Search Documents

Jan 1, 1943

By J. Mitchell Linne

In 1986 at the request of Bureau of Land Management, the U.S. Bureau of Mines studied 23,225 acres of the 27,980-acre Jordan Craters Wilderness Study Area (OR-003-128) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 20 miles northwest from Jordan Valley. No mining activity has been recorded within the study area, and no metallic or industrial mineral resources were identified. Small isolated occurrences of decorative quality stone were identified. However, none of these occurrences constitute a resource. Although the study area is underlain by relatively young volcanic rocks, the area has no known geothermal energy resource.

Jan 1, 1987

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

Jan 1, 1967

By A. Dutta, B. Devulapalli, A. Mukhopadhyay, E. W. Grald

"Computational Fluid Dynamics (CFO) has matured over the past two decades as an analysis tool for conducting virtual experiments with significant time and cost savings. It complements and reduces physical testing. CFO has penetrated the diverse materials industry in much the same way as Computer Aided Design (CAD) did more than a decade ago. As the basic numerical algorithms used in CFO have steadily improved, so have the reliability, consistency and user-friendliness improved significantly, too. Other recent trends have also contributed to the rapid growth and widespread adoption of CFO. In this presentation, CFO applications from several materials processing industries will be presented using case studies. Emphasis will be on metals, glass and semiconductor applications.IntroductionThe term materials processing covers a diverse array of industrial applications and products today. From the continuous casting of steel, to the deposition of semiconductor materials atom by atom, to the extrusion of molten polymers, materials processing applications span an incredible range of length scale, process times, pressures, temperatures and velocities. The properties of the materials themselves, in terms of density, viscosity, thermal conductivity, etc., can be complex functions of temperature, shear rate, chemical composition and time. And the processing equipment may be very complicated in geometric shape.Computational fluid dynamics (CFD), the technique of solving the governing equations of fluid motion and other related phenomena using a computer, has enjoyed widespread and rapid growth, which started in the aerospace and automotive industries. More recently, CFD has also been successfully applied to a great many materials processing problems, in spite of the challenges described in the previous paragraph. The reasons for the growing usage of CFD in materials processing are many. Using CFD to test design options and reduce the number of physical prototypes can decrease the time and cost associated with new product and process development. CFD gives insight and provides detailed predictions of operating conditions in lieu of difficult, intrusive and often expensive experimental methods. CFD can be used as an aid to scale-up processes from lab or pilot scale to full production. Troubleshooting the performance of existing equipment is often carried out with the help of CFD. Determining how an existing piece of process equipment will operate under new conditions, or with new input ,materials, is also a common task for CFD."

Jan 1, 2004

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

By R. Samuels, R. Klimpel

"IntroductionLaboratory and industrial grinding tests have shown that the process of size reduction of metal containing ores can be significantly influenced by chemicals added to the slurry being ground.,The terms grinding aid or grinding additive refer to a substance which, when mixed into the mill contents, causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use.A wide variety of grinding additive mechanisms have been suggested in the general mining literature (1,2,3,4,5,6,7). The prevention of particle agglomeration, slurry cushioning of grinding media impact, grinding media coating, changing the strength of macro porous rocks, and chemical adsorption on flaw surfaces to change bonding forces and surface energy have all been suggested. More recently, some grinding additive work has been carried out (8,9,10,11) which suggests that the use of efficient chemicals to control the fluidity of dense slurries is a viable economic approach to achieve improved grinding rates. These increased grinding rates are achieved with no increase in power to the grinding mills and apparently with no increase in media consumption costs. Unlike much of the previous work with grinding additives, this recent work is accompanied by a rather complete engineering characterization and prediction of performance capability. The chemicals involved were chosen so as to efficiently control the viscosities of slurries under conditions of high shear yet not adversely affecting flotation, flocculation, and other downstream surface chemistry operations."

