Search Documents

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By Wooltorton B

Highwall failures in surface coal mines in Queensland occur as circular slips through weak and weathered material, or as bilinear slides on sub-horizontal surfaces and steeply dipping joints. Weak horizontal planes occur in the Permian-Tertiary unconformity or on bedding surfaces within the Permian Coal Measures. Sub-vertical movements occur along rock joints and tension cracks induced by stress relaxation after excavation. Blasting also introduces new fractures and causes movement along existing rock discontinuities. Critical factors for stability include the dip direction of potential failure surfaces, shear strength of the rocks, damage due to blasting prior to highwall excavation, groundwater conditions, the type and performance of clays on shear surfaces, and pit geometry.

Jan 1, 1981

By Matheus Martini

A escória de aciaria LD é um coproduto abudantemente gerado através da metalurgia primária e secundária, sendo que após seu resfriamento e beneficiamento pode ser aplicado em diversos setores, mas que necessita ser submetido a processo de envelhecimento para minimização da expansão. Em geral, no Brasil, o Método PTM-130/78 é o mais utilizado para avaliar o potencial de expansão, entretanto o método leva 14 dias para obtenção dos resultados. Por meio de uma cooperação técnico-econômica entre a CSN e a EEL-USP, o método de expansão foi correlacionado com as fases identificadas e quantificadas por Difratometria de Raios-X e Método de Rietveld, respectivamente, além de compreender o mecanismo de expansão. Análises de regressão múltipla permitiram ajustar modelos matemáticos com 97,0% de ajuste e uma redução no tempo de ensaio de 14 dias (336 horas) para 7 horas.

Aug 16, 2017

By X. Tang, N. Ripepi

The Langmuir model has been widely used for the coal-methane sorption process through an isothermal test. However, even though the temperature-dependent Langmuir model was recognized theoretically and experimentally, the quantitative relationships between the Langmuir constants a and b and temperature have not been clarified and confirmed by laboratory test data. This paper collects 158 methane-coal sorption data under different temperatures that apply the Langmuir model to the relationships between the Langmuir constants a and b and temperature. Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters a and b. The results from these published isothermal tests indicate that (1) there is no consistent relationship between Langmuir constant a and temperature, (2) the Langmuir model is a temperature-dependent model whose temperature-dependent feature is mainly shown by the relationship between the Langmuir constant b and temperature, and (3) the relationship between the Langmuir constant b and temperature can be described by both exponential and linear relationships with dried coal. This paper provides a database for the temperature-dependent Langmuir model that can be used for the reservoir simulation of coalbed methane reservoirs and for the coal seam degasification modeling of underground coal mines, considering the heating effects induced by geothermal and heat injection through factors such as hot water, hot steam and ultrasonics.

Jan 1, 2016

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By W. C. Shanks

Metalliferous sediments and/or saline brines have now been discovered in numerous sea floor deeps along 900 km of the axial rift zone of the Red Sea (Fig. 1). The Atlantis II Deep remains the most interesting of the the brine deeps both in terms of intensity of submarine hydrothermal processes and in terms of potential economic importance. In fact, successful completion of a pre-pilot mining test in 1979 indicates that the Atlantis II Deep may become the first deep sea base metal sulfide mine (Mustafa and Amann, 1980). Under the most optimistic scenario, the Atlantis II Mine might be established 4-6 years after completion of a year long pilot mining test in 1983-84. If established, mining would produce about 100,000 tons per day of wet mud with about 200 tons per day contained zinc, and proportional amounts of Cu and Ag. Expected mine life would be about 15-20 years (Anon., 1981). In addition to direct economic importance, the Red Sea brines and metalliferous deposits provide significant insight into exploration for sea floor brine-related ore deposits and for analogous ancient deposits. In this paper I will concentrate on the economic potential of Red Sea deposits and sea floor exploration for brine related deposits, but some ramifications of relevance to ancient deposits are extant.

Jan 1, 1982

By Nils Eivind Kamfjord, Halvard Tveit, Ingeborg Solheim

"Because of its negative environmental effect the attention towards NO emissions increases. This again leads to new demands from the authorities for better surveillance and control of emissions. Earlier and recent industrial measurements towards FeSi- and Si-metal furnaces reveal quite high NO-emission. The NO is believed to be produced in the combustion zone above the furnace surface, mainly as thermal NO.In order to expand the knowledge on NO-formation in silicon metal production, a pilot scale experiment in a 440 kVA silicon furnace has been carried out. The experimental set-up was designed with a view to be able to copy and manipulate the formation mechanisms for NO by controlling the flow of false air into the off-gas system.The resulting NO-values corresponding to the different air inlet to the furnace top, show significantly differences between the different air inlet geometries.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2). Since combustion of fuels, such as gasoline, diesel, bio diesel, propane, coal, and ethanol, forms NOx the dominating contributors to NOx emissions are the on-/offshore transportation industry and power generation based on fossil fuels [1]."

