Search Documents

By Reginald E. Reid

Mining on Bureau of Land Management (BLM) administered lands is affected by Federal laws and regulations requiring the mining industry to plan for the environmental consequences of surface disturbance. Regardless of the requirements for obtaining a claim, permit, lease or contract to mine, a notice or a mining and reclamation plan will be submitted and an acceptable environmental document must be prepared prior to mining. A bond may be required based on the results of the environmental evaluation, public interest and the operator's past history of compliance. In several areas, Federal requirements are different from California's requirements under their Surface Mine and Reclamation Act (SMARA). Therefore, the BLM is negotiating with the State in order to work out problem areas of responsibility and duplication of effort.

Jan 1, 1984

By Omero Alonso-Gonzalez, Sergio Haro-Rodriguez, Ricardo Solis-Rodriguez, Francisco Alvarado-Hernandez, Juan Antonio Gonzalez-Anaya, Héctor Rene Vega-Carrillo

"Precious metals are currently associated with refractory minerals such as telluride (Calaverite, Sylvanite, etc.) and selenium (Naumannite Ag2Se), which are difficult to dissolve through traditional methods, therefore it is necessary to perform a pretreatment (oxidative or roasting) preceding the process of leaching by cyanidation. In this preliminary work the aim was to study the use of solvent extraction to remove tellurium and selenium ions from a synthetic cyanidation effluent, with the purpose of recycling the cyanide back to the process. For the extraction of these anions, TeO32- and SeO42-, tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (Amine F) were studied as extractants, using nonylphenol as a modifier in the organic phase (trimethylpentane). The results show that it is possible to recover 82% of selenium and 10% of tellurium from synthetic solutions containing either 20 mg/L Se or 20 mg/L of Te, respectively The Se or Te mole ratio to cyanide was 1:4.INTRODUCTION In relation to extraction of precious metals, the cyanidation process has been in use for over a century and despite environmental and toxicological problems it remains the most widely used and economical process available. In the late 90s, there were great efforts to recover gold and silver from refractory ores, which is difficult to do by simple cyanidation. To improve gold recovery from tellurides and selenides that occurs in some new mines, the ores are pretreated by roasting. This is one of the most effective ways of rendering refractory gold ores leachable as well as being a fast pretreatment process compared with bio-oxidation or pressure leaching (Aylmore, 2001). The most important tellurides minerals are Calaverite (AuTe2) and, Silvanite (Au, Ag)2Te4). In the case of selenides, minerals include Naumannite (Ag2Se) and Aguilarite (Ag4SeS) (Ostroumov et al., 1989). Examples of deposits containing telluride include La Bambolla Mine (Sonora, Mexico), Cripple Greek (Colorado, USA), and Kalgoorlie (Western Australia) (Aguayo et al., 1996). The main purpose of this work was to explore the feasibility of using quaternary ammonium salts such as: tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (amine F) to extract tellurium and selenium anions from aqueous synthetic cyanidation effluents, so that the cyanide solution could be recycled back to leaching process. The tests were performed on synthetic solutions similar to those found in a mine: 20 mg/L Te as TeO32-, 20 mg/L Se as SeO42- and mole ratio to cyanide was 1:4. using an alkaline medium with pH ranging from 8 to 12. Two aspects are evaluated in this paper:"

Jan 1, 2017

By Michelle Lacerda Sales Marques

A busca de novas rotas de beneficiamento que possam maximizar a recuperação metalúrgica e mássica é uma constante na Vale. O trabalho foi desenvolvido em três fases, onde foram estudadas quatro rotas de beneficiamento que buscaram reduzir a geração de ultrafinos e, assim, aumentar a recuperação mássica. Foram avaliadas rotas com pré-concentração do minério em concentração magnética (rota denominada PCM) e flotação (rota denominada MFMF), e uma rota onde a moagem mais grossa (P80 0,15mm) permite uma menor geração de ultrafinos (rota denominada MDMF). Esta última apresentou um CAPEX 6,5% menor quando comparado a rota PCM.