Jan 1, 1979

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By Raymond B. Ladoo

"Domestic Situation:The greatly increased use of lithopone as a base for paints, particularly for interior use, has timulated the demand for barytes to such a degree that the supply cannot keep pace with the demand. Lithopone is an artificially prepared compound composed of about 70 per cent barium sulphate and 30 per cent zinc sulphide, precipitated together. Its most important use is in paint, but it is also used in oilcloth, linoleum, rubber goods, shade cloth, etc.Prior to the war large quantities of barytes were imported from Germany, but during the war imports were negligible, domestic production increased very greatly and is still increasing. Ground barytes as used in paints/ formerly regarded as an adulterant, but now it is generally recognized as a valuable paint constituent. Mile domestic sources have expanded rapidly they have not overtaken the demand and there is need for still greater expansion. Stocks are low, little is being sold on the open market, and prices are high. Since barytes is a gangue mineral associated with metallic ores now being mined in the west, it is suggested that more attention be given to its recovery as a by-product.The following tables compiled from reports of the U.S. Geological Survey and the Bureau of Foreign and Domestic Commerce, indicate the growth of domestic consumption."

Jan 1, 1920

By C. H. Riggs

THIS REPORT give's the results of a study of the central and south parts of the Cushing oilfield, including a description of the geology, a review of the production history, and estimates of oil reserves available by secondary-recovery methods. Each of the major producing zones of the field is treated separately. The report, which is one of a long series of field studies the Bureau of Mines has conducted over the past 40 years, was prepared to aid operators to increase oil recovery and to help prevent underground waste in the Cushing field, in the State of Oklahoma, and in the United States. The geology and production history are presented not as a review of past behavior of the Cushing field but rather to interpret the possibilities for increased oil recovery by future development of this and similar areas. The field, which is in the northwest corner of Creek County, Okla., was discovered in 1912 and developed during 1913 and 1914. For several years it, was one of the most important areas producing high-grade crude oil in Oklahoma. Although some oil has been recovered from each of 10 separate reservoirs, nearly 98 percent of the total recovery of oil in the area studied was from 4 major producing formations (table 1). Of these, only the Bartlesville [ ]

Jan 1, 1958

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

By D. N. Dietz

Jan 1, 1969

By Chris McKee

Quartz has been of interest in occupational health for years because it can cause silicosis after prolonged exposure. New OSHA regulations (Air Contaminant; Final Rule) list perlite as a nuisance dust. They conclude that perlite is nontoxic when air-borne total particulate concentrations are 15 mg/m3 or below and when quartz content is less than 1% crystalline silica. OSHA has established an 8-hour PEL of 15 mg/m TWA for total perlite dust containing less than 1% quartz. OSHA has established a 5 mg/m3 TWA PEL for respirable perlite. These limits will protect workers from significant risk of eye, skin, or other physical irritation. This regulation is based on a Group 2A classification as a probable carcinogen in humans, at the 0.1% crystalline silica level, by the International Agency for Research on Cancer (IARC 1987a, b). IARC found sufficient evidence for carcinogenicity of crystalline silica in animals and limited evidence in humans. Perlite is not listed as a carcinogen by OSHA or the National Toxicology Program.

Jan 1, 1990

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979

By M Warnken

Major cities are not only the focal point for AustralianÆs work, leisure and homes, they also are the focal point for the flow of resources into the built environment, motor cars and transportation and urban consumables. The steady increases in æstockÆ and waste generation, in line with GDP growth, means that cities will become the mine sites of the future if the inherent value is recovered from these materials at end of life. The urban waste stream can be characterised as containing approximately nine per cent hydrocarbon-based materials; 57 per cent biomass-based material; 28 per cent fully mineralised materials that are inert, five per cent metals and less than one per cent of problematic materials that are potentially hazardous and toxic. In order to convert these wastes into value added inputs into the economy, a number of technological interventions are required. These æurban waste mining techniquesÆ revolve around source separation and material streaming. One issue that needs to be overcome when determining which mining technique to implement, is identifying the option that will deliver optimal value, both from a financial and a sustainability perspective. The difference between embodied energy and calorific value is a case in point. Highest net resource value (HNRV) is a concept that can assist in choosing between different resource recovery options. The assessment can be done at a strategic level, or can be used to work out material specific issues. For example, used tyres can be recovered for their energy content at an approximate cost of $120 per tonne, whereas mechanical processing of used tyres can deliver a net benefit of $192.

Jan 1, 2006

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on site facilities depending on the ore type and the grade. The processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and the complexity of the operation, there are unique challenges in optimizing life of mine production scheduling. This paper describes those challenges and the methodology developed to take advantage of different scheduling software systems that effectively compensate each other and result in reasonable guidance. The paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Feb 27, 2013

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003