Search Documents

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

By E. H. Illsley

This bibliography is the first report of a Bureau of Mines research project on thermoelectric materials. Interest in such research has increased because of recent success in the design of commercial products, including generators and refrigerators, using the principles of thermoelectricity. This success made possible by the discovery of semiconductors that have much higher [effincies] than the metals and alloys formerly studied. Thermoelectricity is a term that includes a large number of phenomena relating heat to electrical energy. However, the moat important applications arise from two effects discovered by Seebeck in 1822 and by Peltier in 1834. When pieces of two unlike materials are joined at their two ends to form a continuous circuit, both of these effects may be observed. If the two junctions are maintained at different temperatures, an electromotive force known as the Seebeck voltage is generated. If, on the other hand, a current is made to flow through the circuit, the junctions of the materials will be found to differ in temperature. This phenomenon is called the Peltier effect.

Jan 1, 1959

By Jack Levin

Dr Laurence AlIison Bushel, a former President of the Chemical, Metallurgical and Mining Society of South Africa, now The South African Institute of Mining and Metallurgy, was born in Queenstown on 20th June, 1910, and died in Johannesburg on 4th November, 1991. There were three distinct periods in the career of Laurie Bushel, each enlivened by some special interests or achievements.

Jan 1, 1991

British Coal's Selby Complex is the newest producing mine in the United Kingdom. The reasons behind its origins, planning and design are explained. Some detail is given of equipment used, with the emphasis being placed on the unique features of its layout. The entire project has been planned and constructed over many years and the design has consequently changed, principally in response to the geology of the coalfield and improving technology. In spite of many totally unexpected difficulties, the mine, which is not yet in full production, has the highest productivity in the United Kingdom.

Jan 1, 1991

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

By Maria Carolina Andrade Teles

Uma fibra natural apresenta características interfaciais com matrizes poliméricas que favorecem a absorção de alta energia de impacto da estrutura compósita . Este trabalho procura avaliar a resistência ao impacto deste tipo de matriz de poliéster com reforço de fibras naturais. As fibras de Fique foram misturadas com resina de poliéster sob pressão em um molde metálico, e curada à temperatura ambiente durante 24 horas . Amostras padrões foram preparadas até 30% em volume de fibras Fique alinhadas ao longo de todo o seu comprimento, estas amostras foram então testadas com ensaio de impacto Izod do pêndulo e as superfícies de fratura examinadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumenta substancialmente com a quantidade relativa de fibra de Fique como reforço do compósito . Isto pode ser atribuído a uma descolagem preferencial da interface fibra / matriz , o que contribui para uma elevada energia absorvida.

Aug 17, 2017

By Betânia Mendes Sena

Neste trabalho é apresentada a influência de diferentes processos de tratamentos térmicos sobre as microestruturas e propriedades mecânicas resultantes em tubos de um aço sem costura do tipo API 5L. Após tratamentos térmicos, o material foi estudado em três condições diferentes: apenas laminado, normalizado e temperado e revenido, objetivando obter os graus X42R, X42N e X70Q, respectivamente. Ensaios de tração, dureza e impacto foram utilizados para caracterizar o comportamento mecânico dos diferentes graus do aço. Técnicas de microscopia eletrônica de varredura foram utilizadas para caracterizar as microestruturas resultantes dos tratamentos térmicos e as fractografias dos corpos de prova de tração e impacto. Os resultados mostram que tubos de aço sem costura do tipo API 5L não precisam ser de graus tão elevados quanto os tubos soldados, pois graus intermediários relativos aos tubos sem costura possuem propriedades mecânicas similares aos elevados graus de aço relativos aos tubos soldados, o que evidencia a vantagem da rota de fabricação de tubos sem costura.

