Search Documents

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By M. Saghaeian, R. Hejazi, Fakoor Sanat Tehran Company, H. Abedini, M. Zare

"Dewatering of final tailings is one the biggest issues in iron ore processing plants. Because of the fine and hydrophilic particles in the iron ore tailings, dewatering of such material is difficult and, in most of the cases, needs to be processed using expensive and complicated equipment. In this study, a novel method based on classification of small and large particles has been proposed to improve the dewatering performance of iron ore tailings. In the proposed method, a hydrocyclone has first been used to separate the fine and coarse fraction of iron ore tailings. Then, the coarse fraction (hydrocyclone underflow) is easily dewatered by using vacuum belt filter. Then, the fine fraction (hydrocyclone overflow) is primarily dewatered by using a high rate thickener. Finally, the thickener underflow is added to the bed of solids on the same belt filter, which is used for dewatering of hydrocyclone underflow. The efficiency of this method has been compared with other solutions for tailings dewatering including changing vacuum filtration parameters, using fabric with larger pore size, and using pressure filtration, all through laboratory scale experiments on the tailings of an iron ore processing plant in Iran. The results indicated the superiority of this method compared to the other ones, which increased the specific filtration capacity of the tailings by around 46%.INTRODUCTIONWet beneficiation of minerals requires a substantial amount of water to enhance the efficiency of the process. Used water should be recovered at the end of process to minimize shipping costs, meet contract specifications, and reuse process water (Wills and Napier-Munn, 2006). Dewatering equipment is usually divided into sedimentation (thickening) and filtration (pressure and vacuum) equipment, the choice of which depends on particle size, solid content of slurry, and material nature (Mular et al., 2002)."

Jan 1, 2016

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

By David E. Pearson

"There are many tests that can be used to characterize and classify coals, and describe their quality. One of the easier tests, and most versatile in its application, is petrography. Rank and coal type are precisely defined by petrographic evaluation, and in this paper they are compared with other definitions of rank and coal type. Brief descriptions are given of the various rank tests, and of rheological and coking tests used to describe coking-coal quality in Canada. Similarly, tests used to evaluate thermal coal quality are discussed. Finally, the use of these tests as parameters to classify Canadian coals is examined with reference to four coal classifications.Introduction Among all coals there are two independent variables that are required to evaluate coal quality. These are, coal rank and coal type (or composition), and although coal petrography can be used to precisely define them, other methods are often used to provide values that are, in fact, functions of rank and coal type. For example, volatile matter yield is used as a proxy for rank, and free swelling index is used as a proxy for coal type in the International Classification of Hard Coals by type. Currently, there are a number of methods in use in Canada to define rank. The approach taken here, (obviously the author's bias), is that Romax, the mean maximum reflectance of vitrinite, is both a quick and an accurate measure of rank. It is logical to compare the other techniques employed in the measurement of rank to this favoured method. Coal type is, in theory at least, simply a quantitative measure of the various varieties of coal. In practice, the microscopic entities are assigned to a Reactive or Inert category, and at that point objectivity fades from petrography. Despite this somewhat subjective approach, petrographic composition of coals remains an independent variable of such.importance that its place in the evaluation of coal is essential. In this paper, a variety of me.thods that are used to assess rank and coal type are reviewed and compared; the influence of these variables over other parameters that are used to determine the quality of metallurgical and thermal coals is examined, and their usefulness in coal classifications is discussed."

Jan 1, 1985

By David S. Cahn

For many years the green and dry compressive strengths' of pellets have been, considered as possible criteria of pellet performance during induration. Although widely quoted throughout the industry, little attention has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of the test. The purpose-of this study was to compare the constant deformation rate test with that using a constant loading rate in addition, the dependence of these tests on such pellet properties as size, weight, and method of balling was to be investigated.