Aug 1, 2018

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By Xiao-dong Xiang, Hong-bo Jin, Ming-sheng He, Huo-guo Pang, Can-hua Li

The specification of the steel slag aggregate will be mutated if the ag- gregate is prepared by a single type crusher. The specification stability of the steel slag improved significantly when the jaw crusher and the cone-crusher are com- binedinthecrushingprocess.Thecombinationofthecrusherandscreenisapplied to produce steel slag aggregate while the roller washing process for removing the dustfromthesurfaceofaggregate.Apilotproductionlinehasbeenestablishedby this technology. The specification stability and the road performance indicators of thesteelslagaggregateshavebeengreatlyimprovedbythispilotproductionlineas compared with the traditional production line. The particulate of the steel slag aggregate is decreased by 81% compared to the traditional line. (cid:1) (cid:1)

Mar 1, 2018

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Rodrigo Vitorino da Silva

Ligas a base de zircônio utilizadas na indústria nuclear estão sujeitas à formação de hidretos que são causadores de efeito deletério no material. Para aumentar o tempo de operação desses componentes, é necessário o desenvolvimento de novas ligas que retardem ou diminuam esse efeito. Este trabalho tem como objetivo avaliar a influência da adição de elementos de liga em uma liga inédita a base de Zr-Nb na absorção de hidrogênio, através de testes que avaliam a absorção de hidrogênio e a formação de hidretos no material após processamento termomecânico e comparar seu desempenho com duas ligas comerciais. Para tal, foram realizados ensaios de microdureza, cinética de absorção de hidrogênio e micrografias. Os resultados de microdureza Vickers das três ligas estudadas, após o processamento termomecânico, são muito próximos. As curvas de cinética de absorção de hidrogênio mostram que a liga Zr-Nb-Sn-Fe apresenta melhor comportamento que as demais uma vez que o tempo para o início de absorção foi maior. As micrografias indicam que a liga proposta apresenta um desempenho superior em relação à morfologia dos hidretos visto que os mesmos são mais curtos e alinhados.

Aug 17, 2017

By Henry H. Ginsberg

The Federal Bureau of Mines made pilot plant investigations of the process requirements necessary to produce heavy fuel oil by the liquid-phase hydrogenation of bituminous coal. The investigation was carried out in three separate series of experiments. The first series studied the effect of temperature and contact time on product distribution at 3,500 p.s.i.g. and 420° to 480° C. in the presence of 0.1 wt.-pct../ stannous sulfide plus 0.05 wt.-pct. iodoform based on gross coal. As a result of increased contact times and temperatures, the conversion-6/ and yield of hydrocarbon gas increased, the viscosity of product oil decreased, and elimination of oxygen, nitrogen, and sulfur from coal increased. The yield of oil did not indicate any definite trend with changes in temperature and contact time. The yield of oil ranged from 76 to 85 pct. for Pittsburgh coal and from 60 to 85 pct. for Rock Springs coal. Asphaltenes in the product oil ranged from 17 to 38 pct. of the total oil for Pittsburgh coal and from 12 to 22 pct. for Rock Springs coal. Fuel oils meeting Bunker C or American Society for Testing Materials (ASTM) Grade 6 specifications were produced with Rock Springs coal at 0.2- to 1.0-hr. contact time and 440° to 480° C. and with Pittsburgh coal at 0.3- to 1.0-hr. contact time and 420° to 460° C. In the second series of experiments tin, nickel, iron, and zinc were evaluated as catalysts for the hydrogenation of Rock Springs coal to heavy fuel oil at 3,500 p.s.i.g. and 460° C. Using the apparent conversion of coal as criterion of catalyst activity, at a contact time of 0.45 hr. tin was the most effective catalyst; nickel and iron were nearly as effective, but the use of zinc resulted in much lower conversion. When the contact time was increased to 0.80 hr., the apparent conversion of coal was essentially the same for each of the catalysts. When the yield of oil boiling below 3550 C. was used as criterion of catalyst activity, at 0.45 hr. the order of activity was tin, iron, nickel, and zinc; at 0.80 hr. tin was far superior and the others were essentially equal. The product oils contained from 8 to 20 pct. asphaltenes.

