Search Documents

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By H. V. S. Tingley

My topic today is future trends in compensation for the mining industry. I seldom get the chance to speak about a subject of such immediate interest to an audience, so I would like to make the most of this opportunity by telling you that everybody in this room will become rich beyond his wildest dreams in the next few years. I would like to open my talk that way, but in compensation, like everything else, there is a great gap between dreams and reality. Back to reality. When we talk about compensation, we?d better define our terms because the compensation is really an umbrella for five basic types of payment made to management personnel. Slide 1 identifies these elements of compensation.

Jan 1, 1980

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilization neutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre.INTRODUCTIONProcessing gold-copper ores by cyanidation has been a cost-control challenge since the cyanidation process was first used in 1889. Copper cyanide is stable only in the cuprous state, not the cupric. This factor results in the oxidation of a mole of cyanide per mole of nonchalcocite copper extracted. Each mole of copper extracted forms a cyanide complex with a minimum of 3 mol of cyanide. This cyanide-to-copper mole ratio is required to dissolve gold. The oxidation of cyanide and copper complexation with cyanide results in high cyanide consumption for copper-gold ores, which is a significant operating cost.One challenge in processing gold-copper ore is the cost of cyanide related to the extraction of copper. Processing 10,000 t/d of ore containing 1,000 mg/kg copper and 10% copper extraction yields 1,000 kg/d of copper. Currently, processes to remove copper from cyanide leach solution treat either the total flow of the barren or a bleed of the barren. The two processes used for copper-gold ores are sulfidization, acidification, recycling, and thickening (SART), which produces a copper sulfide product for sale; and acidification- volatilization-neutralization (AVR), which recovers the cyanide from a gas and produces a low–cyanide content solution. This low–cyanide content solution can be recycled to the process or might require additional treatment before being disposed from the operation."

Jan 1, 2017

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By Florian Kongoli

Converters have been playing an important role in the extraction and processing of metals ever since the first type of converter was invented about 100 years ago. Historically their operation has been mainly based on the experience of talented operators rather than on strict control and optimization technologies. However, in the new realities of unavoidable necessity to increase productivity and in the conditions of diversification of primary materials from various geographical areas, improving control and optimization techniques have become indispensable. In this paper a review of the authors? previous work in terms of improving control and optimization of converter operational practices related to magnetite content and precipitation, slag and metal blows, problematic and dangerous elements such as As, Sb etc. has been described by highlighting the advantages that the new control and optimization methods and tools bring to everyday converter practices. Several examples are given and future work is underlined

Jan 1, 2005

By Roy J. Greenfield

The overall purpose of this research was to improve the understanding of how the post disaster seismic location system works, what determines the signal size, what is the character of the seismic noise, how well the system can detect blows from a trapped miner, and how well the source of the blows can be located. Based on an improved understanding of the system, improvements were suggested in the seismic subarray configuration, and in the system deployment procedures. An important part of this research was to become familiar with the seismic system operation and to work with the Westinghouse Electric Corporation and MSHA personnel to modify and improve the system. To accomplish this we participated in the planning, execution, and data analysis for a number of seismic field tests. Several in-mine field tests were conducted. From these tests the capabilities of an in-mine seismic system were analyzed and specifications were made for designing an operational in-mine system. Several portions of the work done on this grant were covered in previous reports. In particular the capabilities or the presently operational surface based seismic location system has been thoroughly documented by Durkin and Greenfield (1981). Portions of the location procedures and effects of mine openings on seismic signals have also previously been published. These portions or the work will only be summarized in this final report.

Jan 1, 1982

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By José Britti Bacalhau

Na conformação de plásticos de alto desempenho, cuja demanda cresce continuamente nos setores automotivo e de eletrodomésticos, é necessário aços com elevada resistência mecânica e excelente polibilidade. O aço DIN 1.2711 e suas modificações são materiais encontrados no mercado que atendem tais necessidades, porém não foram projetados para essa aplicação. O presente trabalho discute as características de um novo aço desenvolvido especificamente para moldes plásticos de alto desempenho. Foram produzidos em escala piloto, dois lingotes de 55 kg, sendo um deles o DIN 1.2711 que serviu de referência, e o outro com a nova composição química. A curva TRC dos materiais foi determinada por dilatometria, e sua usinabilidade avaliando o volume de material removido em relação ao desgaste da ferramenta de corte em fresamento. Caracterizações microestruturais por MO, MEV e dureza também foram realizadas. O Novo Aço apresenta elevada homogeneidade microestrutural e de dureza, boa temperabilidade e usinabilidade superior ao DIN 1.2711. A segunda etapa constou na produção de um bloco forjado em escala industrial a partir de um lingote de 35 toneladas, e na validação dos dados experimentais em empresas fabricantes ou usuários de moldes, as quais comprovaram a superior usinabilidade do Novo Aço em aproximadamente 50% ao DIN 1.2711. Devido à boa combinação de propriedades de manufatura o Novo Aço se torna uma interessante opção para o aumento da competitividade das ferramentarias e usuários finais de moldes plásticos.

Aug 16, 2017

By Charles L. Kusik

As part of an effort to establish the extent of the domestic chromium supply that could be exploited in case of adverse changes in international chromium production and trading patterns, a two-part study was conducted for the Bureau of Mines, to assess the domestic availability of critical metals in scrap containing significant amounts of chromium. This report describes the part of the study that deals with wrought stainless steels and heat-resisting alloys. Data were collected on types of scrap, sources, quantities, and ultimate disposition, leading to the conclusion that In 1917 about 62,000 tons of contained chromium was unrecycled. Unrecovered obsolete stainless steel scrap accounts for most of these uncollected chromium values. Error margins in the amount of uncollected scrap are estimated to be 10 to 20 percent.

Jan 1, 1980

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016

By David Keys

THE object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abun-dant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer,- but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite. No trace of magnetite was found. Fig. 2 is a photo-micrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titanium, 19.26 per cent; iron 45:41 per cent.

Jan 1, 1936