Search Documents

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By Walisson Silva Gomes

A injeção de carvão pulverizado pelas ventaneiras dos altos-fornos é um dos meios de redução de custos de produção do ferro gusa. Esta injeção deve ser de forma efetiva para evitar possíveis desperdícios de combustível. Esse trabalho teve como objetivo desenvolver uma metodologia de quantificação do teor de carbono na lama e no pó de coletor, gerados na limpeza de gás do alto-forno para auxiliar a avaliação da eficiência de queima do carvão injetado pelas ventaneiras e sua correlação com as variáveis de processo. Nenhuma norma especifica a quantificação de carbono na lama e no pó de coletor. Foram utilizadas duas técnicas de quantificação de carbono em carvão e coque utilizados na Companhia Siderúrgica Nacional, a Análise Imediata, baseadas na norma ASTM D 5142-09, e a Análise Elementar. Um estudo mais detalhado para investigar as possíveis interferências nesses métodos de análise, devido a diferença de resultados entre eles, foi utilizado Difração de Raio-X, associado ao método de Rietveld, e Analise Termogravimétrica de Calorimetria Exploratória Diferencial (TG-DSC). A partir dessas análises foi possível definir o melhor método para quantificação de carbono no pó de coletor e lama de alto-forno.

Aug 17, 2017

By Marcus Vinicius Dias Garcia

O presente trabalho tem por objetivo contribuir para a preservação refratária de baterias de coque, apresentando uma metodologia de planejamento e controle. A condição dos refratários de baterias de coque é crucial para sua produtividade e para o cumprimento de diretrizes ambientais. São desafios (i) a identificação precoce de danos e previsão de seu efeito no desgaste global da bateria, para hierarquia de reparos; (ii) a seleção da técnica apropriada a cada reparo. No presente trabalho, os autores compilam o estudo da progressão de danos sob diferentes tipos de reparo ao longo de mais de 30 anos em baterias heat-recovery e convencionais, de diversos modelos construtivos, e o combinam a tecnologias de inspeção para consolidar uma metodologia de gestão da preservação refratária. A metodologia foi aplicada em baterias localizadas no Brasil, avaliando a condição de mais de 400 fornos em 90 dias. Para a bateria mais crítica, foi identificado um potencial de prorrogação de vida útil em torno de 10 anos.

Aug 17, 2017

By C. C. Hawes

SILICA is the main impurity in iron ore. It is intimately associated with the iron oxide, sometimes free but more often in the combined state, as a mineral silicate. Its separation and purification sometimes present difficult problems to the analyst. In the absence of any definite knowledge to the contrary, orthosilicic acid. H4SiO4, is supposed to be the only silicic acid made, all other forms, such as metasilicic acid, H2SiO3, representing different degrees of its dehydration. These acids are exceedingly weak but form the most stable compounds found in nature. They are known as the silicate minerals and are formed by the combination of the different metallic oxides

Jan 1, 1936

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

D. HARRINGTON: Owing to lack of funds, the United States Bureau of Mines have made no experiments in the Bruceton mines in the use of mudite. MR. McAULIFFE: I doubt that mudite cam be delivered at fifty cents a ton and that a mile of heading can be treated with mudite for ten dollars. You could not dig a ton of sand out of a sand hank for that money. L. C. CLARE: The tram road leading to Wattis mine crosses a shale bed and it is easy to screen the shale through a %-inch sieve and load it into a mine car. W. J. REID: A slow trip passing through a mudited entry will dislodge practically no dust, a rapid trip will make air disturbance enough to coat the cars with fine dust. MR. PRYDE: We have used mudite on stoppings around a fire in Reliance and for two months thought they were getting good results, but the fire was found to be drawing air and to be spreading. This mudite was smeared over the stoppings with a trowel. After this apparently failed we used dry adobe.

