Search Documents

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By Paul Sterk

In underground mining a great deal of time, money, effort, and resources have been used in the effort to minimize blast-induced damage. This damage occurs to the back, ribs, and pillars when the energy of the explosive is released back into the rock due to over confinement or the overloading of explosives in the perimeter holes. This damage can result in roof falls, dilution of ore, excessive rock bolting, scaling, screening, shot-creteing and other safety and support issues.

Jan 1, 2003

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By H. Hurkchand

Background: A cross-sectional study was conducted in November2001 to establish the prevalence rates of Human Immunodeficiency Virus (HIV) and sexually transmitted infections (STIs) (Chlamydia trachomatis and Neisseria gonorrhoea) in a coalmining town in Mpumalanga. Methods: 155 adults were recruited (79 males and 76 females), by holding community meetings, and by door-to-door recruitment. Saliva and urine specimens were collected for the analysis of HIV and STI prevalence, respectively. Results: The mean age for males was 31.35 years (min = 19 yrs and max = 50 yrs) and the mean age of the female participants was31.90 years (min = 17 yrs, max = 49 yrs). The prevalence of HIV was found to be 22.78% [95% CI (14.09?33.59)] in the males vs. 47.37%[95% CI (35.79?55.16)] in the females, [p = 0.001, OR = 3.05, 95%CI(1.49?6.26)]. The prevalence of C. trachomatis was 7.90% [95% CI(2.95?16.39)] in the males vs. 12.86% [95% CI (6.05?23.00)] in the females, p = 0.324. The prevalence of N. gonorrhoea was 3.79%[95% CI (0.79?1.08)] in the males vs. 9.86% [95% CI (4.06?19.26)]in the females, p = 0.137. HIV was significantly associated with C. trachomatis, [p = 0.032, OR = 3.18, 95% CI (1.04?9.72)], but was not significant when stratified by gender. HIV was not significantly associated with N. gonorrhoea (p = 0.072) but it was significantly associated when stratified by gender, p = 0.001 for females. There were no significant associations between HIV and age (p = 0.408), even upon stratification by gender. Conclusions: HIV prevalence in this community is high, and corresponds to national figures. However, the prevalence of STIs is surprisingly low as it would be expected to be high in a migrant population. Although communities are exposed to expanding peer-education activities that encourage behaviour change, the prevalence of HIV in this group. There is an urgent need for interventions designed to treat or prevent HIV infection in women generally and in women at high risk. Keywords: HIV prevalence, STI prevalence, antenatal, mining

Jan 1, 2005

By F Linares, B De Waele, K Bischoff, M Lacorde, G Loveday

Recent exploration has identified the presence of detrital iron deposits (DIDs) associated with banded iron formation (BIF) units in the north-west of the Congo Craton, Gabon. The regional geology comprises a complex of granitoids and gneisses assigned to the Archaean Chaillu Complex, within which older slivers of lower amphibolite-grade greenstones are preserved including muscovite-biotite-garnet-bearing felsic schist, amphibolite and BIF. These units are typically overlain by several metres of residuum comprising colluvium, eluvium and duricrust. The residuum is overlain by a regionally extensive loess cover from 2 m to 10 m thick.The DIDs occur within the weathered residuum as mostly unconsolidated gravels with lesser canga (CAN) duricrust draped over deeply weathered hematite. Head grades are in the range of 45 to 52 per cent Fe. Fresh BIF, located from 30 to 50 m below surface, is comprised of magnetite-quartz±amphibole. The detrital iron gravels are comprised of rod- and plate-shaped clasts of hematite (martite)-maghemite-goethite composition, in a ferruginous sand to clay-sized matrix. The DID form ridges and plateaus that coincide with magnetic highs defined using high-resolution ground magnetic surveys.The field relations and petrography indicate that the detrital iron accumulations are the result of weathering (including enrichment) and erosion of primary BIF. This includes removal of quartz, further oxidation and re-cementation of BIF to form ferruginous caprock. This cap and the in situ oxidised BIF were subsequently disaggregated and liberated, and further weathered to form the detrital iron accumulations.Metallurgical test work on bulk detrital iron samples has shown this material can be upgraded to lump and fines iron ore products with grades of 62 to 65 per cent Fe using simple scrubbing and wet screening, followed by dense media separation of the -1 mm fraction, with overall mass yields from 75 to 85 per cent. The test work indicates a high ratio of lump to fines products, sometimes exceeding 50:50.CITATION:De Waele, B, Lacorde, M, Bischoff, K, Loveday, G and Linares, F, 2017. Geological and metallurgical characteristics of banded iron formation associated detrital iron mineralisation in Central West Africa, in Proceedings Iron Ore 2017, pp 259–268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. M. Richards

