Search Documents

By M. du Plessis, J. P. Gouvea

Mesh based areal support is commonly applied in South-African deep-level gold mines. It forms part of an integrated support system that can cater for both rockfall and rockburst incidents. The application has been successfully applied over many years. Operations have different geotechnical conditions and practical considerations, which has led to the development of various types of mesh and integrated mesh-based support systems (i.e. meshing and lacing versus welded or chain-link mesh sheets). Typically rolls or sheets of mesh is pinned with rockbolts to the surface of an exposed excavation. Applications vary from hangingwall coverage in a conventional stope gully to complete excavation coverage in footwall drives of conventional mines or on-reef drives in massive mechanised mines. It is however critical to understand the behaviour of the rockmass and apply suitable support systems.

Apr 26, 2022

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.&apos; The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

El presente trabajo describe el sistema y los métodos para la extracción del oro en la planta de beneficio de Andaray Gold Mines, alcanzando una productividad óptima en el campo metalúrgico. La mina está situada en San Juan de Chorunga, provincia de Condesuyos, departamento de Arequipa, donde sus yacimientos mineralizados son de dos tipos: los yacimientos descompuestos que contienen limonita y oro libre, perteneciente a la mina Mercedes , y los de mineral piritoso aurífero, que comprenden chalcopirita y ojos de galena, perteneciente a la mina San Juan. El proceso de explotación se inicia con el transporte del mineral hasta su descarga en la parrilla de apertura. E mineral que no pase por la parrilla, se deriva a la chancadora durante 10 horas. Posteriormente pasa por la molienda para luego ser clasificado. Allí se adicionan los reactivos para la flotación y su análisis de malla. Producto de la flotación se obtiene el concentrado. El filtrado de los concentrados conlleva su envío a la molienda secundaria durante un período de seis horas. En este estado, la partícula de oro se encuentra limpia y en óptimas condiciones para la amalgamación y cianuración, donde el mercurio y la amalgama son exprimidos en una lona, destilándose, y se procede a la solución del oro, respectivamente. El método seguido es la agitación neumática, que suelta aire comprimido para la elevación del concentrado por el tubo elevador. Prosiguen los efectos de decantación, operación, control del cianuro y del alcali libre, precipitación, clarificación, limpieza y función de los precipitados. En el laboratorio se realiza el control de muestras del circuito de flotación, cianuración y de las barras, utilizando los métodos de soluciones de cianuro, ensayo de concentrados, minerales de mina, cabeza y relaves y ensayos de los precipitados. Finalmente, los cuadros de consumo de reactivos, mostrarán la eficacia del sistema y los resultados económicos de la planta de beneficio, como los costos, eficiencia de plata y mano de obra.

Jul 20, 1957

By Ajit Kumar Jaiswal

"Electric Arc Furnace (EAF) being a power-intensive equipment, EAF based industries are highly dependent on scarce electric energy. This is the reason Government of India is highly concerned about this and laid emphasis on the conservation of electric energy.This paper highlights factors contributing to reduction in specific electric energy consumption in EAF and suggests measures not only for power saving, but also for productivity improvement. To name a few, these are proper sealing of furnace, introduction of oxy-fuel burners, foamy slag practice, increased usage of hot metal/DRI, post-combustion of CO gas for preheating of scrap, improved selection & design criteria of electrics, power demand management, and process automation. Few cases also have been cited, where the above measures have helped in reaping significant benefits.IntroductionFor a long time, Government of India had focused on increase in energy supply, in particular, through electricity generation. Now the emphasis of Government of India has shifted from electricity generation to its conservation for following two reasons:??Power plants have become very cost-intensive??By saving energy, more of it can be delivered at lower cost to the consumersPower generating units, transmission & distribution agencies as well as consumers all have roles to play in the area of energy conservation. By energy conservation, we mean curtailing energy requirement by reducing energy wastages and taking up measures to improve energy efficiency of electric equipment/appliances. In almost all cases, this would be economically beneficial.India’s cost-effective energy conservation potential has been estimated by the Planning Commission at 23 per cent of total commercial energy generated ?1?. A national movement for energy conservation can significantly reduce the need for fresh investment in energy supply systems in coming years. It is imperative that we make all-out effort to realize this potential. Whether a household or a factory, a small shop or a large commercial building, a farmer or an office worker, every user can and must make this effort for his own benefit and for the nation’s benefit as well."

Jan 1, 2009

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By J Zhang, R Dimitrakopoulos

A two-stage stochastic mixed integer non-linear program is formulated for a mining complex to optimise strategic and tactical plans. The objective is to find the near optimal decisions for a mineral supply chain in the context with uncertainties in both ore supply and the commodity market (price and demand). The endogenous spot price in the commodity market and long-term sales contracts are considered in the formulation of the mining complex’s optimisation model and an ad hoc heuristic is developed to deal with the throughput – and head-grade-dependent recovery rate in processing plants. Numerical results indicate that the proposed heuristic is effective and efficient in numerical tests. Based on the proposed model and heuristic, a long-term contract design strategy is proposed for making decisions on the contract price and strategic investments. A shadow price based method is also proposed to evaluate the existing mining schedule.CITATION:Zhang, J and Dimitrakopoulos, R, 2014. Optimising a mineral supply chain under uncertainty with long-term sales contracts, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By E. C. Harder

