Search Documents

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By John R. Bartels

This Bureau of Mines report describes the development of a preliminary design for a novel, protected, cab-shuttle car for use in working seam heights down to 40 in. Because of the severe restrictions imposed by low-coal operation, Mine Safety and Health Administration (MSHA) regulations only require canopy protection on shuttle cars operating in seam heights of 42 in or greater. MSHA routinely grants variances for canopy use in seams 48 in high or less. The design was generated by giving the operator needs equal priority as related to machine performance parameters. Cab-shuttle car concepts that led to the recommended design are described, along with criteria and testing used to evaluate their potential effectiveness.

Jan 1, 1988

By Andrea Taurino

Innovation means implementing a new product or a product that has undergone significant improvement over time, in terms of method, form and performance. Innovation encompasses all the scientific, technological, organizational, financial and commercial steps that need to be taken to put it into operation. Innovation combined with research and development makes it possible to perfect the product with consistency over time. Taking inspiration from the bases developed by the Austrian economist Joseph A. Schumpeter back in 1911, Danieli came up with the concept of “Innovaction” – a combination of Innovation and Action, to refer to the development and advancement of various products for the steelmaking industry, including the loop laying head for wire rod.

Aug 17, 2017

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

The contiguous Kotre Basantpur and Pachmo (KBP) coal blocks in the Hazaribagh District of Jharkhand State in east India are being developed by Tata Steel Limited (Tata Steel) to supply coking coal to a new steel mill at Kalinganagar in Orissa.The planning challenges are many. The multiple coal seams range in thickness up to 6 m and extend to nearly 500 m depth, with dips up to 25¦ and highly variable quality. Several normal faults with throws up to 150 m intersect the deposit. There is little room for waste dumping on the lease, several large nalas (seasonal creeks) cross the blocks, and the KBP leases are not contiguous with Tata Steel's existing mining operations at West Bokaro. Geotechnical conditions, while not well defined at this stage, are largely unfavourable. There are several villages on the blocks, and extensive paddy fields. In 2009, Adelaide Mining Consultants Pty Ltd (AMC) completed a Detailed Project Report (DPR) for a production level of 8 Mt/a. A terrace mining system was proposed using 28 m3 hydraulic excavators and 185 t trucks working horizontal up-dip slices. Subsequently the viability of in-pit crushing and conveying was assessed, but the full results were not available for this paper.It is planned to extract a total of 147 Mt of raw coal at a strip ratio of 5.2 bank cubic metres per tonne (bcm/t). The planned maximum pit depth is over 300 m.The project includes a washery, a 2 + 25 MW fluidised bed power station to utilise all the coarse washery rejects, and a railway spur line to carry the washed coal to the railhead some 7 km distant.

Dec 6, 2010

By Lee Nichols

Convergent Bitumen Recovery Context of discussion It should be noted that the CBR process is a conceptual bitumen recovery feed methodology, designed to provide supplemental bitumen to the oil sand operations of Northern Alberta. To date the following have beencompleted. ?Bench Scale testing. ?Peer group brainstorming. ?Energy Balance ?Confidentiality agreements have been signed with several companies Discussions are ongoing with industry and although conceptual atthis stage the process holds significant promise.

May 1, 2007

By Cocquio D. S, Bauchau C

In the course of an integrated airborne survey in 1975, a uranium-molybdenum deposit was discovered by Minatome Australia Pty Limited in North Queensland, Australia, approximately 70 km by road west of Townsville.The mineralization occurs in a welded tuff unit within the Carboniferous St James Vokanics. It is structurally controlled by a complex of subvertical east-west fractures and is exposed over a strike length of 350 m. Drilling has traced a further 150 m extension underneath a barren capping consisting of a thick pile of vokano-sediments. The maximum width of the orebody is 150 m, and its vertical thickness is approximately 100 m.The primary ore minerals are coffinite, pitchblende and molybdenite, accompanied by various alteration products (particularly uranium molybdates).The vein-type mineralization is considered epigenetic.A comprehensive program of surface drilling and underground exploration is in progress to establish the uranium and molybdenum reserves.

Jan 1, 1980

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By G. Kelly

A new minerals engineering education programme is being developed in Australia which aims to provide tertiary institutions with a package of educationally sound, high quality courses for undergraduates, postgraduates and professionals. The programme is jointly funded by the Minerals Council of Australia (MCA) and the Department of Education Training and Youth Affairs (DETYA) and brings together academics from a number of leading Australian universities, each developing modules in their particular area of expertise. The University of Queensland (UQ) and the Julius Kruttschnitt Minerals Research Centre(JKMRC) are jointly responsible for modules in several areas including comminution, physical separation and circuit design and optimization. Other modules are being developed by the University of South Australia (with the Sir Ian Wark Centre), Curtin University and Murdoch University. The major challenge of the programme is to provide a high standard of education that is accessible to students who may be located at several different institutions and some of whom maybe a long distance from the primary course leader. Rather than taking existing course material and putting it ‘on the web’, the programme aims to improve on past teaching practice through creative pedagogy and the development of interactive multimedia learning resources. Communications technology is used in an unobtrusive way, and the World Wide Web is used to create a flexible, user-friendly learning environment rather than to facilitate delivery of content. This paper describes the instructional design template currently being used and results of early implementation trials with groups of local and remote students.

Jan 1, 2003

By Henry Kreisinger, L. P. BRECKENRIDGE, WALTER T. RAY

The investigations of fuels conducted by the technologic branch of the United States Geological Survey had their inception at the Louisiana Purchase Exposition in 1904. By an act approved Febru- ary 18, 1904, Congress authorized the work of analyzing and testing at the Louisiana Purchase Exposition the coals and lignites of the United States, under the supervision of the Director of the United States Geological Survey. An appropriation of $30,000 was made for this purpose. In the general deficiency bill dated April 27, 1904, the sum of $30,000 was added to the appropriation. To carry out these investigations the Director of the Geological Survey appointed a committee consisting of E. W. Parker, statistician of the Geological Survey; Joseph A. Holmes, State geologist of North Carolina; and Marius R. Campbell, a geologist of the Geological Survey. Under the first act authorizing this work all of the machinery and coal for the tests was to be furnished the Government free of charge. The buildings containing the testing apparatus were all paid for out of the first appropriation. After the close of the Louisiana Purchase Exposition every Congress made an appropriation for continuing these fuel tests. These subsequent appropriations permitted the purchase of appliances better adapted for the testing work.

Jan 1, 1912

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational 'silos', inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By V. A. Cammarota

In this report, the effects of anode-production variables, such as aggregate coke sizes, pitch binder content, and baking cycle, were investigated. A small alumina reduction cell proved effective in evaluating anodes prepared from commercial materials and from lignite coke and pitch. Compressive strength was found to be the physical property most significantly influenced, but it did not appear to affect anode consumption. Specific carbon consumption, that is, the ratio of carbon in the anodic gas to carbon theoretically oxidized at the anode, was used as an index of anode consumption. It was found that an anode made with lignite coke and commercial pitch was very low in consumption; however, anodes made completely from lignite but by a different fabrication method showed high consumption and anode deterioration. Microscopic examination of anodes after electrolysis showed evidence of higher consumption at low current densities, and was useful in judging overall anode quality. Based on the physical properties of the anodes and their consumption during electrolysis, lignite can be a suitable material for anodes, provided the proper fabrication conditions are used.

Jan 1, 1970

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002