For most of the 20th century optical petrography has been the primary petrological and mineralogical tool used to characterize coal. The development of quantitative SEM-based techniques, e.g. QEMSCAN®, for coal began only about a decade ago. The application of these techniques for coal lagged behind other commodities, but they are currently being developed with the aim to provide ?one complete analysis? for coal. Quantitative SEM-based techniques are supplemented by quantitative X-ray diffraction (XRD). Recent indications are that these more modern techniques cannot replace the ?standard? petrographic and chemical evaluations, but rather complement them where and when required. The great advantage of quantitative SEM-based techniques is that they are very rapid, with the result that large volumes of samples can be processed on a routine basis. This is ideal for coal type identification, since the results can be used in the creation of ?intelligent? composites. This can lead to the more speedy evaluation of coal deposits by reducing the number of samples on which detailed metallurgical and characterization test work is required, without an increase in the overall statistical error of the resource model. Coal petrography, however, remains important for the prediction of the coking characteristics of certain coals and coal products. As a consequence it is therefore important that any coal laboratory be able to produce data with confidence. This requires strict quality control and assurance protocols that adhere to international standards. Keywords coal petrography, coking strength, scanning electron microscopy, QEMSCAN®.

Nov 1, 2013

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

JAMES DOUGLAS Dr. James Douglas, twice President of the American Institute of Mining Engineers, and one of its principal benefactors, died in New York on June 25, 1918, at the age of 81 years. After a life of extraordinary activity, failure of his health compelled him to retire about 2 or 3 years ago, and in view of his advanced years his death was not unexpected. His funeral was held at the Church of the Mediator, on June 26, and was attended by representatives of the American Institute of Mining Engineers and of the Canadian Mining Institute. His body was then taken to Quebec for burial in the family plot. An extended notice of Dr. Douglas, prepared by Dr. R. W. Raymond, will be presented in the September issue of the Bulletin. LEWIS NEWTON BAILEY Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., April 30, 1918, at. the age of 34 years. He was Master Engineer, .Senior Grade, in the Fourth Regiment, U. S. Engineers; and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character.

Jan 8, 1918

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

Study on Selective Reduction and Magnetic Separation of Low-Grade Nickel Laterite Ore to Produce High Nickel Concentrate

Sep 13, 2010

By W. F. Scott, K. L. Somerville

"This paper outlines the development and inplementation of functional training at the Thompson Mine of Inco Metals Company, Manitoba Division. This training is an extension of similar methods implemented throughout the company to meet safety and health and productivity objectives. It consists of the orientation to the mine, induction in the basic mining skills, and specific training in drilling and other skills in the mine. Initial results indicated a positive effect on the safety performance and proficiency of the mine workforce.IntroductionThe primary mining method at the Thompson Mine is mechanized cut and fill, with secondary recovery of pillars by undercut and fill . These methods require a workforce of about 900 hourly operating employees to obtain capacity production of 6500 tons of ore per day.Historically, turnover of mine employees has been high and large numbers of new recruits are introduced to the mine every year. These men are recruited primarily in Manitoba, but also from distant areas of Canada; most of the se people have no previous mining experience.Training has always been an important component of mine operations. Mine supervisors and experienced miners have committed an appreciable amount of time and effort to training these new recruits. As well, training efforts have been directed toward upgrading the skills of experienced workers.Recently, a growing awareness of the significance of this training effort and its impact on accident frequency, productivity, turnover and other important parameters of the mine operation has led to a review of training methods. The training program described in this paper has resulted from this review."