Aug 17, 2017

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

Prof. J. C. BRanner, Stanford University, Cal. (communication to the Secretary): On p. 398, Mr. Hedburg mentions Marionite and Brannerite as ores of zinc. Neither of these has been authoritatively recognized as a distinct mineral species. Marionite, originally described by Elderhorst, was subsequently determined to be nothing else than hydrozincite. Analyses of the so-called Brannerite were sent by me to Prof. Penfield, who says it is a mixture of Smithsonite with some other mineral. On p. 398, Mr. Hedburg says the zinc-bearing formation of North Arkansas " is recognized as the Upper Silurian." So far as my observation goes, the ores occur both in Lower Carboniferous and in Ordovician or Lower Silurian rocks, but nowhere in rocks known to be of Upper Silurian age. If Mr. Hedburg has any paleontological evidence of the Upper Silurian age of these rocks, or of any of them, he will confer a favor upon geologists by making it known. On the same page is another statement in which I cannot concur. He says that in this region, " it can easily be seen that the largest fissure-deposits have been eroded and washed away, leaving here and there a few patches adhering to the hillsides." I am compelled to say that in many years' study of the geology of the region in question, I have never been able to recognize such a state of affairs as Mr. Hedburg here describes. The patches which he regards as remnants of fissure-veins, " adhering to the hillsides," I have found to be either the edges of bedded deposits, or portions of the zinc-bearing breccias, formed along old drainage-lines, and laid bare by the ordinary processes of erosion. That fissure-deposits have been partly removed by the same agency, goes without saying; but it is, in ,my judgment, no more true of North Arkansas than of any other mining-region that erosion has selected and washed away " the largest " deposits. My own views of the region in question are given in detail

Jan 1, 1902

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By T. A. Sullivan

The Bureau of Mines investigated modified sulfur concretes as one part of a program for utilizing sulfur in construction materials. The use of modified sulfur was studied as a means of preventing the stressing action in the concretes caused by the allotropic transformation of sulfur on solidification. Unmodified sulfur concretes have been prepared that have compression, flexural, and tensile strengths equivalent or better than Portland concretes. However, most of these concretes have been vulnerable to deterioration by weathering, temperature fluctuations, and freeze-thaw cycling. The sulfur was modified by reaction with dicyclopentadiene or dipentene before use as an aggregate binder. Sulfur concretes and modified sulfur concretes were pre-pared from acidic and basic type aggregates. Physical properties of the optimum mixtures were determined and compared with each other and with Portland cement concretes. The best results were obtained by reacting sulfur with 5 pct dicyclopentadiene to prepare modified sulfur concretes. Field testing of the concretes are in progress. Present results show that modified sulfur concretes are superior to unmodified sulfur concretes and equal or better than Portland concretes in compressive, flexural, and tensile strengths. Long-term aging characteristics of both modified and unmodified sulfur concretes are being determined.

Jan 1, 1976

By W. W. Fowkes

The Federal Bureau of Mines examined a low-temperature tar obtained from a small-scale commercial unit for carbonizing North Dakota lignite for products that might be important to the economic processing of the tar. Tie tar may be divided into three distinct parts: (1) Tar acids, 45 volume-percent; (2) tar bases, 1 volume percent; and (3) neutral compounds, 54 volume-percent. It has a boiling range of approximately 150° to 380° C. (the decomposition temperature) and yields 18 weight-percent as hard pitch. The tar distillate up to 365° C. may be separated as: (1) Tar acids, 48 volume-percent; (2) tar bases, 1 volume-percent; and (3) hydrocarbons, 51 volume-percent. The tar-acid distillate, boiling to approximately 265° C., was characterized in some detail; the neutral fractions and the tar bases were less thoroughly examined. In general, as might be expected of a primary low-temperature tar, the lower boiling fractions are less in quantity compared with the usual high-temperature tar. The homologous series of each major class appears to be rather complete, although some components are present in very small amounts. The tar is quite unstable thermally, and might be more conveniently processed by extraction methods rather than by distillation procedures. The neutral fraction of the tar is highly aromatic, and might be considered as base stock for the production of liquid fuels.

Jan 1, 1961