Search Documents

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

By J M. Galvin, B J. McKinnon

Lightning Ridge, Australia, is the largest opal producing area in the world. Most opal is mined from shallow underground mines by individuals or small partnerships with the industry having been protected from large-scale development to date. The safety performance of opal mining has lagged both general mining industry standards and community expectations. The application of geotechnical analysis to the opal fields has the potential to considerably reduce injuries and fatalities. With consideration of the local culture, preliminary geotechnical analysis has been applied to some current methods of work utilised at Lightning Ridge. Practical solutions have been advocated and are presented in this paper. Improvements to safety generated by these practical solutions indicate that further geotechnical research at Lightning Ridge is warranted and would be beneficial.

Jan 1, 2002

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

Fully mechanized longwall mining with large mining heights (LMHs) in shallow-depth thick coal seams has been widely applied in Shenfu coalfield, China. Dynamic loading and rib spalling is serious when the LMH working face experiences periodic weighting in shallow coal seams. The advanced breaking position (fracturing ahead of the face) in the roof affects the strength of the mine pressure (weighting) when the roof is broken. Based on the theory of the “elastic foundation beam,” this paper presents a mechanical model for the advanced breaking of the roof, including a predictive formula. In an attempt to verify the formula, a field program consisting of multiple-point borehole extensometers installed in the roof in advance of the longwall face was performed in the No. 22201 working face of Zhangjiamao coal mine in the Shenfu mining area, China. The field measurement results show that the roof movement of the LMH working face is detected prior to roof pressure increase, and that the roof breaks approximately 5–8 m ahead of the face. This compares with a calculated value of 6.9 m, indicating that the formula developed in this research is reliable and should have application in predicting roof pressure associated with LMH working faces in shallow coal seams.

Jul 28, 2020

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

On the recent trip from Vancouver to Calgary with the President, Mr. C. C. Huston, and yourself, I had the opportunity of outlining a plan based on the following: Among the aims of the Institute are, obviously, the fostering of the confraternity of those engaged in the technical and management fields of the mining and petroleum industries. This may be achieved in a number of ways, of which, to me, the interchange of ideas and experience between different parts of Canada and different sections and divisions of the Institute appears to be one of the most important. I think you and the membership as a whole are, and have been, well aware of this. The annual tour of the President .and Secretary, particularly their visits to Branches, shows this to be true. The interchange of ideas through the medium of the BULLETIN also illustrates the point; indeed, most Institute activities are directed along these lines. I am convinced that much more could be accomplished if it became financially possible to do so. Many able and fine men are, I think, willing and anxious to give their time and energy to furthering these phases of Institute activity, but it is unfair to expect them to assume as well the financial obligations involved. Specifically, I would suggest that the following could be done if sufficient funds were available:

Jan 1, 1952

By Mark Svinkin

The purpose of this paper is to present an overview of recommended existing criteria of ground vibrations generated by blasting. It is shown that these criteria have limited liability because they were found for specific categories of structures. A new approach based on measurement of structure vibrations is suggested for assessment of damage in structures subjected to blasting vibrations. This approach provides the flexibility of implicitly considering a variety of soil-structure interaction and structure conditions. It is explained a new frequency-independent safe-level criterion of 51 mm/s (2 in/s) for the PPV of structural vibrations. Attention is brought to use seismographs properly calibrated for the required frequency range. Positive flexibility is demonstrated in assessment of structure and component of concern vibrations from blasting.

Jan 1, 2003