Search Documents

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By K Belanger, J. Mclachlan, F. Stober, G. Norval, B. Snider, A. Munsch, T. Koehler, E. Piantino, J. Carlos Queiroz

The project to rebuild the smelting furnaces at the Anglo American - Barro Alto ferronickel smelter, located in Goias, Brasil, was initiated in September 2013. To optimize the capital cost, while maximizing furnace integrity and robustness, a design basis giving flexibility to ore composition variation was developed in order to ensure sustained nameplate production. The resulting capital efficient, fasttracked project execution was accomplished through the creation of an integrated project team of Anglo American and Hatch through FEL 3 and FEL 4 phases of the project. The integrated team addressed the project challenges through a cooperative and versatile approach, created by access to knowledge, experience and systems in both Anglo American and Hatch. The team could operate at an optimized speed of execution, as demonstrated in the FEL 3 and FEL 4 completion durations, as well as efficiently mitigating any risks of increasing cost or delaying schedule by utilizing lessons learned and team knowledge from Anglo American on the original green-field project and Platinum smelters and Hatch on similar reference ferronickel furnace rebuilds. Other critical drivers of project cost minimization and revenue loss/generation (considering production revenue of each furnace) are scheduled durations for construction, commissioning and ramp-up. The integrated team commenced construction, commission and ramp-up planning almost one year in advance of the shutdown and this paper will discuss the strategies developed to reduce risks and optimize the construction schedule to mitigate revenue loss and optimize ramp-up time to sustained operation at nameplate capacity.

Jan 1, 2015

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

(Under this heading will be published notes sent to the Secretary of, the Institute by members or other persons introduced by members.) Development and production. Member open for engagement. Past year in war mineral field work, operation and production. Ten years' thorough experience in both subordinate and executive positions, gold, silver and copper in the United States, Mexico, and South America. Age 37, married. Minimum salary $3600. Interview. South or East. A-577. Engineer and executive. Captain U. S. Army, age 36, expects discharge before July 1. Seven years' mining and metallurgical experience. Six years with large technical college as assistant professor of mining and directing extensive experimental work. Desires position as executive or research engineer with reliable company or as professor of mining with first-class college. A-909. Mining engineer. Twenty-five years' experience including mine and works operation, construction, plant installation, and mine examination. Speaks Spanish. A-1173. Metallurgical engineer. Twelve years' laboratory and operating experience, covering copper blast furnace, roasting, reverberatory smelting and latest Cottrell treater practice on copper dust and zinc dust. Technical graduate. 36 years of age, married. Highest recommendations. Open for immediate engagement. A-2354. Mining engineer. Junior Associate. At liberty about July 1. Captain Heavy Artillery. Single, age 24. Go anywhere. Best refer-ences. A-2843. Engineer. Age 26, single, graduate Missouri School of Mines, B. S. in Mis. Met. E. Desires position with oil or metal company in any capacity. Location immaterial. At present engaged, desires change. A-2844.

Jan 7, 1919

By THOMAS LEONBRD WATSON

I. INTRODUCTION. THE results embodied in this paper are based on a careful field- and laboratory-study of the lead- and zinc-deposits of the Virginia-Tennessee district, begun in the latter part of the summer of 1904 and completed in the spring of 1905, preparatory to the publishing of a State report .on them. A separate description of the individual deposits in Virginia is purposely omitted, since I have already described them in considerable detail in a State report. The Tennessee deposits are described here in some detail for the reason that no detailed record of them has yet been published. Practically, this paper summarizes the results obtained from a study of the geology of the ore-deposits of the district as, a whole. (I had the pleasure of visiting the deposits of Virginia and Tennessee with Dr. H. Foster Bain of the U. S. Geological Survey, in April, 1905. Figs. 21 and 22 are from photographs taken by Dr., Bail.) II. HISTORICAL. . The first authentic records of lead-mining .in Virginia date hack more than 150 years; and the old lead-mines at Austinville, on New river in Wythe county, V a., were the first to be worked. Colonel Chiswell, a native of Wales, and one of the earlier adventurers in southwestern Virginia, was one of the first operators of the Austinville mines. Chiswell's operations at Austinville commenced in the year 1750, and closed shortly after the beginning of the Revolutionary War, in the' year 1776, covering a period of about 25 years. From that time to the present, mining has been carried on almost continuously in the Virginia area. For many years after the Virginia mines were operated, mining was confined exclusively to the lead-ores. The zinc-ores