Jan 1, 1925

By Kenneth Holmnerg

About 100 million terajoule is used annually worldwide to overcome friction and that is one fifth of all energy produced. The largest quantities of energy are used by industry (29%) and in transportation (27%). Based on our recent studies on energy use in passenger cars, trucks and buses, we concluded that it is possible to save as much as 17.5% of the energy use in road transports in the short term (5-9 years) by effective implementation of new tribological solutions. This equals to annual energy savings of 11.6 exajoules, fuel savings of 330 billion liters and reduction in CO2 emission by 860 million tonnes. In a paper mill, 15-25% of the energy used is spent to overcome friction. The electrical energy used by a paper machine is distributed as 32% to overcome friction, 36% for the paper production and mass transportation, and 32% is other losses. In paper machines, 11% of the total energy used to overcome friction can be saved by the implementation of new tribological technologies. This would result in electrical energy savings worldwide of 130,000 terajoule, economic cost savings of 2 billion euros and CO2 emission reduction of 11 million tonnes annually. An overview of the total energy saving potential by improved tribology in transportation and industry is presented.

Jul 31, 2018

By Carlos Berlini Filho

As inclusões exercem um papel fundamental na lingotabilidade dos aços produzidos em lingotamento contínuo. É conhecido na literatura o efeito da composição das inclusões na formação de obstruções em válvulas submersas. Contudo, um problema também recorrente no ambiente industrial é o desgaste dos tampões e válvulas submersas do distribuidor, que impede o controle de fluxo de aço para os moldes. O presente trabalho visa avaliar a influência da composição das inclusões na taxa de desgaste de tampão. Foram avaliadas inclusões de aços acalmados ao Si-Mn em corridas que apresentaram diferentes valores de desgaste de tampão. A partir dos resultados obtidos foi possível concluir que a taxa de desgaste de tampão é consideravelmente dependente do teor de MnO das inclusões e que um maior teor de Al2O3 pode contribuir também para reduzir o desgaste.

Aug 17, 2017

By Mark R. Pettitt

The results of an extensive research and development program to reduce the noise generated during coal cutting are presented. The characteristics and magnitude of continuous miner coal cutting noise sources are defined. This work consisted of development of a simulated coal ,cam to facilitate above-ground coal cutting tests, noise measurements in a reverberant acoustic chamber during simulated mining operations of a continuous miner (cutting the simulated coal scam), and noise measurements in an underground coal mine during continuous miner operation. In-mine and laboratory test results were in excellent agreement for both A-weighted overall levels as well as A-weighted one-third octave band spectra. Methods to reduce coal cutting noise are presented. These methods take full advantage of the dynamic characteristics of the forces generated during coal cutting. Dynamic cutting force isolation was shown to be a very effective technique. Finally, a continuous miner was equipped with a cutter head that incorporated (among other design factors) cutting force isolation. Successful, lung term, in-mine use of the cutter head demonstrated coal cutting noise at the operator's station of less than 90 dBA and 50% coal, 50% rock cutting of less than 93 dBA.

Jan 1, 1985

By Luiz Gabriel da Silva Nascimento

Foi fabricada uma matriz hipoeutética de Al-2%Ni e adicionado nela concentrações de 0,5; 1,0; e 1,5 % de nanotubos de carbono de paredes múltiplas (NTCPM). A fabricação do material estudado aconteceu por fundição e resfriamento unidirecional brusco originado grãos predominantemente colunares. Os ensaios mecânicos mostram que concentrações maiores de nanotubo na matriz provocam acréscimo na propriedade mecânica e que em áreas mais distante da base extratora de calor a microdureza aumenta. Na amostra que contém 1,5% de nanotubos o valor da microdureza em áreas da posição P1 distante 5 mm da interface metal/molde é aproximadamente de 120 HV, já em áreas da posição P5 distante 45 mm, se aproxima de 210 HV. A resistência a tração é influenciada pela adição de NTC. A matriz possui uma resistência a tração de 64 Mpa, enquanto que a adição de 1,5% de NTC eleva esse valor para 135 MPa.

