Search Documents

By Leonard Obert

Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillar, arches, and other structures. The method required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E = V2d ...(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.

Jan 1, 1940

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By Leonard Obert

[Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillars, arches, and other structures. Tin r Loa required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E V2d .....(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.]

Jan 1, 1940

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010

By James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department?s Bureau of Labor Statistics? Census of Fatal Occupational Injuries, Survey of Occupational Illnesses and Injuries, and Current Population Survey. Between 1992 and 2002, 3378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 to 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992?1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002 but showed overall improvement from 1995 to 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100 000 workers. In addition, 46 598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. The research of the National Institute for Occupational Safety and Health aimed at evaluating commercially available overhead power line proximity warning alarms is described. This paper is expected to be the initial step for eventual development of a performance standard for such systems.

Jan 1, 2008

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By Takuji Yamamoto

High-speed TBM excavation requires rapid ground assessment ahead of excavation, particularly in complex grounds. The Tunnel Reflector Tracing technology (TRT) developed by authors, uses seismic reflections to produce volumetric images of ground anomalies. To further minimize interruption in the TBM excavation the authors modified surveying technique switching from cable (wired) to radio (wireless) data acquisition system. This paper presents the outline of the Wireless TRT system, and compares the results for the wired and the wireless surveys. The comparison shows that the wireless system offers high precision data, is more efficient and economical and significantly less intrusive in tunneling operations.

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

By Eric Nordhausen

This report and associated deliverables is the culmination of a comprehensive literature survey, data collection and identification of over 500 metal/nonmetal active mines/mills/smelters (over 50,000 tons per year, TPY, production) in the contiguous 48 states. The main purpose was to compile an inventory of the mine/ mill/smelter waste tonnages, thus forming a data base for future research and development in improving waste management and waste disposal techniques in the metal/nonmetal mining industry. The study specifically excluded sand and gravel, sulfur, granite and any commodity that leaves basically no waste when mined and/or milled. The coal waste inventory is the subject of another report. The study provided for locating, mapping. encodating and digitizing all the mine/mill/smelter information made available throughout the nation as well as the climatological, land use, topographical, ecological and vegetative data. Mine/mill/smelter information also included (where possible) acreage and/or volume, mining methods, primary ore and gangue minerals, waste composition and haulage methods and distance hauled. Finally, a discussion is provided concerning present and potential uses of various types of tailings, as well 8S recommending possible R&D in addressing problem areas in waste disposal techniques and management.

Jan 1, 1981

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Charles Jones

IN the winter of 1902, while occupying the position of mining and examining engineer for the Mountain Copper Co., Ltd., of Keswick, Cal., I had occasion to discuss with the General Manager, among other things, the question of the enormous waste of sulphur in smelting cupriferous, pyrite ore, and to cast about for means to utilize this waste or to render the fumes innocuous to vegetation. The decreasing rate of production of California farms, the consequent need of fertilizers, and the opportunity thus offered to utilize large quantities of sulphuric acid in the manufacture of superphosphates naturally brought the subject to the practical and commercial side of phosphates. I was informed that the company had made efforts to find phosphates in the West, without success. I advised as a start placing inquiries for phosphate deposits on the Pacific coast in the current mining ,journals. This was done, with the result that in January, 1903, from an advertisement in the Mining and Scientific Press we got track of a deposit in Rich county, Utah, through T.J . Wilson, of the Southern Pacific railroad in San Francisco. As soon as snow in the mountains would permit, in May, 1903, I undertook an examination of the property, with the result of recognizing the importance of the find, in spite of its lack of facilities for transportation at a commercial figure. On June 15, 1903, I concluded my report by saying, "This may be one of the world's deposits of phosphates." On Nov. 17, 1903, I concluded my report for the season in the following words : " I have now no hesitation in saying that I believe the Carboniferous formation so largely developed in the Wasatch mountains of Utah and the mountains of the Great Basin will prove to be one of the greatest storehouses of phosphoric acid in the world."

Jan 10, 1913

H. DEAN JACOT RMCMI PRESIDENT 1987-1988 on behalf of The RMCMI Board of Directors and Officers The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 84th Regular Meeting and Convention to be held June 26, 27 and 28, 1988 at Beaver Run Resort Breckenridge, Colorado

Jan 1, 1987

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By B. W. Gandrud

This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests made by the Bureau of Mines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers The Klondyke mine, operated by the Blocton Mining Co., is about 1 mile east of West Blocton, Bibb County, Ala., near the southwestern extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/, one on the tabling of fine coal from the Thompson and Woodstock bed , and the third a washablility study of the Henry Ellen bed at Acmar6/.

Jan 1, 1939

By M. R. HULL

FOLLOWING the discovery of a body of ore that appears to have commercial possibilities there is a period of development work to determine its extent and grade and the most economical method of mining it. Laboratory tests are made in an effort to determine the most practicable and economical treatment for the extraction of the valuable constituents of the ore and these tests are carried farther and checked in a pilot or test mill. The rate at which the ore is to be mined and the daily capacity of the plants that are to treat it will depend on a number of important factors such as: The size of the orebody; the capital available for building the plants; the market or demand for the final product; the supply of skilled and common labor available for the construction, operation and maintenance of the plants; the quantity and quality of available water, and the amount and cost of power that can be purchased or that can be economically developed. Having decided on the treatment that is to be given to the ore and after full consideration of the above factors the management decides to erect a reduction plant of a given capacity.

Jan 1, 1926

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

By Pamela J. Watson

This report presents a Bureau of Mines literature survey that provides a data base useful for current and future studies in the area of chemically enhanced drilling and cutting. Publications describing laboratory testing and field studies of drilling and cutting with chemical additives are reviewed. Significant results are summarized and tabulated by rock or material type and also by chemical additive, with extensive references. Selected studies related to fluid-enhanced processing or material testing are summarized in the appendixes.

Jan 1, 1985

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The use of phosphorus by mankind is long established. From use in agriculture, foods, high tech electronics, and more recently in EV battery cathode production, one cannot escape its impact on today’s society. This paper will review and describe the circular journey of phosphorus through its value chain from the mining operation of phosphate ore through beneficiation into downstream chemicals production and finally into the EV battery cathode production space. This will include a review of phosphoric acid production from phosphate concentrate using wet process route and thermal route. The wet process route discussed will be via dissolution of phosphate concentrate by sulphuric acid. The thermal route will discuss thermal decomposition of phosphate concentrate using submerged arc furnace to produce yellow phosphorus followed by its combustion to produce phosphorus pentoxide and subsequent hydration to produce phosphoric acid. It will also discuss briefly other phosphate derivatives for specialty chemicals and recovery of phosphorus units from wastewater treatment plants, sewage sludge and incinerator ash. Finally, the paper will discuss the use of phosphorus in EV batteries in the form LFP cathode materials and its production. It will also briefly discuss the LFP battery recycle.

Sep 11, 2023