Search Documents

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

By J. T. Furey

"A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from a gold/tellurides bearing sulphide ore, and to compare the performance of column flotation to conventional ""mechanically agitated"" flotation.Tests were conducted in a 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail.The ore had an average ""as tested"" feed grade of about 5 g/t gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbragite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of 97%, but produced grades of+ 150 g/t Au. INTRODUCTIONColumn flotation is the most significant innovation that has occurred in the mineral processing industry in recent years and has become an important alternative to mechanical flotation. Column flotation has been most widely accepted and applied in cleaning service where it has frequently proven to be superior to mechanically agitated flotation. Roughing in columns has not been ignored, but early testing indicated that columns may not be capable of achieving adequate recovery and, to date, columns have not been seen as serious competitors for mechanical roughers."

Jan 1, 1990

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By Vinit Mody

The belt conveyor is one of the major pieces of equipment for transferring bulk material in mining operations. However, considerable amount of respirable dust may be generated whenever the bulk material is loaded, dumped, or transferred. This report identifies and evaluates various dust control technolgies applicable to belt conveyors, and describes how an integrated systems approach can reduce dust emissions at a transfer point. Phase I of the program consisted of literature search and a critical evaluation of various dust control technologies. The work established that a comprehensive approach to calculating exhaust volumes for dust collection system does not exist. The parameters that affect the wet dust suppression efficiency were also reviewed. Based on the Phase I work, bulk material handling system and dry dust collection or wet dust suppression systems were designed and installed at a number of transfer points in a limestone processing facility, a surface mine selected as a field test site. Field test data were used to determine the validity of various exhaust volume calculations at the different transfer points. The field test data also formed the basis for the evaluations of the relative effectiveness of commercially available and wet dust suppression systems in controlling respirable dust emissions.

Jan 1, 1984

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yuji Wada, Yukio Katoh, Yoshikazu Hirosaki

In our previous work, the results of photographic observation using a high speed framing camera showed that the difference between precursor air shock wave velocity and detonation velocity was primary factor for the channel effect. It is assumed that the decreasing precursor air shock wave velocity can prevent the channel effect in charge hole.

Jan 1, 1996

By J. A. Cooper

The objectives of this research were to define the chemical composition and physical characteristics of the aerosols associated with attached radon daughters in operating uranium mines, and to investigate the relationship between these aerosol parameters and operating conditions. Major Results and Conclusions The organic, inorganic and radiological characteristics of test chamber and active U-mine aerosols have been measured as a function of particle size. These measurements represent the first detailed analyses of the organic and inorganic components in U-mine aerosols and the first determinations of the details of the individual and total radon daughter distributions in operating U-mines. The following is a list of the major results and conclusions:

Jan 1, 2012

By Kenneth R. Sites

Under this program two tape recording and triggering systems were developed and delivered for use in the Bureau of Mines microseismic program. The systems are designed to improve the effectiveness of the Bureau owned Sangamo 3500 series and SABRE VI instrumentation tape recorders. The system is designed to capture random microseismic data, digitize and temporarily store these data, start the tape recorder; and then transfer the data to magnetic tape for permanent storage. The system is designed to pack data on tape such that the tape may be simply played back through galvo drivers onto an oscillograph such that a continuous series of analog records, with corresponding time of day information, are reproduced without excessive oscillograph paper waste or the need for the operator to search for valid events.

Jan 1, 1980

By R Riquelme

The El Salvador porphyry Cu deposit (26¦ 15Æ Lat S, ~2700 masl) and associated exotic mineralisation is situated at the back-scarp of the late middle Miocene Atacama pediplain in the western Precordillera. New, together with published 40Ar-39Ar data from El Salvador combined with morphologic analysis reveal that the palaeospring plumbing system related to exotic mineralisation at the Damiana exotic Cu deposit and the local geomorphology has not changed fundamentally between the late Eocene and late Miocene. Stable H/D isotope data on supergene alunite from El Salvador indicate an overall increase in dD values (VSMOW) from -74ë at 35.82 ¦ 0.95 Ma to -23ë at ~11 Ma. The transition from strongly to moderately negative deuterium values occurred between ~16 and ~13.5 Ma. Supergene alunite from the El Hueso (3950 masl) sedimentary rock-hosted epithermal deposit ca 35 km SE from El Salvador was dated at 8.19 ¦ 0.01 Ma and yielded a dD value of -25ë. We interpret the increasing deuterium excess as the result of strong evaporation and recycling of meteoric water after ~15 Ma and as indicative for a change in precipitation patterns and climate desiccation. In contrast, the strongly negative dD value for late Eocene supergene alunite points to a more humid climate and an elevation similar to the present. The late Miocene supergene activity at El Hueso is probably related to an uplift of the Precordillera to elevations sufficient for capture of orographically controlled precipitation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

The Ngakuru zeolites are located about 20 km south of Rotorua and comprise a number of deposits dispersed along several fault lines. Relatively recent volcanic activity (250,000 years ago) resulted in ash depositions that vary in depth and mineralogy. Subsequent variable thermal alteration intensities generated predominantly clinoptilolite and mordenite zeolites with a range of physical characteristics. Typically the zeolites have low density (650 kg/m3), have high liquid (60% of dry weight) and odour absorption characteristics, and a high affinity for soluble cations (CEC =: 100 meq/100 g). Traditional kitty litter and oil absorbency markets are being expanded. New opportunities in waste and potable water treatment, organic and synthetic slow release fertilisers, use as a light weight aggregate for speciality concretes, and pozzalome activity are currently being researched.

Jan 1, 2000

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By Randall J. Essex

The Construction Institute of the American Society of Civil Engineers recently published the second edition of a 1997 publication on geotechnical baseline reports. The new publication, called Geotechnical Baseline Reports for Construction, Suggested Guidelines, represents a 2-year effort that adds three new chapters to the original publication, as well as capturing practitioner commentary through two industry workshop sessions. The paper will overview the contents of the new publication, particularly the three new chapters.

Jan 1, 2008

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

The extent to which man's activities are influencing the earth's climate is subject to considerable debate. Internationally however, this debate has been put aside somewhat by the Kyoto Protocol. This international agreement is the political response to the threat of Global warming, predicated on the precautionary principle.NZ is seeking to be a leader in the Kyoto Protocol. Given our unique GHG emission profile and the structure of our economy, and the major uncertainties in both the science of climate change and the Kyoto Protocol itself, this desire to lead is absolutely inappropriate in this instance. We face a different, and often more severe, set of challenges in an economy that prices C emissions than virtually all of our trading partners. Unfortunately, these differences have not been reflected in climate change policy development to date. This represents a major threat to New Zealand's economy, wealth and jobs, particularly in the sectors that have been the core drivers of our economy over the last 20 years or so - agriculture, energy, primary processing. We do not, and should not, seek to avoid the issue but we must protect our economy and move with or follow our trading partners and competitors, not lead them.

Jan 1, 2002

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957