Aug 17, 2017

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By Nicholas Kyriazi

The Bureau of Mines subjected three commercial compressed-oxygen self-contained self-rescuers to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The environmental treatments consisted of extremes of temperature and of shock and vibration. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. A critical concern was internal damage to an apparatus that would cause it to malfunction or seriously degrade its performance without any obvious external signs. The Bureau has previously tested chemical oxygen self-contained self-rescuers in a similar research program. Although the three compressed-oxygen units are not as sturdy as the chemical oxygen self-rescuers tested previously, they performed reliably after treatments on treadmill tests with human subjects and on machine tests using a breathing and metabolic simulator. Serious damage was caused by both the heat treat-ment of 71° C (venting of the 02 bottle in most cases), and in the shock treatment (breaking open of the case and dislodging of the components). When physical damage is obvious, a complete refurbishing of the damaged self-rescuer is recommended.

Jan 1, 1983

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By V. Svalbonas

In the establishment of a useful failure criteria for complicated, fabricated structures, two basic areas of knowledge must be evaluated: 1. The accuracy of the applied stress analysis must be known in comparison with actual stresses encountered during mill operation. 2. The metallurgical fracture properties of the basic materials must be established with reference to non-destructive examination (NDE) methods to be used during fabrication. Both of the above can only be evaluated by use of full scale tests on the structures, and/or components, of interest. This paper describes such tests and comparisons as applied to several large mill installations. In addition, weldment component fatigue tests arid flawed casting strain gauge tests are also discussed. The combination of such test results allows for the formulation of failure criteria directly applicable to the fabrication and examination procedures followed in grinding mill structure manufacture.

Jan 1, 1982

By Gabriella Cruz dos Santos Roza

Os aços 1Cr-Mo-V forjados são largamente utilizados em rotores de turbinas a vapor, e o seu desempenho em condições de fluência vem sendo melhorado por tecnologias de fabricação. Sendo assim, os fatores metalúrgicos que afetam o comportamento em fluência dessa classe de material vem sendo estudados. O objetivo deste trabalho foi a avaliar as diferenças na microestrutura e nas propriedades mecânicas, a temperatura ambiente, entre amostras de aço 1Cr-Mo-V fundidas em forno elétrico aberto e amostras que posteriormente refundidas no forno a arco elétrico a vácuo (VAR). As amostras foram forjadas a quente e tratadas termicamente em mesmas condições. Para a avaliação das diferenças, foram comparadas as microestruturas nas duas condições e feitas análises de inclusões através de microscopia ótica e microscopia eletrônica de varredura. Foram realizados ensaios de dureza e de tração a temperatura ambiente. Os resultados mostraram que a refusão foi eficiente na redução do teor de alguns elementos deletérios e na redução do tamanho e do número de inclusões, sulfetos de manganês e silicatos de manganês, além de contribuir para uma distribuição mais homogênea tanto das inclusões como da microestrutura bainítica apresentada. As medidas de propriedades mecânicas a temperatura ambiente não mostraram alterações significativas na resistência. Porém, houve aumento na ductilidade, manifestado por uma maior redução de área.

Aug 16, 2017

By David L. Brostrom, William C. Brice, Perry A. Canton

The business of mineral exploration and development has become much more than simply a problem of locating orebodies and designing mines. Favorable economic analysis of mining and processing feasibility is no longer sufficient to justify the development of a mine. New laws, enacted by virtually every level of government, require comprehensive land use planning, environmental analysis, mineland reclamation, mine safety studies, and many other considerations. This profusion of new laws says in effect, that the mining company is no longer responsible only to its stockholders. Mineral development today can be compared to a partnership. As in all partnerships, the risks and liabilities as well as the benefits are held jointly by all the participants. In addition to the mining operator, this partnership consists of the public, through its many levels of government, interest groups, and individual citizens. Therefore, you'd better know your partner very well - his responsibilities and capabilities. Mining is considered a high risk venture. The risk on the part of the operator and the lending institutions has long been recognized. The risk that the public and its government take in these mining ventures has now been recognized also. The people and their government have learned that they inherit, through abandonment or forfeiture, the mistakes and problems of individuals and companies regarding these natural resources. In looking through the "Mining Engineering Handbook" recently published by the Society of Mining Engineers, I noted that in their discussion of liability for excavations, the authors quoted from the book of Exodus, 20th chap., where Moses said to his people: "When a man leaves a pit open, or when a man digs a pit and does not cover it, and an ox or an ass falls into it, the owner of the pit shall make it good; he shall give money to its owner, and the dead beast