Jan 1, 1981

Electronic noses are being used in the processing industries and in fields such as environmental and occupational hygiene to detect a wide variety of problems from contaminated foods to toxic chemicals in soils. Recently, research has been conducted into the use of these devices for detecting spontaneous combustion in mines with the aim of producing a method for early detection of a developing heating. Gas samples were collected from both SimtarsÆ 16 m3 large-scale spontaneous combustion reactor and the University of QueenslandÆs two-metre column. The samples were analysed using an electronic nose. GCMS and HPLC were used to identify some of the components present. A number of issues both from a practical mine situation and a scientific standpoint have been identified that need to be addressed before these devices can be used to detect a developing heating. Aluminised bags routinely used in the mining industry to collect gas samples for analysis of the permanent gases are not suitable for use with electronic nose devices as they have a æfingerprintÆ from the polymer lining that interferes with the coal heating fingerprint. Tedlar bags used for environmental gas sampling are also unsuitable due to their fingerprint. Gas samples can be collected in glass gas bulbs with aluminium seals and successfully analysed. However the aluminium foil used to seal the bulbs is a restricted item in underground mines. It was also found that the volatile organic fingerprint of the coal heating was extremely weak at temperatures below 130¦C. Before a useful application can be developed, further investigation into the chemical species present in the off-gases from Australian coals is required.

Jan 1, 2005

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By W. K. Connor, O&apos

The Bureau of Mines is investigating the Co and Mn resource of the West-Central Arkansas District, including field investigations, mineralogical characterization, beneficiation, and hydrometallurgical tests. The deposits occur within the Ouachita Mountains and are con-trolled structurally, occurring along the axes of anticlines making up the mountain ridges. Brecciated novaculite is cemented with a mixture of Mn oxides, primarily cryptomelane and psilome-lane. Cobalt is concentrated within a particular Mn oxide phase, lithiophorite. Chemical analyses on head samples reported up to 25 pct Mn and 0.17 pct Co. Magnetic separation yielded products with up to 41 pct Mn and 0.22 pct Co at recoveries of 95 pct Mn and 93 pct Co.

Jan 1, 1991

By I Sherrell, R Jain, P Jansson

With the depleting iron reserves and difficult market conditions, precision in separation efficiency is of utmost importance. Classical local control options are predominant in the industry, but their inability to adjust to resolve application problems of interest has furthered the need of developing and implementing continuous control methodologies.This paper highlights the recent development in control of Outotec SLon® vertically pulsating high gradient magnetic separator (VPHGMS) including programmable logic controllers (PLC) coupled with distributed control system (DCS), on-site human–machine interface (HMI) control panel, advanced process control, continuous online sampling using Courier® 8 and additional modernisation packages including level control and cooling monitoring. These modern control options result in improved efficiencies, promote safer operation and at the same time reduce operational manpower needs.CITATION:Jain, R, Sherrell, I and Jansson, P, 2017. Automation for efficient separation with the Outotec SLon® vertically pulsating high gradient magnetic separator, in Proceedings Iron Ore 2017, pp 211–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P. J. Gron

"The Samatosum Project is a base and precious metal deposit located in south central British Columbia. A dilute ore reserve of 766, 682 tonnes grading an average 1.1% copper, 3.0% zinc, 1.4% lead, 833 gram per tonne silver and 1.6 gram per tonne gold is available. The base metals occur as tetrahedrite, chalcopyrite, sphalerite and galena. Virtually all of the silver and gold are associated with the tetrahedrite.The mill is operated at a rate of 21 tonnes per hour. Sulphur dioxide is used as a zinc depressant in the grinding circuit. Production of a Cu/Pb/Ag concentrate is accomplished by conventional flotation. This concentrate is then separated into Cu-Ag and Pb concentrates through a reverse flotation circuit utilizing sulphur dioxide, starch and sulphuric acid as lead depressants.The tailings from the Cu/Pb/Ag circuit are treated with copper sulphate to activate the zinc. Production of a zinc concentrate is accomplished by conventional flotation. Dewatering of the concentrates to 6% moisture is done with a LAROX filter press.Tailings effluent is treated with lime and sodium sulphide to precipitate out the heavy metals. The resulting sludge is treated in OYNASAND sand filtration units to produce a quality effluent."

Jan 1, 1990

Jan 1, 1967

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967