BRITISH Guiana, Great Britain&apos;s only South American colony, may be reached by very comfortable steamers, both from North America and Europe. The trip from North American Atlantic ports requires about 12 to 14 days; that from Europe about 18 to 20 days. A number of steamship lines, including Canadian, American, and Dutch, have regular sailings between North America and British Guiana, with calls en route at various interesting ports in the West Indies and northern South America. Moreover, several lines, including British, German, and French, have steamships operating regularly between Europe and the West Indies. Indeed, so popular have the West Indian voyages become in recent years that, during the winter months, special cruises in considerable number are organized for many vessels that ply in the trans-Atlantic service in the summer. A trip to British Guiana, therefore, has become a delightful experience. After visits at the various attractive Leeward and Windward islands and Trinidad, the approach to the low, flat, British Guiana coast, with its muddy coastal waters extending for many miles offshore, is somewhat of a contrast. Arrival in Guiana waters is signalled by the appearance of the modern high-power Demerara Light, located "on a shoal about twelve miles from the mouth of Demerara river. From this point, if the tide is right, a pilot takes the steamer across the bar, eight to ten miles offshore, and into Georgetown harbour. At high tide, the water above the bar ranges from 15 to 18 feet in depth, depending on whether it is neap tide or spring tide; at low tide, the corresponding depths are 9 to 11 feet. As the bar is of soft mud, however, it is usually possible for vessels to pass over it with a draught of about two feet in excess of that indicated by the tide tables. Upon nearing the shore, one sees first the Georgetown wireless towers, then the light-house and the tall chimneys of sugar mills and of various factories in Georgetown, and finally the palms and other tropical trees and the houses of Georgetown itself along the sea shore and the east bank of Demerara river. Extensive wharves operated by various exporting and importing companies stretch along the river bank and activity prevails in Georgetown harbour. The principal exports are sugar, rice, gold, diamonds, bauxite, balata, lumber, fruit and other tropical products. The imports are food-stuffs, wearing apparel, and manufactured materials of many kinds.

Jan 1, 1936

Jan 1, 1969

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By J. Hindman, E. Moeller

Vermiculite is currently mined from shallow (less than 25 m or 80 ft) surface deposits throughout the world. The largest producers are Palabora Mining of Phalabowra, South Africa (ore stock is a phlogopitemica), Xinjiang Yuli Xinlong Vermiculite of Korla, China, and W.R. Grace of Enoree, SC (ore stock is a biotite mica). Smaller operations are in Australia, Brazil, Russia and Zimbabwe. They also produce vermiculite on a continuous basis but do not export any significant amounts of product to North America. Intermittent and poorly documented production on a minor scale is reported from Argentina, Egypt, India and Uganda. Worldwide vermiculite production in 2004 increased1.7 percent to 432.8 kt (477,000 st). North American production declined, while African and Chinese production continued to increase.

Jan 1, 2005

By Raja V. Ramani, Robert L. Frantz

"The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral Technology Center (GTC) for Respirable Duet within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental understanding of all aspects of respirable duet associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration.The stated objective of the Federal Mine Safety and Health laws is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life with-out incurring any disability from pneumoconiosis or any other occupation-related disease ....""Significant progress has been made in lowering the dust levels in mines since the inception of the Bureau's respirable dust research program. It is generally agreed that mines are less dusty today than they were a decade ago. However, the most serious hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found."

Aug 31, 1989

[A Aall, Christian H., M49 A Dir, Smelt & Ref, Am. Metal Climax, Inc., 1270 Ave. of the Americas, New York 20, N. Y. Aaroe, S. L., A54 A VP, W. S. Tyler Co. of Canada Ltd., P. O. Box 100, St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Prod Frmn, Lepanto Cons. Mining Co., Lepanto, Mt. Province, Philippines Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016 Tiger Lane,-Ipoh Peram, Malaya Abel, John F., Jr., J53 F Mine Engr, Thompson Creek Coal & Coke, Carbondale, Colo. Abell, Leo M., M31 B Const Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, H. E., A57 Mangore Australia Pty. Ltd., 901 Hay St., Perth, W. Aust.,, Australia Abenius, Hakan V., M52 Falun, Sweden]

Jan 1, 1961

On the following pages are abstracts of papers published by the Institute during the year 1935 as TECHNICAL PUBLICATIONS and CONTRIBUTIONS, papers in bound volumes appearing for the first time, and papers in MINING AND METALLURGY. For abstracts of papers that appeared in bound volumes in 1935 but that were published as TECHNICAL PUBLICATIONS in 1934, see the YEAR BOOS dated January, 1935.. Many of the TECHNICAL PUBLICATIONS have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 64. Volume numbers are given as listed at the beginning of the index, page 71. The abstracts are grouped as follows: [Page Metal Mining 17 Uses of Metals 23 Milling and Concentration 23 Iron and Steel Division 26 Nonferrous Metallurgy (Reduction of Ores)...: 34 Institute of Metals Division (Founding and Metallography of Nonferrous Alloys) 36 Page Coal Division 43 Petroleum Division 50 Industrial Minerals Division (Nonmetallics) 57 Mining Geology 60 Mineral Industry Education Division 62 Geophysical Prospecting 62]

Jan 1, 1936

By Sidney V. Gold

Should Gold Producers Hedge Their Positions Through : Sales on Forward Markets? Purchases of Put Options? Sales on Spot Market? Forward Markets Assumptions 1. Producer has a known amount of Gold to sell in year ahead. 2. Effect on price is the same whether sold Forward or Spot Market. 3. None of us have knowledge of Future Price Trend. 4. Contange Market prevails in which Forward price premium is approximately equal to rate of interest.

Jan 1, 1983