Jan 1, 1974

By S. V. Krishnan

Stability of fine quartz suspensions in process water is of concern in several mineral processing applications. In alkaline solutions, the presence of magnesium ions, arising from such sources as water hardness and magnesium-bearing minerals, leads to the precipitation of Mg(OH)2 which coats the surfaces of quartz. The conditions under which heterocoagulation or surface precipitation of Mg(OH)2 on quartz occur and the manner in which they influence the settling behavior of ground quartz was studied by means of settling tests, coating density determinations, zeta potential measurements and electron microscope observations. Coating density was greater when Mg(OH)2 nucleated on the surface of quartz than when the precipitates heterocoagulated on the quartz surface. The settling curves of quartz suspensions in the presence of different concentrations of MgCl2 exhibited a maximum of maxima which occurred at 10-3M MgC12 and pH 11. Interactions between quartz and Mg(OH)2, and flocculation-dispersion characteristics of quartz suspensions in this system are discussed.

Jan 1, 1983

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By George Mandarakas, Johan van Zyl, Karl-Heinz Becker

The world’s climate today has changed compared to 10 or 20 years ago. Many countries face water shortages; water sourcing for mining activities has become harder to secure. ESG’s focus on the industry has made us more aware of the need to preserve and responsibly use the water needed for wet processing in our milling and sorting activities. In a recent greenfield project in South Australia, 10 Gigalitres per annum would be required to process 5Mtpa of magnetite [1]. Published information indicates that the mining industry consumes approximately 12 EJ per year—or 3.5% of total global final energy consumption globally [2] or 3.33 trillion kilowatt hrs. This energy consumption is significant, considering the critical role mining plays in extracting and processing essential minerals for economic development and human progress. The perception of the mining industry is that not only does it consume significant power, but it also consumes a lot of the freshwater in the world. In fact, it consumes approximately 5% [3] of the total freshwater demand. According to the Intergovernmental Panel on Climate Change (IPCC), by 2050, 60% of the world’s population will be living in countries that are classed as water-stressed [3]. As more and more emphasis is placed on renewable energy sources, the amount of water used in mineral processing will increase because more and more raw materials require a water-intensive process. This increases the pressure on the mining industry to try and find water-saving initiatives. As part of this review, recent advancements in magnets have enabled magnetite processing facilities to achieve between 30 to 40% dry gangue material rejection before the wet beneficiation process (grinding and sorting). This reduction in energy consumption allows the reduction of energy consumption. Secondly, there is less material ground in the mills, which requires less water for mineral downstream processing.

Feb 1, 2025

By G. S. Hume

RECENT developments in the Turner Valley gas and oil field, 40 mi. southwest of Calgary, Alberta, have indicated a large producing crude-oil area. Drilling be¬gan in Turner Valley in 1913 but no major developments took place until the fall of 1924, when Royalite No. 4 well at a depth of 3740 ft. in the upper part of the Paleozoic (Mississippian) limestone obtained a production - of 20,000 M cu. ft. of gas with a content of about one imperial gallon of naphtha (73° A.P.I.) per M cu. ft. This well produced as much as 600 bbl. of naphtha per day, and until abandonment in 1934 produced 911,313 bbl., which together with the gas sold was valued at about $5,000.000.

Jan 1, 1937