Search Documents

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By Garston H. Blackwell

For ageing open pit mining operations where the economic viability of another pushback is questionable, mine life can be extended by increasing the wall slope. If the steepening is started where ore intersects the pit wall, the capital outlay for waste stripping is minimal. Such a venture must be conducted safely, and a basic requirement would include loading equipment capable of working remotely. In the application described, alternatives in the choice of loader included equipment available on site, or the purchase and assembly of used equipment. Only electric cable shovels were in use at the operation, and it was thought that these would be more capable of digging high muck piles at the productivity demanded by an increasingly efficient mill, and in a challenging environment less suited to a rubber tired loader or hydraulic front shovel. A decision was made to convert an older electric cable shovel to remote controlled operation and to include the application of semi-robotic control. The conversion was completed successfully and is described, along with methods developed for remote operation of a shovel, and the application of various sensors for semi-robotic operation. A plan of operations to mine out several completed double benches and make two quadruple benches with wide catchment berms is depicted. On completion of this task, the working benches developed would be wide enough to operate at near full production. Prior to moving the remote controlled shovel back into the pit, a large wall instability became active, eventually closing the operation. The instability could have been safely mined using the remote controlled shovel.

Aug 1, 2013

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By Frédéric Flament

The aim of this paper is to present the development of a data validation software as component of a commercial mass balance package. Data reconciliation through mass balance is basically an optimization problem constrained by the law of mass conservation. As any optimization problem solved with a modern and robust software application, erroneous information or starting point will always lead to a solution, whether it is realistic or not. Moreover, good information wrongly weighted by an incorrect error model will lead to the same bad ending. In an industrial context where competition requires accurate information, data reconciliation without validation can be disastrous and calls for data validation before and after reconciliation. The challenge in automated data validation resides in the development of general theoretical solutions. Until now, none has been presented and only partial solutions are available. The development presented in this paper incorporates some of these partial solutions. The integration of human knowledge into the application paved the way to a more general solution. The combination ?theoretical validation ? human expertise? proved to be flexible and reliable enough to be integrated in a commercial data validation package. Numerous examples though industrial applications are presented. These applications demonstrate the validation of raw measurements, user support in the development of error models and validation of reconciled measurements.

May 1, 2001

By S. H. Chauvenet

HARRISBURG is situated on the Pennsylvania Railroad, one hundred and five miles from Philadelphia, two hundred and forty-eight miles from Pittsburgh, and ninety miles from Baltimore, and has running through it the Pennsylvania, Northern Central, Philadelphia and Reading, and Cumberland Valley Railroads, and the Pennsylvania Canal. Surrounded by a thickly settled farming country, from which to draw native labor, within easy distance of anthracite and bituminous coal, with ores and limestone near at hand, and with the Susquehanna River as a never-failing water supply, Harrisburg has advantages for manufacturing which warrant the investment of the capital that has already been made, and has a future as a manufacturing city second only to Pittsburgh and Philadelphia. THE PENNSYLVANIA STEEL COMPANY, L. S. BENT, SUPERINTENDENT. The works of this company, the largest in Harrisburg, lie between the Pennsylvania and the Philadelphia and Reading Railroads, on. the Pennsylvania Canal, and are essentially devoted to the manufacture of Bessemer steel rails. Capital stock, $2,000,000; invested in business, $5,000,000; wages per month, $80,000; employs 2000 men; capacity, 100,000 tons of rails per year, which is being increased to 130,000 tons. The plant, as it now stands, comprises five Bessemer converters, two 7-ton and three 8-ton converters, two 15-ton open-hearth furnaces in operation, and two 30-ton open-hearth furnaces in course of construction, one blooming mill, one rail mill, seven steam hammers, two blast furnaces in operation, two blast furnaces in course of construction, foundry, pattern $hop, machine shop, blacksmith shop, and frog shop, and merchant mill in course of construction. Bessemer No. 1 was built in 1865, with two 7-ton converters, 2 spiegel cupolas, 3 feet diameter, and 3 iron cupolas 6' 6" diameter,

Jan 1, 1882

By Vanderlei Beisiegel, Arthur L. Bernardelli, Arthur W. Ruff, John H. Tremaine

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 per cent iron, 2.2 per cent combined silica and alumina, and 0.05 per cent phosphorous on a dry basis. Hematite is predominant and no significant sulfur on other deleterious elements are present. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air.

Jan 1, 1974

By M. E. Hawkins

Mineral analyses and electrical resistivity measurements of 324 representative samples of oilfield brines from 24 oil-productive counties in Mississippi and Alabama are presented in tabular form. Results of the mineral analyses, which include calcium, magnesium, carbonates, bicarbonates, sulfates, chlorides, sodium, and barium (with strontium if present), are reported in milligrams per liter. Electrical resistivity measurements in ohm-meter2 per meter at 75° F are reported in ohm-meters in the tables. Chemical analyses of formation waters are helpful to operators having water problems associated with petroleum recovery; electrical resistivity values are helpful in making interpretations from electric logs.

Jan 1, 1963

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By Ofra Damm, v du Preez, D. van Vuuren, L. Simpson, H. Chikwanda

"South Africa is the world?s second largest producer of titanium bearing minerals, but apart from producing titanium mineral concentrate to form TiO2 slag, little further value is added in South Africa to mined minerals. Various studies were undertaken by both government and the private sector in an un-coordinated manner until 2007 when the South African Department of Science and Technology (DST) planned and adopted a national strategy to establish a local titanium metal industry through the research and development of key technologies that would provide a competitive advantage to such a local industry. The strategy entailed a two-pronged approach in the development of this capability, viz. simultaneous investments in the development of high-level human capital and technology in the fields of titanium metal powder production and downstream titanium metal powder processing technologies. To date significant progress has been made to establish research and/or pilot scale facilities in the following technical areas: TiCl4 production technology, titanium powder production technology, high energy milling of titanium powder, metal injection moulding facilities, rapid production of large components using laser additive manufacturing technology, investment casting of titanium, resource efficient machining of titanium and friction stir welding of titanium. Supporting technologies are also at an advanced stage through investments in titanium powder spheroidization and direct rolling of titanium powder. The intent with investment in some of these areas is not to develop new technology per se, but rather to establish local capability that will position South Africa to collaborate with other organisations in the world so that technologies can be acquired and transferred when needed in the future."

Jan 1, 2014

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988

By F. B. Plummer

PROGRESS during 1940 in oil-production technology has been confined largely to a steady advancement in practices inaugurated in previous years, rather than the introduction of any new startling process or technique. The usual changes, improvements and additions in production equipment have been introduced. An increased attention to, and interest in, research has been noteworthy, resulting in improved efficiency in operation of oil wells. control, utilization of reservoir energies and reduction of production costs.

Jan 1, 1941

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964