Search Documents

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

Wastewaters from Mining Projects both gold mining and coal mining generally have minerals in solution or very fine material which does not settle out quickly. These waters in the past have been discharged into the nearest water course and caused extensive pollution.

Jan 1, 1986

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Nines investigation of the more economic utilization of the so-called "black oils" of Wyoming,. This problem is being studied by the Bureau of Nines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station, Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oilshas been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), end the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black oil, it was thought t that a more fundamental attack would assist materially in the problem of sulfur removal.]

Jan 1, 1941

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

By L. B. Phelps

Many coal mining companies have potential surface mine reserves which either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1985

By N. McEwan

Keywords: refractories, chromite, Marico This paper examines the role of refractory-grade chromite in refractories. The chromite deposit at Verref?s Marico Chrome mine is described. The refractory properties of chromite and their role in basic refractories are described. The properties and metallurgical applications of chrome-containing refractories are described and finally environmental issues associated with chrome-containing refractories are discussed.

Jan 1, 2011

By S. M. Rupprecht

Transportation accounts for some 26% of all mine accidents in South Africa. Although this figure may not be as prolific as fall of grounds accidents or accidents caused by seismic events, the enormity of transportation accidents demands attention, especially as many of these accidents are avoidable. This paper investigates vertical (i.e. shaft), horizontal (i.e. haulages), and in-stope transportation systems and their function as it applies to safety. Recent transportation accidents are discussed looking at current trends within the three transportation areas. In the shaft area, discussions will focus on handling of material cars, loading and off-loading of the workforce and management of shaft orepass systems. The horizontal component will focus on personnel transportation, safety around trains and hoppers, and handling of material in the cross-cut. The discussion on in-stope transportation will focus on the general congestion of the stope environment and how it affects the overall movement of personnel, material, and rock. Of concern are the large numbers of material handling and scraper winch accidents that occur and which will be discussed in some detail. The paper will conclude with a section on proposed guidelines within the three above-mentioned systems for mine engineers to consider in mine design and life of mine planning and scheduling. Keywords Underground logistics, safety in material handling.

Jan 1, 2011

By G. I. Mathieu, R. W. Bruce

Flotation schemes for the separation of molybdenite from other minerals are based on utilizing the Inherent hydrophobicity of molygdenite (Fuerstenau1). This natural floatability was attributed to the crystalline structure of molybdenite by Gaudin et al.2 who suggested that any surface formed by the rupture of van der Wall's bonds should be hydrophobic and, therefore, naturally floatable. Other authors argued that "natural floatability" is dependent of adsorption of hydrocarbon ions and/or molecu1es on the surface of the minerals. This theory, albeit-c questioned 1,2 has long been recognized in actual practice of molybdenite flotation as the latter in carried out with hydrocarbons, such as fuel oil, kerosene and stove oil. Although conferring ready floatability to molybdenite, these presents generally have little effect on other sulphides and silicates. However, talc is a noteworthy exception because of its innate floatability4. Not withstanding the reason for this behavior which has also been attributed to crystal structure2 its end results as in the case of molybdenite is an immediate flotation response to frothing oils arid kerosene, as was observed by Baranovski5, Sutherland and Wark6.

Jan 1, 1974

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978