the state-of-the-art of continuous face haulage as a means of increasing coal production.

Jan 1, 1975

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By James T. McCartney, Joseph D. Davis

For more than 10 years coke-oven technologists have been investigating the expanding properties of coal on a scale larger than that afforded by laboratory test tubes. Koppers 4/ was among the first to realize that coals can not be differentiated satisfactorily with respect to expansion in coke ovens by the simpler test-tube methods; in his first method 80 grains of fine coal were coked in a cylinder heated from the bottom, so that the zone of fusion (plastic layer) advanced from the bottom to the top. The scale of test was too small; it has been modified by other investigators, but without significant improvement in practical application of the results. Somewhat later Koppers and Jendne 5/ experimented with a small-scale coke even, one wall of which was movable, in which the layer-coking in a coke oven could be simulated closely. This oven was heated from both sides. Their results with this oven showed a peak in the time-pressure curves near the end of the coking, period when the two plastic layers, advancing from opposite walls, meet. They also found that although the smaller oven was heated from one side only and did not show the Pressure peak characteristic of two-sided heating, it still gave results entirely too high. Russell built an oven similar to the movable-wall oven of Koppers and Jenkner and compared results obtained in it on Beckley expanding coal with these obtained on the some coal in the Altieri 7/ small-scale apparatus. Both tests were conducted at the same constant pressure, but heating was from two sides in Russell's oven and from one side in the Altieri tester. Russell found that the two types of test gave comparable results under constant pressure conditions even though the heating procedures were quite different. He showed later, however, that a "borderline" coal 8/ that contracted in the Altieri tester at constant pressure developed a peak pressure of 4 pounds per square inch in the movable-wall oven heated from both sides at constant volume. He concluded from this that testing at constant volume gave results more accurately indicative of dangerous expansion tendencies than those at constant pressure. He also found that heating from both sides in this oven gave higher pressure than heating from one side only.

May 1, 1942

By John D. Rockaway

Failure of the mine floor supporting coal pillars frequently occurs when the subcoal strata include "underclays" or other low strength strata. The failure process has been studied to define the response of these materials to applied coal pillar loads and to determine the applicability of bearing capacity analysis to evaluate unsafe conditions. The study has been accomplished through an investigation of both the intact and insitu geotechnical properties of the subcoal strata and through the installation of floor movement monitoring instrumentation. The results of these studies have indicated that both the shear strength of the underclay and the stratigraphy of the subcoal strata must be considered in the analysis. The shear strength was the major controlling factor determining the ultimate load carrying ability of the materials, but the thickness and stratigraphic position of the weak layers influenced the mechanism of the failure process. The methods of bearing capacity analysis were used to define pillar stability that included provisions for taking into consideration a two-layer system. Conditions assumed for a coal mine where a weak underclay overlies firmer strata. The results of the analysis compared very well with observed mine conditions, indicating marginal conditions in areas of the mine which later experienced pillar support failure. In addition, a "heave factor" was derived to predict potentially unstable floor conditions in the mines studied in detail.

Jan 1, 1979

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By Herbert H. Einstein

This report contains the documentation for 11 computer programs representing the entire computer documentation for the eight-volume report entitled "Risk Analysis for Rock Slopes in Open Pit Mines." A detailed summary of the programs is included.

Jan 1, 1979

By E. E. White

(Cleveland Meeting, October, 1912.) IN, August, 1911, I read a paper before the Lake Superior Mining Institute' on surveying and sampling diamond-drill holes. The present paper gives a more thorough description of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drill-holes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-bole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a 1 Proceedings of the Lake Superior Mining Institute, vol. xvi., pp. 100 to 120 (1911). 2 Recent Practice in Diamond-Drilling and Borehole Surveying, Bulletin No. 91, Institution of Mining and Metallurgy (Apr.. 11, 1912).

