Search Documents

By Anthony Wakefield

Dredging tends to be either horizontal or vertical. In each case solids have to be disengaged from the deposit, mobilized, acquired and elevated or translated. One means of elevation is the airlift. Elevation and translation of essentially granular material nay be by jet pump or centrifugal pump. Any of the three types may be used on its own. The airlift and jet pump may he combined for vertical transport and the centrifugal and jet pumps for predominantly horizontal. Both suction point and pipework must have a means of deployment from the surface or from a submerged vehicle or merely a diver. An airlift is an energetic system, having a source of energy and a means of storing it. It therefore will be difficult to prevent oscillation -surging. A centrifugal pump has a characteristic that bends over at low flow rate and is therefore intrinsically unsuitable for pumping solids. The result is blockage, operation at high velocity and correspondingly high wear rates or operation at low concentration of solids and correspondingly low efficiency. The jet pump is intrinsically exceptionally stable but has a low hydraulic efficiency. The jet pump-airlift hybrid prevents or reduces surging and increases system efficiency away from the optimum depth for airlift operation. Delivered solids concentration is increased. The jet pump-centrifugal pump hybrid totally prevents pipeline blockages and increases the productivity from a given pipeline size. For a given energy input the average production is typically doubled. For example, the Indian River Delaware bypassing pipeline transmits an overall day-in-day-out average of 500t/h (tonnes) of sand down a 10.86" diameter line.

Jan 1, 1998

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By Y. C. Lo

Grinding process optimization is an exciting new tool for maximizing the performance of existing mineral processing plants. This paper discusses the methodology of optimization which involves plant sampling, pilot tests, modeling, computer simulation and plant verification. The methodology developed emphasizes the interactions among operating variables and design options. Two example applications demonstrate that AG and SAG optimization provides the basis to increase grinding throughput up to 10 percent. This sys- tem optimization technology has been proven to be very cost effective for grinding plant performance improvement.

Jan 1, 1998

By P. E. Christensen

Due to ever-increasing stripping ratios associated with the No. 8 Seam at the San Juan Mine surface operation, BHP Minerals decided to implement longwall mining for the extraction of the substantial future reserve base. In preparation for longwall developments, BHP opted to first develop a small-scale pilot operation within the No.8 Seam on an adjacent lease to address geotechnical/geological concerns related to ground control, subsidence, caving, panel and entry design, and operational issues related to entry development and proper face equipment selection. Room-and-pillar mining methods are currently being utilized to develop a full extraction panel for a wide range of geological, geotechnical, and geomechanical evaluations aimed at characterizing and assessing the mineability of the No.8 Seam. Variable roof and floor conditions, coupled with a multi-bench coal seam, require that a number of mining horizons, opening geometries, and roof and rib support fixtures be evaluated relative to expediting gate and panel developments. Issues related to development of timely caves in areas subject to overlying sand channel deposits will also be addressed through underground in-seam stress and deformation measurements, and interburden and surface subsidence monitoring. This information will ultimately be used to evaluate face support and gate and panel pillar/entry development requirements. The current depositional model for the property, developed from an aggressive drilling, highwall mapping, and lineament evaluation program, will also be refined during the Pilot Mine study through extensive in-trine mapping, additional roof and floor drilling and physical property testing, and determination of the in situ principal horizontal stress field.

Jan 1, 1998

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By J. R. Cole-Baker

An independent technical audit by a consultant is part of the accountability process of publicly owned or publicly quoted companies when raising finance through share issues or loans or the sale of equity, and of banks or development funds when granting loans. Africa is undergoing a renaissance in investment in its mining industry. It is forecast that capital investment, in major mining projects in Africa, will be over US$ 4.4 billion, in the next few years. Most, if not all, of the capital to be raised will require an independent technical audit. The aim of this paper is to assist the management of mining companies seeking finance in appreciating the role of such technical audits. The reasons for such audits, especially to attract international investment, are listed. The role of the audit is explained in assessing the underlying robustness of the company as ?a going concern? and the viability of any ?expansion plans?. Its use is emphasised in establishing the underlying value of the company based on the mine life as supported by the mineral reserves. The independent consultant role is stressed as a representative of the parties in a finance deal who cannot, in practice, carry out their own detailed and specialized technical due diligence. The various components of a typical audit are examined with examples of critical matters which may require resolution. The definitions, which are used commonly in audits, in respect of competence and reserves and resources, as stated by various regulatory bodies, are compared.

Jan 1, 1998

By Zhijing Zhang

Sodium borosilicate is the basic composition of coating materials, Vycor and Pyrex glasses. In the present study, viscosities of Na2O-Si02-B2O3 ternary melts were measured under various compositions and temperatures. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on present experimental results, the previous structure based viscosity model was modified. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. The fitting ranges of the model cover the composition of XB2O3 from 0.1 to 0.6 combined with xSio2 / xNa2O = 0.5, 1,2 and 5 respectively.