Jan 1, 1967

By C. C. Furnas

In the course of an investigation3 of the flow of gases through beds of broken solids the author obtained a number of data .on the specific volume of beds of broken solids of variously mixed sizes. A mathematical theory of the limiting conditions has been developed and some generalizations have been made for intermediate cases. A more definite knowledge of the relation between space occupied and size composition would be valuable to all those who are handling large quantities of broken materials. Such knowledge might be advantageously applied to the operation of a coke oven. For example, the output of the oven depends in general upon the number of pounds of coal which can be put in the oven at charging. It is known that the capacity of one battery of ovens was increased several per cent by slightly increasing the proportion of fine material in the charge.

Jan 1, 1928

By V. I. Lakshmanan, R. Roy

"TiO2 is used in paints, plastics, rubber, paper, inks, textiles and other miscellaneous applications. The demand for the pigment grade Ti02 is growing at 3.0%/year on average and this invites the development of innovative and cost effective processes. The current processes are not designed to recycle the reagents and thereby discharge the effluents into the environment, causing an environmental concern.During this study, synthesis of TiO2 from an ilmenite concentrate was investigated using an innovative atmospheric mixed-chloride leach process. The solution purification was carried out using solvent extraction in two stages. In the first stage iron removal was carried out and in the second stage titanium was extracted. The strip solution obtained from the second stage solvent extraction contained the purified titanium and from this stream pigment grade Ti02 was recovered. The barren solution was used for reagent recovery and the regenerated leach liquor was recycled."

Jan 1, 2011

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By Theodore Kessler

The purpose of this Bureau of Mines investigation was to determine what new organic compounds or high concentrations of a particular organic species can be formed by exposure of coal derivatives to ultrasonic energy. Tetralin, l-methylnaphthalene, and pyridine were used as model compounds. Gaseous and solid reaction products resulting from the ultrasonic irradiation of these coal derivatives were determined using mass spectrometry. Products from the irradiation of tetralin were studied as a function of time, atmosphere, and sample size. The sonolysis (chemical reactions produced by ultrasonic energy) of tetralin and l-methylnaphthalene produced C2H2, HCN, CH4, H2, CO, and CO2, depending upon the experimental conditions. The ultrasonic irradiation of tetralin also produced diacetylene under certain experimental conditions. The cleavage of organic chemical bonds by ultrasonic cavitation in the absence of water was also observed in this study.

Jan 1, 1967

By R. W. Lawrence

A high rate biological reduction technology has been developed to provide low cost hydrogen sulphide for various uses in water treatment and metallurgical processes. Commercial operations produce sulphide safely at a fraction of the cost of chemical sulphide. The biologically produced H2S is used for treatment of acid wastewater and selective metal recovery whereby metals present in wastewater streams are recovered in high grade metal sulphide concentrates that are sold to smelters. The combination of biological H2S production and selective metal recovery is currently marketed under the process name BioSulphide-Thiopaq. The process can be applied on a stand-alone basis or in conjunction with a conventional lime water treatment. Process advantages include: reduced lime treatment costs, reduced volume of waste sludge free of toxic metals leading to reduced long term environmental liabilities, selective recovery of metals and, in some cases, net profit from water treatment achieved through the sale of metal concentrates. Three case studies are presented to provide examples water treatment and metal recovery: the Caribou Mine, New Brunswick; the Phelps Dodge Bisbee operations, Arizona; and Falconbridge?s Raglan nickel mine in Quebec. A fourth case study is presented to highlight environmental control for treatment of ARD in the Leadville mining district of Colorado. Process flowsheets, capital and operating costs are presented for the four case studies

Jan 1, 2003

By John J. Jonas, Hong Qin

Cylindrical samples of pure titanium were subjected to uniaxial compression at room temperature, leading to the formation of three generations of twins. Many primary contraction twins were observed as the initial texture was favourable for their formation. Numerous secondary extension twins formed within the primary contraction twins and some tertiary contraction twins within the secondary extension twins. The orientations of these three generations of twins were determined by electron backscatter diffraction techniques and their associated Schmid factors (SFs) were calculated. The formation of the twin variants selected in each generation and the absence of certain potential variants are accounted for by rotating the twinning displacement gradient tensor expressed in the twin system reference frame into the crystallographic reference frame of the relevant neighbouring grain. The presence of the observed primary, secondary and tertiary twins is explained in terms of the ease of imposing the required accommodation strains on the neighbouring grains. By contrast, certain first, second and third generation potential high SF twins were absent because their formation would have required accommodation by the most difficult deformation mode: pyramidal glide.