Jan 1, 1960

Producing robust agglomerates with desirable structural properties is the key to success of the heap leaching of complex, low-grade nickel laterite ores. Mechanically strong but porous agglomerates with narrow size distribution (e.g., 5 ? 40 mm) are required to build permeable and perennially stable heaps of 4 ? 10 m height. The characterization of granules? microstructure is essential for greater understanding and correlation with the concomitant mechanical properties and robustness. In this study, we used non-destructive, computed X-Ray tomography analyses and scanning electron microscopy (SEM) in tandem with conventional compressive strength,and integrity/stability tests to draw links between nickel (Ni) laterite agglomerate strength/stability, internal microstructure (e.g.,porosity, inter-particle bridges) and binder type. It is shown that binder composition (e.g., tap water vs. 30% w/w H2SO4) and post-agglomeration drying both significantly impact on granules? physicochemical and microstructural properties. Acidic binder, in contrast with tap water, leads to significant incongruent leaching of different species from particles during ore-binder mixing and agglomeration. Upon wet agglomerate curing, solidified/recrystallized leached species form strong intra-granular solid bridges which, lead to greater compressive strength of dry agglomerates. Structural stability/integrity of cured agglomerates in acidic solution, however, decreases dramatically due to greater porosity and acid solubility of intra-granular solid bridges. These findings are useful in shedding more light on agglomerate structure characteristics and their optimization for enhanced column and heap leaching with concentrated sulphuric acid.

Sep 1, 2012

By Ricardo dos Santos Oliveira

Devido ao grande aumento da concentração de gases do efeito estufa, a criação de uma energia limpa tem sido um desafio para a ciência e as indústrias. Após identificar possíveis soluções para este problema uma alternativa seria a utilização de biomassa vegetal com capacidade térmica como fonte energética redutora no processo de redução do minério de ferro em altos-fornos. Este trabalho teve como objetivo utilizar capim elefante (Pennisetum purpureum) e carvão mineral na injeção de finos pulverizados pelas ventaneiras de altos-fornos nas siderúrgicas a fim de reduzir custos da produção de ferro gusa e reduzir a dependência de combustíveis fósseis no processo. O capim elefante é uma fonte renovável e de rápido crescimento que através da fotossíntese captura o CO2 da atmosfera, reduzindo a poluição causada pelos altos-fornos. Para simular a injeção dos materiais estudados foi construído na Escola de Minas - UFOP um modelo de partículas de combustão para analisar as amostras. Outras técnicas são utilizadas para caracterização como combustão, calorimetria, análise de gás, análise química imediata e elementar. Assim, em teoria, esta pesquisa mostra que o capim elefante misturado com carvão mineral através de sua injeção em altos-fornos mostrou-se viável em termos metalúrgicos e ambientais.

Aug 17, 2017

By Juver Vélez

Este método de exploración consiste en la introducción con un equipo mecánico - hidráulico que ejerce presión y rotación sobre un tubo de metal el cual tiene en su inicio una corona con diamantes impregnados (denominada broca), al interior de la corteza terrestre, con el objetivo de extraer el material roca de profundidades a la superficie para realizar su identificación geológica y análisis varios; La perforación diamantina ha venido desarrollándose a través del tiempo y con la experiencia de los operadores, llegando a crear máquinas de gran capacidad para alcanzar grandes longitudes.

Sep 1, 2017

By Daniel Codo de Faria

O desafio de se extrair conhecimento prático das enormes massas de dados disponibilizadas pelos sistemas de informação e automação nas indústrias já vem sendo discutido e enfrentado há anos. Neste contexto, a aplicação de técnicas de analítica avançada se apresenta como uma solução poderosa, capaz de mudar a operação dos processos industriais. Especificamente, a área de analítica preditiva é constantemente considerada como uma nova revolução para a indústria. Combinando técnicas como análise estatística, mineração de dados, “big data”, aprendizado de máquina e inteligência artificial, a analítica preditiva gera modelos a partir de dados históricos com o objetivo de prever condições futuras. Tal predição permite que ações de correção ou otimização possam ser definidas e executadas antecipadamente e com maior precisão, aumentando significativamente a eficiência dos processos, seja em relação a produtividade, custo ou qualidade. Este trabalho apresenta os fundamentos da analítica preditiva e uma aplicação prática na indústria. As técnicas utilizadas podem ser diretamente replicadas nas mais diversas áreas da indústria e para os mais diferentes problemas, evidenciando o forte potencial de expansão esperado para os próximos anos.