Jan 1, 1998

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor's pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998

By Thomas V. Durkin

About 1.41 kt (45.2 million oz) of gold have been ! produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection. Mining is promoted as an industry while prevention of pollution is required along with reclamation of affected lands to a beneficial use. The South Dakota Department of Environment and Natural Resources' (DENR) system of "one-stop shop- ping" for environmental permits streamlines the permit process. It fosters quick resolutions to compliance problems and helps keep enforcement actions out of the courts. Paha Sapa means "Hills that are Black" in Dakota Sioux. Appearing dark from a distance due to a thick forest of Ponderosa pine, the Black Hills were gold to many people. The exact date that gold was discovered in the Black Hills remains debatable. An inscribed stone tablet found in 1887 near Spearfish recorded these words:

Jan 1, 1998

By Thomas E. Brown

Commercd explosives have evolved through this century f?om dynamite through ANFO to the current lines of Water Gels and Emulsions. Water Gels and Emulsions evolved to counter the lack of water resistance and density of ANFO yet maintain its low cost position verses dynamite. Today, explosives must be safe and inexpensive and perform under a wide range of temperatures, function efficiently in wet or dry boreholes and have a good shelf life. Emulsions meet this criterion, which is why they are the current trend products worldwide.

Jan 1, 1998

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

Since the initial discovery of phosphate rock resources in North West Queensland in 1966, significant changes in ownership and development direction have occurred. Initially development of the resource involved beneficiation to produce a more saleable grade of phosphate rock. However more recently development has focused on the production of a high analysis fertilizer product on the minesite. These changes have been influenced by economics, industry/government cooperation and a changing phosphate industry.

Jan 1, 1998

By George Boucher, Simon Williams, Neil McBride

"The aim of these analyses was to utilise the latest available production information for the Wandoooperation to determine the optimal blasting parameters, costing’information and predicted results(fragmentation, muckpile shape and vibra.tton). Much of the data used as input was made availablefrom the information gathered during the excavation of the test pits during 1995. As with any“planning stage” analyses, many assumptions were required to fill gaps in the available data."

Jan 1, 1998

By A R. Proudman, A H. Purvis

The Granites Gold Mine Callie gold deposit is located 550 km northwest of Alice Springs in the Tanami Desert. Gold mineralisation occurs due to a complex interplay of geological factors which include but are not limited to favourable lithology, structure, alteration and quartz veining. High-grade mineralisation, while pervasive under favourable conditions, is highly variable over short distances and is very nuggetty. In contrast, the lithology and geological structures that host the mineralisation are very continuous. Orebody modelling techniques have evolved over time because of a growing understanding of the mineralisation controls. Modelling issues such as sampling and assaying accuracy, modelling method, data density, gold population statistics, geological interpretation and domaining, grade boundary and calculation conditions, and model block size are constantly being reassessed in an effort to increase understanding of the mineralisation controls and modelling accuracy. The evolution of the modelling process in response to increasing data levels and a growing understanding of the mineralisation controls has resulted in changes to the perception of the orebody size and style. This has caused the choice of underground mining method to be revised several times and the process to final mining method selection to take longer than usual. In order to achieve the planned production start-up date of July 1998 the process has been allowed to progress in parallel with development of the underground mine. This paper describes the resource modelling and mining method selection process applied to the Callie underground mine and some of the issues which have contributed to its evolution. Some conclusions that are relevant to the efficient planning and development of new mining projects in general are presented.

Jan 1, 1998

Several glacial episodes have been distinguished in the Shotover Valley. These produced fluvioglacial aggradational deposits downvalley from the terminii, commonly with well-preserved terrace treads, as exemplified near Skippers. Chronological links can be determined between the Shotover tills and sediments and assessed equivalent deposits in the Wakatipu Basin/Kawarau Valley region through axial valley profiling. Constructed relationships suggest older Shotover events were probably large and left little detrital deposits within the valley. In contrast, the younger advances were smaller and valley-constrained. They are modelled as being wholly of Waimea or Otira Glaciation age, advances from the latter period producing the visually distinctive flights of terraceremnants. Both the terraces and the inner gorge, now occupied by the Shotover River, have been extensively worked for alluvial gold. Enrichments in the former environment have predominantly been as bottom or intermediate lags produced during degradation phases of catchment erosion. Surface lags have been locally targeted. Placer mining in terrace areas involved both tunnelling and sluicing techniques. In the modem river the greatest concentrations were on the schist or false bottoms, although flood gold has always contributed to the returns. Placer mining techniques here were highly variable.

Jan 1, 1998

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998