Search Documents

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By John Wellington Finch

INVESTIGATIONS by the Bureau of Mines of deposits containing strategic minerals were authorized by what has become known as the Strategic Materials Act (Public No. 117, 76th Congress, Chapter 190. 1st Session). A later act providing an appropriation for the first of four years through which the investigations are to be conducted was signed on Aug. 9, 1939. No time has since been lost as seven field projects already are being vigorously prosecuted, and two others no doubt soon will be in course of execution. Project engineers were at their stations within two days after funds had been made available. Crews have been hired; equipment and supplies have been purchased; 5 bids for diamond drilling have been obtained and the drilling has started base camps have been established: ground has been cleared; and several thousand feet of trenching, test-pitting, and sampling have already been done. At the Reno Experiment Station of the Bureau, a special metallurgical laboratory has been provided to make assays, analyses, and tests upon samples of ores from all projects under investigation.

Jan 1, 1939

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By M. R. TECK, N. Rudd, L. K. Thomas, D. L. Katz

The authors are to be congratulated for presenting the first comprehensive paper on the theory and practice of threshold pressure determination in connection with underground gas storage. It is of particular value since most previous experimental work on this subject has been proprietary to the commercial laboratories engaged in such testing and to their clients. This dlscussion is presented in amplification of the subject paper, not in criticism, and is based upon our experience with approximately 5,000 threshold pressure determinations. Our comments are directed primarily to the experimental procedures as described by Thomas et al. It should be noted that, while clay mineral-rich lithologies are the most common caprock materials, the samples used (Table 1) include low permeability sandstones and carbonates, but do not include shales or other formations in which clav minerals exert a dominant effect. While our experience on samples analogous to those investigated by the authors generally confirms their findings, we have found that even more rigorous experimental conditions must be imposed where clay minerals are the controlling factor. These additional conditions result from the well-known molecular character of the clay minerals themselves in which water is interlaminated with, and bonded to, silicate sheets, thus becoming an essential component of the molecule. In many clay minerals the character of the intersheet bonding, and thus the dimension of the lattice, is strongly affected by variations in the identity and concentration of cations present in the intersilicate water. On a supermolecular scale, adsorbed water films on particle or "flakes" of shale provide much of the cohesive force necessary to maintain mechanical strength. The thickness of these films is variable and inversely proportional to intergranular pressure within the dimensional limits involved in caprock investigation. The thickness of the intersilicate water layers may also be subject to pressure under some conditions. These considerations are reflected in several necessary modifications of the experimental procedures described by the authors. Two of these are, in our judgment and experience, of such importance that they cast real doubt on the validity of data obtained on argillaceous materials without their application. The very careful resaturation procedures proposed by the authors should give good results in connection with the relatively "inert" lithologies used in their experiments. Our experience suggests, however, that they would create more problems than they would eliminate if applied to argillaceous materials. 1. Drying of the sample at the temperature and for the duration indicated by the authors not only will dessicate the sample with consequent shrinkage cracking, parting along bedding planes, and even total disassociation in the case of fissile shales, but it may also alter the character of the clay minerals themselves — in some cases irreversibly. 2. Prolonged evacuation to 2 microns Hg further dessicates the sample and is even more effective in reducing the intersilicate water content. 3. Resaturation with water differing in pH or chemical content from that existing originally in the sample also serves to alter the nature of the sample, particularly its structure and strength. 4. Our experience has been that, even with the thorough precautions proposed by the authors, complete resaturation of very fine grained materials is rarely obtained. Yet our experience confirms the

Jan 1, 1969

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it&apos;s formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water inflows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk.

Jan 1, 2013

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002