Search Documents

By L. D. Tracy

Many bituminous coal-mining companies have inaugurated extensive safety programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania. Story of the Explosion At about 10 o'clock on the night of the explosion an examination was made in No. 2 butt left and parallel off No. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of No. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 13 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air as explosion occurred.

Jan 1, 1927

By H. L. Martin

A joint federal-provincial approach in gathering basic information from industry on mine production, concentrator operations and ore reserves, initiated during 1978, is a major step toward the goal of achieving better government-industry communication through a common data base. Information from questionnaires sent out by provincial governments is shared with the federal government; correct interpretation is ensured by mine visits conducted jointly by provincial and federal representatives. Initial focus is on nonferrous metal mines. The federal Department of Energy, Mines and Resources (EMR) is responsible for a national analysis that is aimed at the early detection of worrisome developments-and their reasons-in the flow from resources to reserves and from reserves to supply of these metals. The heart of the national analysis is the annual construction of a "monitoring curve", showing each metal's aggregated mine production as it would decrease over time if no new reserves and production capacity were to be added from the year of analysis. For a given metal, a comparison of monitoring curves from year to year can reveal early signs of supply stagnation. In anyone year, a monitoring curve in conjunction with foreseen needs for Canadian mine output will show the production gap that would have to be filled from reserves and production capacity yet to be developed. The production gaps for copper, nickel, zinc and lead, the four leading base metals mined in Canada, are shown for the 20-year period ahead, in the context of production achieved during the past 20 years. It is shown that reserve levels commensurate with likely future production levels would require that average annual reserve additions during 1978-98 exceed the average annual additions during the preceding 20 years. Reserve levels of all four metals have declined in recent years. A review of significant discoveries in the last five years suggests that this fall in reserves is not the result of a lack of exploration successes, but of stagnation in development for various economic reasons.

Jan 1, 1979

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By Jhon Melo

Los “softwares de aplicación” como herramientas en la exploración geológica, generan importante información geográfica sobre el área a estudiar, así como la cartografía y la toma de muestras en laboratorio. En ese sentido, el presente texto señala el manejo adecuado de dichas herramientas a través del uso de una base de datos, donde existe una estructura basada en el software (VISUAL FOXPRO, PARADOX, etc) y asi ejecutarla mediante una aplicación gráfica que permita tener una representación de lo estudiado como ocurre en un muestreo geoquímico.

May 25, 1998

By M S. Powell

In this paper it is argued that we are entering a new mining era, based on considerably more challenging orebodies as we rapidly expand minerals production by exploiting previously uneconomic deposits. Rapidly increasing production costs cannot be sustained by continually increasing commodity prices, as illustrated by the recent downturn in the industry.Driven by reduction in grade, requiring the processing of 50 to 100 per cent more ore to recover the same amount of metal, often accompanied by finer grain structure - necessitating a finer product size and more challenging recovery - the productivity of the mining industry is dropping in real terms. The author suggests that tweaking current technologies and relying on economies of scale will not turn the industry around, but rather a switch to considerably more efficient processing is required.It is imperative to utilise the properties of the orebody, especially in terms of variability, in revolutionising our processing techniques. Our new mantra may be æselective mass mining with flexible processingÆ. This paper explores how this may be implemented using current technology and equipment in order to change the cost profile of the new mining industry. Orebody knowledge, based on the underlying process drivers, rather than proxies, is required. These properties and their variability will need to be propagated into the orebody through utilising the geological data rather than smoothing block averages, which destroys information on variability.Novel flexible circuit designs are presented that can respond to a wide variability in ore properties and throughput requirements in order to slash processing costs and energy utilisation, while enhancing overall recovery. The success of these circuits will be based on an ability to predict at both design stage and in everyday processing the variable ore properties, which is dependent upon reliable orebody knowledge that caries variability and underlying processing properties.CITATION:Powell, M S, 2013. Utilising orebody knowledge to improve comminution circuit design and energy utilisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 27-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By Kasimcan Koruk, Julian M. Ortiz

A geological model accounting for uncertainties possesses important advantages for resource estimation. Machine learning algorithms (MLAs) employed on multivariate geochemical datasets open up ways to new methodologies for such geological models with ease in comparison to traditional geostatistical methods. This article proposes a two-step MLA with an ensemble implementation to define geological domains and their uncertainties based on geochemical data. The proposed workflow is applied hierarchically on a dataset from a porphyry copper deposit to perform binary classification that can be attributed to alteration domains.

Mar 1, 2024

By Eugene A. Stephenson

THE year 1935 is noteworthy for the superior legislative measures passed by several states. Sincere efforts have been made to establish equity between the various producing tracts in oil and gas fields. Outstanding legislative measures include the New Mexico law, known as Senate Bill No. 79, approved on Feb. 23; the Oklahoma law on April 22; the Texas law on April 30; and the Kansas law, which became effective July 1. Primarily designed to prevent waste, but more or less the direct out- growth of the current excess of potential oil and gas production, these statutes fall in the class of "Proration Laws."

