Search Documents

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15 mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150 mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented . A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: Hydraulic hoisting, slurry

Jan 1, 2004

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

The placer gold industry has experienced a roller-coaster history incorporating four major boom eras. The first, 'hand-methods' boom arose in the mid-19th Century from application of an old idea in new places around the globe. The subsequent hydraulic mining, bucket dredging, and 'hydraulic excavator-portable plant' booms each arose from application of new ideas in old places around the globe, ie in places where gold had been found during earlier booms. The new ideas that heralded the second, third and fourth booms were all significant advances in excavation technology. These enabled the industry to target the known deposits that were too deep, too wet, too small, or too low-grade for recovery by earlier boom methods. Relatively few new deposits or new deposit styles arose from the 'history book' exploration approach, so the number of known deposits to which each of the boom methods were applicable was limited. Consequently, the first three booms were each followed by significant periods of industry decline, and the fourth boom is currently waning inNew Zealand. Further decline is not inevitable and can be avoided by changing to a knowledge-based exploration approach similar to that adopted by the hard rock gold industry in the 1970s. Such an approach could easily herald the next placer gold boom.   Most of the relatively coarse, easily won alluvial gold in proximal and medial reaches of the active placer systems is gone. However, a substantial alluvial gold resource remains in the distal reaches of active systems, and in ancient placers formed onshore and on the continental shelf during previous sedimentary cycles. The resource in these deposits probably exceeds the total New Zealand placer production to date. Successful development of these placers requires application of robust geologic models for the formation and distribution of the placers through time, and advanced exploration technology that has not been used before in New Zealand. Nevertheless, the knowledge and technology required to explore and mine these deposits is available now. Many of these deposits contain a large proportion of problematic gold types that are difficult to recover with the commonly used gravity technology without sustaining significant losses. Despite advances in recovery technology in last few years, too much emphasis is placed on the incorrect assumption that gold size is the primary control on recovery efficiency. Other gold particle parameters, especially particle shape, exert a much greater control on whether gold will be saved or lost to the tails, and must be considered in the design of recovery technology and configuration of recovery circuits.

Jan 1, 2003

By William K. Connor, O&apos

The U.S. Bureau of Mines (USBM), in cooperation with the American Society of Mechanical Engineers (ASME), conducted over 200 hours of melting tests to vitrify residues from five municipal waste combustion facilities. Combined residues (grate residue and f1yash) from three municipal waste combustors, a waste water treatment sludge combustor, and flyash from a refuse-derived-fuel (RDF) boiler, were sequentially melted in a I-metric-ton (mt) water-cooled-wall electric arc furnace. Each of the residues underwent magnetic separation, screen size analysis, and bulk chemical analysis prior to melting. The furnace products were examined by optical and electron microscopy and by X-ray diffraction. Bulk chemical analyses were acquired for the metal, fume, and vitrified furnace products. The material balance for the furnace operation indicates that from 69 to 86 pct of the feed reported to the vitrified furnace product, which had leaching potentials well below the EPA limit for each metal, as determined by the EPA TCLP. The electric arc melting furnace currently is being utilized in a cooperative research project between the USBM and the Idaho National Engineering 'Laboratory (INEL) for melting tests on simulated low-level radioactive wastes,

Jan 1, 1991

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By C. B. Manula

This report is mainly concerned with the modification and development of a users manual for the Open-Pit Materials Handling Simulator (OPMHS) developed at Penn State. Model Modifications included the introduction of a free-format input, the application of a Weibull random generator, facilities to stochastically simulate shovel-dragline operations, and routines to increase the flexibility in making truck assignments. At the same time, core storage requirements and execution times were minimized and all P.S.U. conventions were removed to allow operation on other computing systems.

Jan 1, 1976

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By Charles F. Coleman

Kinetics studies and other rate measurements are reviewed in the amine extraction of uranium and of some other related and associated metal ions. Equilibration' is relatively fast in the uranium sulfate systems most important to uranium-hydrometallurgy. Significantly slow; equilibration-has ' been encountered' in some other systems. Most of the recorded rate information, both qualitative and quantitative; has come from exploratory and, process-development development work, while some kinetics studies have been directed specifically toward elucidation of, extraction mechanisms. In contrast to some other extraction systems, relatively little attention has been given to the kinetics of uranium extraction by amines. This is because investigators have not been troubled by slow extractions. Instead, when rate limitations have been of concern in amine extraction (Amex) process developments, they have been mainly from slow phase disengagement rather than from slow equilibration. Nevertheless, taking uranium together with several other elements that are closely related to it or associated with it in typical processes, a considerable body of rate information has been recorded.

Jan 1, 1979

By Thomas Glück

Established and emerging mining companies face significant challenges in managing their operations and projects. Outcomes often do not meet the expectations of all the stakeholders of particular developments. This paper reviews typical management practises used by mining companies to undertake mining projects and improve their operations. A simple application of the House of Quality (HOQ) tool used in the Quality Functional Deployment (QFD) management approach is presented. It is shown that a QFDMMPtg approach could lead to innovation in mining processing plant development practice.

Jan 1, 2015

By Ralph B. Stevens

The objective of this 20-month program was to define the relationships between mine ventilation, temperature, humidity, ore properties, material's used in mine operations, etc., and the spontaneous combustion problem in underground metal mines. Tradeoff studies of availability, reliability, cost, and maintenance of spontaneous combustion protection sensors and telemetry were conducted, after which a prototype system was selected from four design alternatives. This selected system was then laboratory tested and demonstrated in an underground copper mine.

Jan 1, 1979

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

By Paul M. Tyler, Colin G. Fink

THE field of rare metals is so broad that progress can be reported upon many important fronts. Not satisfied with the 92 elements that Mendeleeff and his followers have accepted as legitimate, scientists are trying now to complicate matters by making new elements. Enrico Fermi announced the fabrication of "Element 93". Uranium, instead of being allowed to disintegrate slowly according to its normal habit, was bombarded with neutrons until some of them seemed to have stuck in the nucleus. To understand just what is alleged to have happened all one has to do is to line up the elements in their usual order of ascending atomic weight and imagine, as physicists do, that each atom is a little solar orbit comprising a central mass or planet about which other masses revolve like satellites. Ordinary hydrogen, being very light, consists of only one positively charged proton center, with only one positively charged electron revolving about it. Other atones are progressively more complicated until we come to uranium, which has a relatively big center and 92 particles revolving around it.

Jan 1, 1935

Major producers posted 25¢-per-pound increases on cadmium, raising their domestic quotes to $2.75 per pound. COBALT: Cobalt consumption in February, exclusive of salts and driers, increased by 21 percent compared with consumption in January. Significant increases in consumption occurred in cutting and wear resistant materials, welding and alloy hard-facing rods and materials, magnetic alloys, and other alloys. The major sales agency for cobalt in New York reportedly announced price increases, effective April 15, 1976, for cobalt metal, powders, and oxide. The new price for 250 kilo (551 lb.) drums of cobalt metal (granules or electrolytic cathodes), f.o.b. Port of New York, was quoted at $4.40 per pound. This is the first cobalt price increase since January 23, 1975, and is the result of a price increase by Sozacom, the official Zairian sales agent. Other cobalt producers are expected to raise their prices in line with the new quote.

Jan 1, 1976