Aug 17, 2017

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By J L. Stacey

The diverse priorities, drivers and concerns of multiple stakeholders in the minerals industry complicate the integration of sustainable development considerations into mine design, as well as operational and strategic decisions. The ability of the industry to address all role-playersÆ needs, or indeed, to achieve consensus among all role players on the plethora of sustainable development issues seems a noble yet unattainable goal. One of the difficulties in assessing the relative importance of sustainable development issues across many stakeholders is the inevitable lack of impartiality in valuing these issues. Starting from a premise that transparency and fairness of the process are absolute prerequisites for progress, but that consensus is not, an approach has been developed in which all stakeholders are asked to assess the importance of all other stakeholdersÆ priorities, excluding their own. The approach recognises that stakeholders have different levels of contribution, understanding, vested interests, and perceptions of legitimacy and entitlement, across the diversity of sustainable development issues and decision criteria. Using Triangular Value Analysis, the relative weightings of each of the stakeholderÆs priorities are determined through a regression-like technique. The uniqueness of this approach is the manner in which self-assessment bias and overemphasis of stakeholdersÆ own priorities are avoided. The methodology can be used for both internal and external stakeholders, and in conjunction with other group decision making techniques, such as the nominal group or Delphi techniques. This paper will illustrate how Triangular Value Analysis may be applied in the minerals industry to determine priorities in various decisions relating to potentially conflicting sustainable development priorities within the industry.

Jan 1, 2009

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By Brian Metcalfe, Kord Wissmann, Gianni Martinez

The Middle East consists of vast deserts that reach temperatures up to 50 degrees Celsius, with some areas characterized by endless sand dunes. When the project team selected the location for a large new transportation project, little did they know that the site would be characterized by soft, nearly normally consolidated silt and clay extending below a thin sand crust. Searching for solutions, the design team elected to reinforce the subsurface with Rammed Aggregate Pier® (RAP) ground improvement elements and desired verification that the novel method would stand the test of prolonged static loads. Because the concrete pavements would serve to spread the load, a “zone load test” was performed, consisting of applying a uniform bearing pressure of 150 kPa over a 7.5m square concrete footing. Unlike individual pier load tests, the zone test allowed the project engineers the opportunity to confirm design parameter values under large-loading area conditions, a situation not often available to most designers. This paper presents the results of the zone load test whose results may be interpreted to better understand design parameter values. This paper is of particular significance because it adds a value contribution to the relatively few numbers of “group load tests” available in the literature for ground improvement applications.

May 1, 2022

By Giulio Rodrigues Altoé

Fibras de fique (Furcraea Andina) estão entre as lignocelulósicas naturais com grande potencial para utilização em compósitos poliméricos. O presente trabalho avalia a resistência ao impacto deste tipo de compósito com matriz epoxídica reforçada com diferentes percentuais de fibras de fique. As fibras foram embutidas sob pressão em mistura com resina epóxi DGEBA/TETA curada à temperatura ambiente por 24 horas. Os corpos de prova normalizados foram confeccionados com percentuais de até 30% em volume de fibras de fique alinhadas ao longo de todo o comprimento, estes corpos de prova foram então ensaiados em pêndulo de impacto Charpy e as superfícies de fratura analisadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumentou substancialmente com a quantidade relativa de fibra de fique reforçando o compósito. Este desempenho foi associado à dificuldade de ruptura imposta pelas fibras bem como ao tipo de trincas resultantes da interação fibra de fique/matriz epoxídica que ajuda a absorver a energia do impacto.

Aug 17, 2017