Jan 1, 2015

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By Scott, Turner

MY whole life has been spent in the mining business, PO I naturally tend to address my remarks particularly to the newly-graduated mining and metallurgical engineers among you. To a certain extent, all forms of engineering principles are involved in the training of the mining engineer, and most sorts of engineering are certainly utilized by him, so every one of this graduatins class is concerned with the field I propose to discuss.

Jan 1, 1932

By L. Li, K. Jiang

China is the world largest producer and consumer of zinc. Beijing General Research Institute of Mining and Metallurgy (BGRIMM) is one of major research and engineering institutes for nonferrous metallurgy in China. This paper (presentation) introduces the development of China’s zinc smelting industry, key production processes and main producers. The process research and development are reviewed as well as BGRIMM’s R&D activities in the last decade. China's refined zinc production was 4,829kt in 2012, accounting for 38.6% of world production. Primary production was 4,722kt. There are around 150 refined zinc producers in China. The traditional fluid bed roasting - leaching jarosite is still a dominant process for primary production and its production accounts for about 60% of country's total production. However, the direct leaching process is gaining market share. Seven direct leaching plants with 330kt/a capacity, including autoclave leaching and the Outotec direct leaching, have been put into production by June 2013. Five autoclave leaching projects with 590kt/a capacity are in the pipe line and are expected to be commissioned in 2014 and 2015. To cut the production cost and improve smelter economics, process research to optimize the production flow sheet, to improve the iron removal and to enhance the recovery of co-existed rare metals were carried out. The development trends of China’s zinc smelting industry from the view of cutting production cost, improving energy efficiency, increasing comprehensive utilization are discussed accordingly.

Jan 1, 2014

By AIME AIME

QUALITY and size do not ordinarily go hand in hand, but there is good evidence that both these attributes reached a new peak at the Annual Meeting of the Institute in New York just concluded. Certainly, the total attendance of 2500 was far above any yet attained, as might be expected with the recent rapid growth of Institute member- ship. General comment indicates that the quality of the papers also was notable, though not measurable by so definite a yardstick as attendance. During the meeting 49 technical sessions were held, at which more than 250 formal papers were presented. In addition, there were some thirty special meetings of committees, Divisions, and other Institute groups. In reporting the Annual Meeting eleven years ago the statement was made that "unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger," and "the fifth floor, where a buffet lunch is served each day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size." Unfortunately the angel to succeed Andrew Carnegie, who financed the building of the present home of the Institute 35 years ago, has not yet ' appeared. Even if some one would merely build another elevator or two in the present building it would help. Fortunately, the modern auditorium of the American Radiator & Standard

Jan 1, 1940

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By A. M. Salomon de Friedberg

With respect to impurities, HBM&S' copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By L. R. Hougen

The Falconbridge Matte Leach Process yields high-purity nickel chloride by selectively dissolving nickel from copper-nickel converter matte with hydrochloric acid , purifying the solution by solvent extraction and crystallizing NiCl2 4H2O by further acidifying the purified leach liquor. In the Kristiansand Matte Leach Plant, a granular oxide is produced by high-temperature hydrolysis of the nickel chloride for subsequent reduction to a high-purity granular metal product, designated NICKEL 98. This paper describes the investigation of on alternate route to processing nickel chloride in which high-quality cathode nickel is produced by electrowinning from all- chloride electrolyte. The investigation was made in a pilot circuit containing two production-size electrowinning tanks operated in conjunction with the commercial-scale leach plant.

Jan 1, 1977