Search Documents

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By E. P. Carman

This: report gives data on the installation and operation of a packaged-unit heat-pump installation in a residence in McLean, Va., a suburb of Washington, D. C. The original equipment, installed in January 1947, was one of the first of 50 experimental Marvair units manufactured by the Muncie Gear Works, Inc., Muncie, Ind. The compressor unit of this installation was replaced by the company in September 1947, with a modified commercial model. The commercial unit and the original pump and fan accessories have been used as the sole means of heating (and cooling in summer! the. residence for the subsequent five winters and summers. The conclusions and data given herein, therefore, cover 6 winters sad 6 summers of heat pump operation, including 1 winter when temperatures averaged below normal for 2 months and the following summer when temperatures were above normal.

Jan 1, 1953

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By Henry H. Ginsberg

The effectiveness of 0.01 pct. molybdenum, as ammonium molybdate impregnated on coal, on the hydrogenation of a high-volatile bituminous C coal at 8,000 p.s.i.g. and 460° to 480° C. has been studied in a pilot plant by the Federal Bureau of Mines. Under these conditions, the Bureau obtained 98 to 99 pct. conversion5/ of coal to liquids and gases at throughputs of 29 to 101 lb. of m.a.f. coal per cubic foot of reaction space per hour. At 460° C. the indicated yield of oil ranged from 63 pct. (based on m.a.f. coal) at a throughput of 35 lb./c.f.h. (pounds per cubic foot per hour) to 68.5 pct. at a throughput of 58 lb./c.f.h., and the yield of gaseous hydro-carbons ranged from 25.5 to 19 pct. at the same throughputs. The maximum measured yield of oil boiling under 325° C. was 47 pct.

Jan 1, 1960

By Norman G. Foster

The mass spectra of 14 previously unreported alkylthiophenes are pre-sented. Low ionization voltage data of selected compounds from these 14 and 23 previously reported alkylthiophenes are presented and discussed for their value in supporting fragmentation mechanisms analytical correlations. A comparison with and corroboration of earlier correlations is made. Additional correlations concerning detection of side chain branching and the detection of ethyl-alkyl and propyl-alkylthiophenes are made. A discussion of the possible fragmentation routes and mechanism of fragmentation is given. Speculative structures are inferred s out some of the ions and hence this work provides a basis for suggesting fation mechanisms for the alkylthiophenes according to modern theories ass spectrometry. Verification of these mechanisms must await the availability of isotopically labeled molecules which are labeled in specific lotions that permit the definition of the paths of frag-mentation. Some suggestions for further work to generalize on the correlations and studies made to this point are presented.

Jan 1, 1965

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental, and technical aspects of open-pit mining operations. Factors influencing ore loss and dilution fall into two categories: (i) controllable factors like mine equipment selectivity and blast design and (ii) uncontrollable factors such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls pre-blast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, the study investigates the relationship between spatial entropy, cut-off grades, blast movement, dig-limits optimization model running time, and profit through a number of case studies. The results show that changes in cut-off grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution, and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy.

Nov 28, 2023

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Martin Hertzberg

In this Bureau of Mines study, an equation is derived for the limit burning velocity for divergent, spherical propagation from an ignition kernel of radius, r: (Su)e = ( ) . For flame propagation into a preexisting, stretching velocity gradient of magnitude dv/dx, the limit velocity is (Su)e = (a dv/dx)1/2. These formulations are shown to be equivalent to the fluid dynamic concepts of Damkoh1er, Kar10-vitz, and Markstein. Existing data for the b10woff limits of flames are shown to give excellent agreement with those concepts provided that proper account is taken of two dilution effects: composition dilution caused by entrainment and velocity gradient dilution caused by flow expansion. Approximate flow-field solutions are also derived for the unburned gas motion above an upward propagating, spherical flame kernel in buoyancy-induced flows. It is shown that;, the upward hemisphere propagates toward a stagnation plane in a counterflow configuration involving the balance between the combustion force, which accelerates the cold gas upward, and the buoyancy force that accelerates the cold gas downward. The position of the stagnation plane above the upward propagating hemisphere is related to the ratio of the buoyant velocity, vb, to the burning velocity, Suo Extinction of the upward propagating wave occurs by flame stretch in that counterflow configuration when n = Vb/Su begins to exceed the expansion ratio, Pu/Pb' and the wave is blown off by its own buoyancy-induced flow field.

Jan 1, 1984

By A. C. Hnatyshyn

INTRODUCTION THOSE concerned with coal mining operations in Alberta have been asked repeatedly the same question, "Why is mechanization in Alberta proceeding so slowly as to lag far behind the mines in the United States?" This question is often asked in such a manner as to indicate that a severe reprimand is overdue to the mining engineers of this Province for their apparent indifference to the problem of improving their mining operations by increased mechanization. To the average person, unacquainted with mining conditions and problems, mechanization appears to be simply a matter of introducing equipment to load coal underground and, once this is done, substantial economies in operating costs will automatically follow. Invariably, those who have followed this simple reasoning have found, to their regret, that such is not the case and that effective mechanization involves something more than the mere process of introducing loading equipment into a mine. To be effective, any programme of mechanization must take into consideration all operations incidental to the mining, transportation, and handling of the coal from the working face to the tipple, and must utilize equipment which can be best adapted to any peculiar condition or circumstance prevailing in the mine concerned. In the use of such equipment, the net and final result should be an improvement in operating costs of sufficient magnitude to at least return to the operator, over a specific period of years or during the expected life of that equipment, all his investment plus a fair return on that investment.

Jan 1, 1951

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits but this process is subjective and results in quantities of dilution and ore loss which can be improved upon to enhance the profitability of mining operations. Two weeks production data from a homogeneous Cu porphyry and heterogeneous Manto-type Cu deposit are used to assess the variability in the hand-drawn dig limits for 20 geologists, mining engineers, or ore control specialists and are compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine ranged by 3.7% from $10.5 million to $10.9 million averaging at $10.8 million. The percent range nearly doubled for the more heterogeneous mine at 5.9% from $17.9 million to $19.0 million averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9% increase) and $19.3 million (7.0% increase) for the homogeneous and heterogeneous deposits respectively. The natural variability, diggability requirement, and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Feb 23, 2024

By H. A. Baumann

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 1, 1950

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948