Nov 1, 1912

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

The world’s first copper electrorefinery started production in 1869 at Burry Port in South Wales. Built within the Pembrey Copper Works which had commenced smelting operations in 1849, the new refinery was based on principles described in the British patents issued to J.B. Elkington in 1865 and 1869. Refining principles and practices pioneered there were key to the foundation of modern electro-refining practice in what is now a dominant international industry producing over 16 Mt of electrical grade copper annually. This paper explores the background to this pioneering application of the new, early 19th century, science of “electro-metallurgy” and examines its links to the contemporary decorative electro-plating industry and to the shortcomings of 19th century fire refining. The beginnings and early years of the Pembrey electrorefinery are briefly discussed in relation to the quality, applications and pyrometallurgy of copper at the time. More than a decade would elapse before the birth of the electrical age: the Pembrey refinery may be seen as one of its vital precursors. Note: This paper was originally published as part of the Copper 2013 proceedings (A.E. Wraith, P.J. Mackey and J. (formerly R.) Protheroe Jones, “Origins of Electrorefining: Birth of the Technology and the World’s First Commercial Electro-Refinery”, paper in Electrorefining, Vol. V, Book 2, (Eds. R. Abel and C. Delgado), Cu 2013 International Conference, pp. 19-33, IIMCh, Santiago, Chile, 2013). It is reproduced here together with a new Appendix and supporting references that lists the year of commencement of the first electrolytic copper refinery by country, 1869 to 1956. It all, the year of the first electrolytic copper refinery established for 15 countries is included. These 15 countries now produce more that 70% of world refined copper (for 2018). INTRODUCTION In the 1840s, the new science of ‘electro-metallurgy’, a term coined by Smee in 1841 (Smee, 1841), was being adapted to the decorative electro-deposition of silver in a thin, bright adherent coating that was evidently equal in appearance to traditional silverware (Williams, 1976). Chief among innovative manufacturers of decorative objects who took up the new art of silver electro-plating was the acclaimed firm of G.R. Elkington and Co. of Birmingham, England. The company, which vigorously developed all aspects of electro-metallurgy for the decorative trade, entered the field of ‘electrotyping’, a technique in which the surface features of a mould are copied on an electro-deposited copper layer which, when stripped off, can be used to reproduce an imprint of the mould. In essence, it is a form of casting by electrodeposition, invented in 1837 independently by Jacobi in Russia (Pavlova, 1968) and Spencer in England (Wyatt, 1851).

Jan 1, 2019

Statistics is essentially a study of variability, the use of some suitable mathematical model representative of such variability, and the application of this inferred pattern of behaviour to practical problems. Probability theory is the mathematical structure devised for providing models for chance happenings. Perhaps the simplest example of a chance happening is the result obtained in tossing a coin. Although the result of a single toss can never be predicted with certainty, there is no reason why in repeated tosses the expectancy of heads and tails should not be equal. In such a case the outcomes of the experiment are said to be equally likely, so that the probability of obtaining heads (or tails) is 1 in 2, that is, 0,5. This simple probability .model refers to a 'mathematical' or 'unbiased' coin. Whether such probabilities are meaningful for actual coins tossed in any particular way is a matter for experience to determine. Probability models have also provided the basis for representing observed variability in cases where the actual under- lying probabilities are only partly known or defy analysis. A typical example of the latter case is the variability observed in the values obtained from gold or other ore samples. The interacting natural forces which gave rise to this variability are obviously very complex and are unlikely ever to be unravelled completely. In spite of this, probability theory and the more recent geostatistical theories have provided us with models which can represent this variability on a reasonable basis. Applied statistics and geostatistics must therefore never be accepted as exact mathematical sciences. Furthermore, a basic and essential concept is that in the type of applications covered in these notes, no model must ever be accepted as necessarily the final and exact answer to the problem; thus, any model must prove and continue to prove its appropriateness in practice, preferably by follow-up comparisons.

Jan 1, 1981