Mar 1, 1906

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By C. W. K

This little sketch of the late Willet G. Miller, Provincial Geologist of Ontario, is intended to be neither a biography of his career nor a eulogy of his life. His biography has already been written in an incomparable manner by Mr. T. A. Rickard, his eulogy by Canon Cody. What more can be said of Dr. Miller than is summed up in the words of that great Canadian divine, Canon Cody, that he was "Big in body, big in heart, and, as we learned, big in brain." This article, then, will merely record a few personal reminiscences of the man himself, and while they are necessarily disjointed, they may at least serve to illustrate certain traits in his character which are not generally known or appreciated outside of the circle of his intimate friends. In the latter part of May in the year 1904, Willet G. Miller, with two? assistants, set out for the small village of Haileybury to begin his geological work in the area a few miles to the south which he was soon to name Cobalt. At that time the Timiskaming and Northern Ontario railway was not finished, although the right-of-way was cleared and partly graded. The nearest railway station was on the Canadian Pacific at the south end of lake Timiskaming, from which point the old steamer Meteor carried passengers and freight up the long, narrow and deep waters of lake Timiskaming, a very pleasant trip of some sixty miles. On this particular trip there was a fairly large crowd on board consisting of settlers going into the clay belt north of lake Timiskaming, of lumbermen, and of a few merchants and commercial travellers who were interested in the small business centres of Haileybury, New Liskeard and Ville Marie. Scarcely any attention was paid to the reports of the newly found silver deposits, although the daily papers had announced discoveries in the district six months before. As a matter of fact, the chief excitement on board was afforded by a moose, which, in swimming from the Ontario to the Quebec shore of the lake, crossed the bow of the boat, the captain steering to within a few yards of the terrified animal.

