Search Documents

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By A. Luszczkiewicz

An innovative hybrid technology for beneficiation of difficult-to-process sedimentary copper ores comprising acidic leaching stage of the feed combined with subsequent flotation has been presented. Acidic leaching, preceding the flotation process, plays a beneficial role of efficient chemical grinding for liberation of copper sulphide minerals finely disseminated in the copper-bearing carbonate-shale rocks. The process was applied on a fully industrial scale. Flotation results were analysed for both chemically modified and unmodified flotation feeds. After several months of industrial scale operation, it was found that both metals recovery and concentrate grade remarkably increased as a result of application of chemical modification of the flotation feed. Beneficial effects of chemical pre-treatment of flotation middlings on selectivity at a comparable concentrate yield in industrial flotation scale, revealed a considerable increase of the total copper recovery by 3.5percent. Based on the industrial and laboratory investigations we consider a further development of the process and introduction of hydrometallurgy for better recovering of metals from low-grade copper concentrates

Sep 1, 2012

By J. M. Kurtz

Ten Methane Monitoring Systems and Machine Control Circuits were examined and tested per the requirements in CFR Title 30, Parts 18 and 27, the Standard UL 913 and the document "Test Requirements For Instruments or Apparatus to be Considered for M.E.S.A. Intrinsically Safe Certification (Tentative)". The test results indicate that none of the products complied with all parts of all requirements as interpreted by Underwriters Laboratories Inc.

Jan 1, 1980

By A Parbhakar-Fox, B G. Lottermoser

Management of solid mine wastes, particularly waste rock, requires careful planning to reduce the likelihood of sulfide oxidation, and generation of acid rock drainage (ARD). Waste management strategies must focus on obtaining a thorough understanding of the environmental characteristics of future waste rock materials. In this study, a waste management strategy for characterising underground waste rock was developed at a polymetallic underground mine in western Tasmania to determine which materials were appropriate for surficial placement. The criteria for surficial placement set by the regulator were that materials had to be non-acid forming and non-metalliferous. A range of cost-effective field-based tools, mineralogical assessments and mineral chemistry techniques were used on a suite of representative drill core material to determine an appropriate waste management strategy. Ultimately, a modified geochemistry–mineralogy–texture–geometallurgy (GMTG) approach was designed, whereby geoenvironmental focused logging and simple prescreening tools such as paste pH and sulfur analyses were used at stage-one; routine acid base accounting and leachate tests at stage-two; and validation tools including X-ray diffractometry and laser ablation inductively coupled plasma-mass spectrometry (ICPMS) at stage-three. This approach should be considered for other mine sites at early and operational life-of-mine stages with similar deposit characteristics, to ensure correct screening and placement of potentially hazardous waste materials in suitable above-ground waste repositories or mined-out mine sections.CITATION:Parbhakar-Fox, A and Lottermoser, B G, 2017. Effectively linking mining geology with waste management – a case study from western Tasmania, in Proceedings Tenth International Mining Geology Conference 2017, pp 117–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By Irvin G. Burough

ANDROS INCORPORATED has designed, manufactured and delivered four handheld C02 DETECTORS and three handheld CH4 DETECTORS. These instruments are for in-mine safety use. The DETECTORS incorporated an NDIR optical/electronic analyzer design in which exceptional zero stability is achieved by pressure modulation of the sample gas. This eliminates the need for daily calibration. This stability and the miniature design (2.5" x 4.5" x 4.5"; 4.5 lbs) of the C02/CH4 DETECTORS provide practical instruments suitable for routine safety inspections. This report includes the theory and design of the instruments as well as studies of gas-pressure modulation by a piezoceramic-driven Helmholtz resonator.

Jan 1, 1979

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 22, 2007 at the Charles F. Barber Pavilion (Museum Convention Center) in Leadville, CO. The four inductees are James Harold Courtright (1908-1986), Dr. Howard L. Hartman (1924-2002), Charles Washington Merrill (1869-1956) and Kenyon E. Richard (1915-1993). The inductions will bring to 197 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2007

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By D. Linzey

"History of Whitehorse Copper BeltThe first discovery of copper on the Whitehorse Copper Belt is reported to have been made by miners on their way to the Klondike in 1897. By 1899 the district had been well prospected and many of the presently known deposits had been staked.The first shipment of ore was from the Copper King property in 1900. This consisted of 9 tons of hand picked ore grading 46.4% copper. It was not until the period between 1912 and 1917, the production years of the Pueblo Mine, that significant ore shipments were made. Total production was 140,000 tons at 3.5% copper. An underground disaster killed six men and closed the mine in March 1917.Although the general area was dormant until after World War II, by 1947 geological mapping, magnetic surveys and diamond drilling had been done on the important showings. In 1954 Mr. Aubrey Simmonds directed the formation of Imperial Mines and Metals, which acquired by option and staking a large part of the Whitehorse Copper Belt. In 1957 Mr. Arnold Pitt reorganized the company as New Imperial Mines. With financing from Sumitomo and Toronto-Dominion Bank, a mill was built and production was started from the Little chief orebody by open pit in 1967."

Jan 1, 1977

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By Charles H. Bucknam

A gold sampling optimization study was carried out in support of open pit gold mining operations for the Newmont Gold Company Bootstrap-Capstone deposits in Northeastern Nevada. Six bulk samples were tested using fire refining techniques at field particle size, to determine coarse particle heterogeneity of the ores, and by gravity .concentration methods at 10 mesh particle size, to observe any particulate gold liberation. An overall sampling model is presented for the deposit based on the pooled test information, to reconcile the results of coarse particle heterogeneity testing and the fine particle 'liberation testing. The sampling model is used to recommend procedures to control the variability of gold grade estimation due to the fundamental error (nugget effect) during sampling, sample preparation and assaying of the ores and other fundamental variances. The technique of simplified quantitative risk analysis (SQRA) is used to provide an economic justification for implementation of. recommended improvements to field sampling practices.

Jan 1, 1999

By R. R. Brandenthaler

The development of the Seminole area into one of the major oil-producing sections of the country has been accompanied by many innovations and departures from former methods of development. On July 1, 1929, two years and nine months from the date of discovery, 20,490 acres were considered proved, and additional acreage is constantly being developed. Because of its peculiar conditions, extent, and rapid rate of development, the Seminole area provided numerous problems, the solution of which necessitated research in connection with practical field operation; as a result, there was a radical departure from methods usually employed in the development of a new field in the Mid-Continent area.

Jan 1, 1930

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Valuable base metals, such as nickel, cobalt, molybdenum, vanadium and tungsten, are used in a wide range of important technological applications. The demand for many of these metals has increased significantly over the last few decades, driven especially by economic expansion in Asia generally and China in particular. This has led in turn to a large growth in the output of mines in order to satisfy this increasing demand, as shown by the data in Table 1 (USGS, 1994, 2014). These data reflect an even longer trend of growth of these metals, with nickel, for example, showing an average rate of 5.3% per year from 1980 until 2015 (International Nickel Study Group, 2017). This rapid and sustained rate of growth means that annual mine outputs for nickel, tungsten, molybdenum and vanadium have had to double roughly every 11 to 14 years, whilst cobalt mine output has had to double roughly every 7 years, over the period from 1994 until 2014. With the average working life of a nickel mine being between 17 and 22 years (Statista, 2017), this means that from the time a nickel mine opens until it closes, the industry needs to find the equivalent of another three or four mines of a similar output to satisfy this relentless growth in demand for the metal."

Jan 1, 2017