Jan 1, 1935

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By S. G. Britton

"Strategies to improve performance in mining production, maintenance and mineral processing operations have evolved over time from straightforward time studies of individual machine performance in the 1960s-1970s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980s-1990s. These newer strategies fall under the broad descriptive category of operational excellence.Operational excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining include the following:• Six sigma for addressing errors within mining or milling process and work standards.• Lean manufacturing to optimize organizational and operational performance through continuous improvement.There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts.The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to make the change versus the estimated value gained. The practice is identified as the value mapping process.This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement."

Nov 1, 2016

By D. M. Ziebarth

"During the mid to late 1960s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace, supporting a large part of the world demand, until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corp. of Saskatchewan (PCS) was one of the major producers planning upgrades to its production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1.5-kt/h (1,650-stph) hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market.BackgroundPotash production is a major Saskatchewan industry and has played a significant role in the economy for more than 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) Mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in 12 companies opening 10 mines by 1970. In 1975, Potash Corp. of Saskatchewan was created by the government of Saskatchewan, and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine, near Saskatoon.Cory has been in operation since 1968 and is located 12 km (7.5 miles) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3,300 ft) below surface.PCS has embarked on sizable capital expansions of more than CDN$7 billion.The $1.6-billion Cory expansion was expected to raise operational capability of the site to 2.7 Mt/a (3 million stpy), an increase of 1.9 Mt/a (2.1 million stpy). To achieve 2.7 Mt/a (3 million stpy) of finished product and considering the 22.6 percent average production recovery (Potash Corp, 2013), 12 Mt/a (13.2 million stpy) of ore must be hoisted to the surface for processing. To deliver this rate required upgrading of the hoisting plant to 1.5 kt/h (1,650 stph). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly that the work was completed safely (Potash Corp., 2013)."

Apr 1, 2017

By Henry Kreisinger

Some of the investigations conducted by the Bureau of Mines have for their object the collecting and disseminating of information regarding methods by which the fuels of the country may be most efficiently used. As the analysis of flue gases tends to develop better methods of firing, which in turn reduces waste of fuel, the Bureau of Mines in this bulletin presents for the benefit of those in charge of boiler plants and all other persons interested detailed information on methods of sampling and analyzing flue gases, and on the utilization of the analyses in promoting boiler-room economy. This bulletin is intended to be a companion to Technical Paper 80,a and is written in plain and nontechnical language, as far as possible, so that it may be readily understood by persons who have not had the advantage of a technical education. Whenever possible, illustrations of apparatus and methods of handling have been used rather than elaborate descriptions.

Jan 1, 1915

By J. J. Gilman

The dependence of ortho kink-band formation on crystal orientation, on temperature, and on the conditions at the ends of a specimen is described. Load-compression curves for crystals that kink are presented. The reversibility of ortho kinking is demonstrated, and motion of kink planes through crystals is shown. Finally, a phenomenological explanation of ortho kink-band formation is given. ORTHO compressive kink bands (Fig. la) were discovered for the case of metals by Orowan,1 and they have been discussed by Jillson2 and in some detail by Hess and Barrett." However, their history in nonmetallic crystals is considerably older. It is not known when they were first observed in mineral crystals, but descriptions of them may be found as early as 1885.* They were sometimes mistaken for twins.6 Mügge seems to have been first to realize their true nature and importance. He reviewed the knowledge of them for a wide variety of crystals: anhydrite, antimonite, kyanite, vivianite, gypsum, mica, graphite, molybdenite, barium bromide, cal-cite, sodium nitrate, and barite. Also, the "twins" observed by Bridgman7 in sapphire crystals resemble kink bands more than twins. The terms ortho and para kink bands have been coined in order to distinguish between two types of kink bands which seem to represent the same geometrical configurations, but which have different origins and sizes. Ortho kink bands are the usual type that form at low loads when zinc crystals are compressed parallel to the basal plane. Para kink bands form at much higher loads in highly deformed crystals. These terms refer to compression phenomena and are not to be confused with analogous tension phenomena such as tensile kink bands and deformation bands. Mügge described the geometry of ortho kink bands quite completely for kyanite crystals, Fig. lc. The geometry observed for cadmium by Orowan1 and for zinc by Hess and Barrett3 is very similar to that described by Mügge. (See Hess and Barrett for a complete discussion.) Mügge associated kinking with bending combined with basal slip. He pointed out that the kink angles

Jan 1, 1955

By CHRISTOPHER D. HEBERT, SCOTT W. HOFFMAN

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2019

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980