Jan 1, 1925

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By Simon D. Strauss

This article is part of a presentation Strauss made Dec. 3, 1988 at the sixth annual American Mining Hall of Fame (AMHofF) banquet in Tucson, AZ. At the banquet, the Mining Club of the Southwest honored Strauss by naming him the 1988 recipient to the AMHofF. (Industry newswatch, page 6). Introduction In the last two decades, there have been two previous periods of sharply rising copper prices. One was in 1973-74; the other in 1979-80. In both cases, a short period of high copper prices was followed by steep and prolonged periods of low prices. In the language of the market analyst, the high prices were called spikes. Is it likely, then, that three or four years from now the present price of copper will show up as a spike in the charts? There are substantial differences between the current position and the markets of 1973-74 and 1979-80. In 1973-74, US copper prices were subject to government-imposed price ceilings of $0.60 per lb through early December, 1973. These were increased to $0.68 per lb through May, 1974. Meanwhile, mines outside the United States were free of restraint. Rising demand in London pushed the price above $1 per lb in the third quarter of 1973. In early April 1974, it reached a peak of $1.50 a lb. In May of that year, the US ceilings were removed and the domestic price began to rise. What were the causes of this price strength? While ceilings held the domestic price below the world market, domestic consumers acquired all the tonnage offered by US mines. Meanwhile, in the world market, buyers feared prolonged shortages. The Club of Rome had warned that world economic growth would be limited by impending depletion of mineral resources. There was al so concern about a copper cartel that might increase copper prices even more. In early 1974, at a special United Nations session, developing-country spokesmen warned the industrialized world to expect high commodity prices. Also adding to the concerns of copper buyers was the fear that when US wage contracts expired in mid-1974, protracted strikes might ensue. The combined effect of this atmosphere was that consumers accumulated large amounts of copper, far above their normal carry. By midsummer, the position changed radically. While some strikes did occur in the United States, they proved short-lived. The most significant development was a massive economic recession. The energy crisis was causing enormous dislocations in the world economy. Construction activities were sharply reduced and automobile sales plummeted. Public confidence was shaken. Copper sales fell precipitately as consumers decided to draw down their swollen inventories. The price came down too. In April 1974, the London price- as noted-was $1.50 per lb. By the end of the year, it was down to $0.57 per lb. In 1973-74, the copper price rise was fed by fears of shortages, cartels, and strikes. In 1979-80, the market rose on the strength of good demand plus political and military instability. The price rise was also fed by inflationary trends, exemplified by speculation in precious metals. Prior to this second spike in copper prices, the market had been depressed despite economic recovery. Despite reduced US output, copper production in the rest of the world was increasing. Though consumption was rising, surplus stocks reached unprecedented levels. At the end of 1977, the aggregate of stocks at the refineries and in the exchange warehouses was 1.5 Mt (1.67 million st). That was more than three months' shipments at then rates of consumption. In 1978, the statistical position improved. Shipments of refined copper that year were 8% greater than in 1977. The result was reduced visible stocks but -just as was to be the case in 1984-86 - the price remained depressed. In 1979, an even sharper drop in visible stocks occurred as shipments rose by another 4%. This time, though, the price responded. In December 1978, the price in current dollars had been less than $0.70 per lb. By the end of 1979, it was above $1 per lb. And in the first quarter of 1980, it averaged more than $1.20 per lb. Military and political developments were a factor. The hostage crisis in Iran was followed by the Soviet invasion of Afghanistan. To many, it appeared that war might result if the Soviets pushed on into Pakistan. At the same time, speculation drove gold and silver prices to incredible levels. As silver prices rose above $40 per oz), copper above $1 per lb did not seem unreasonable. Then, in March 1980, the precious metals price boom collapsed. Copper prices also retreated, though not as much. In February 1980, the copperprice averaged $1.32 per lb. By December, it had dropped to $0.85 per lb. In 1981 and 1982, the decline continued. The present copper situation Why is the current situation different from these two previous episodes of high prices? First of all, today's inventories are far lower than they were in either 1974 or 1980, when the price declines began. The stocks at refineries and in exchange warehouses are substantially less than they were then. More significantly, consumers today have very limited holdings compared with stocks they carried in 1974 and 1980. Even if faced with a downturn in their own business, copper consumers will not be able to stay out of the market. To the extent they have any business at all, they will have to buy copper. And on the supply side, there is also a significant difference. The year 1988 has been unusual. US production is up sharply, responding to higher prices. But production is little changed in the rest of the Free World. Indeed, several of the major producing countries have mined less copper this year than in 1987 despite the prices increases. Peru has had labor problems that have cut its output. Zambia and Zaire suffer from shortages of expatriate technicians, not to mention spare parts. They also suffer from the failure to maintain equipment or perform adequate development. In Chile, the two largest mines, Chuquicamata and El Teniente, have not met their production targets. Chuquicamata is struggling with high arsenic content in its ore. And, in late 1987, severe rockbursts hampered operations at El Teniente. In addition, depletion of some mines in Australia and South Africa has offset rising output at other properties. Indeed, when final mine output figures for 1988 become available, it may well be

Jan 1, 1989

This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health (NIOSH) from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health. At both deep and shallow cover instrumentation sites, surface subsidence measurements, subsurface in-place inclinometer measurements, and underground pillar pressure measurements were conducted as longwall panels were mined. Comparisons of the deep and shallow cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario. Under shallow and medium covers, measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Conversely, measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers. However, FLAC3D simulations of the casings indicate that, in all three cases, the P-110 production casings remain intact under longwall-induced deformations and compressions, which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.

Jan 7, 2020

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971