Jan 1, 2012

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By T. D. Yensen

It is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current losses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that, indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use. Until the beginning of the present century, Swedish charcoal iron was regarded as the best grade of iron for magnetic purposes, and even now it ranks high among the various grades used. About that time Sir Robert Hadfield1 produced a number of iron alloys that revolution-

Jan 1, 1916

By C. Xiao, R. Chi

In recent years, the biosolubilization of rock phosphates by phosphate-solubilizing microorganisms has become a major topic of research studies. However, the microorganisms used in previous studies were mostly single and known species, and studies seldom focused on mixed communities of microorganisms or microbial consortia from natural environments. In this study, a microbial consortium from rhizospheric soil was used to solubilize two different compositions of medium- to low-grade rock phosphates — designated as ore samples 1 and 2 — in a laboratory-scale bioreactor. The microbial consortium showed good growth in the bioreactor, reduced the suspension pH and released soluble phosphates from the ores. Scanning electron microscopy with energy-dispersive X-ray spectroscopy showed the action of the microbial consortium on the ore surface. There was considerable corrosion on the ore surface, and 3.42 and 4.93 percent of the element phosphorus was removed from ore samples 1 and 2, respectively. Microorganisms were sampled from the bioreactor for the analysis of their community structures by Illumina MiSeq high-throughput sequencing. The analysis show that the suspensions added with different ore samples had different microbial diversities and richness. This study provides new insight into the biosolubilization of rock phosphates by a microbial consortium directly taken from rhizospheric soils.

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010

By Heidy de Oliveira Simões

O objetivo deste trabalho foi estudar as correlações entre o IPM (Índice de Permeabilidade Magnética) das pelotas queimadas, as trincas formadas durante o processamento das pelotas no pelotamento/endurecimento e o FeO de cada amostra. As análises evidenciaram que o tipo de trinca presente na pelota impacta no IPM fazendo diminuir a correlação entre IPM e FeO. O entendimento do fenômeno possibilitou desenvolver uma metodologia para determinação de um parâmetro que pudesse ser correlacionado ao FeO das pelotas de minério de ferro, estendendo sua aplicação ao pellet feed, baseado nas propriedades magnéticas do material. O método consiste em medir a variação da indutância de um solenoide, provocada pela introdução do material que se deseja determinar o parâmetro no núcleo de uma bobina, determinando-se relativamente a permeabilidade magnética das pelotas e pellet feed. Para tal, foi definida uma metodologia nas quais alterações devidas à variação da densidade da amostra, causadas principalmente devido a trincas nas pelotas, sejam mitigadas, garantindo a repetibilidade dos resultados. Assim, foi possível a determinação do FeO das amostras através da medição deste novo parâmetro, de forma mais rápida, fácil e com um custo consideravelmente menor que na química analítica clássica.

Aug 1, 2018

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968

By V. F. Petrov

Cyanide is widely used gold lixiviant for hydrometallurgical processes. The resulting tails contain complex toxic compounds. With reference to this, the protection of the environment should be the major issue. A complete detoxification of cyanides before disposal, a partial detoxification to the allowable concentrations and a disposal of tails at a polygon followed by the detoxification of excess water into the environment are offered as an environmentally friendly way of disposal. However, a complete detoxification of the cyanidation tails does not give the required results due to the presence of toxic compounds, cyanides and thiocyanates in tailings ponds. This is due to adsorption-desorption process occurring between solid and liquid phases. A partial detoxification is used to down cyanide to the allowable concentrations, which are safe to the environment. The storage of tails without detoxification is mainly used at low concentrations of toxic compounds in the disposed tails. With reference to this, water recycling is practiced by Russian plants in order to reduce as much as possible or almost eliminate toxic effluents into the environment. Fresh water is applied if necessary and to make up for water losses, with 8-12% of total water supply. This allows for the stability of water balance and the decrease of consumption of the reagents applied. The conditioning technologies of water recycling followed by regeneration of free cyanide and metals recovery as saleable concentrates are specially developed due to adverse impact of water recycling on gold recovery processes due to high concentration of base metals (copper). These technologies are also profitable. In order to detoxify cyanide in the tails for tailings dam, effective and inexpensive technologies involving a seasonal use of detoxified reagents were developed. For example, a technology with aldehydes use which is applied by a series of operations. Effluents disposed to the environment are detoxified using chlorination followed by almost a complete destruction of toxic cyanides and thiocyanates. Before disposal, chlorinated water is settled to precipitate the resulting hydroxides of metals and complete chemical reactions such as a full decomposition of hypochlorite ions. In order to protect ground water, watertight screens from local water-resistant materials are used. The samples of these materials were previously tested and chosen according to their maximum ability to adsorb toxic compounds in the tailings pond. If local water-resistant materials are not available, whole welded impermeable polymer screens are used. The options mentioned allow the storage of cyanidation tails in accordance with national ecological standards. Keywords: cyaninides, thiocyanates, wastes, environmental safety, recycled water-supply, detoxification, storage

Sep 1, 2012

By Terry R. Neumann

In 1987 and 1988, the U.S. Bureau of Mines conducted a mineral resource investigation of the 31,400-acre Muddy Creek Wilderness Study Area (UT-060-007). The investigation was requested by the Bureau of Land Management and authorized by the Federal Land Policy and Management Act of 1976 (Public Law 94-579). The study area is located in Emery County, Utah, about 50 air-miles southwest of Green River, Utah. The wilderness study area is in the San Rafael Swell region of the Colorado Plateau Physiographic Province. Rocks in the area consist of gently dipping sedimentary strata of Permian, Triassic, and Jurassic age.

Jan 1, 1988

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022