Search Documents

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.’s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feedgrade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

Jan 1, 1999

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By M. A. Llavona

The study of the formation and components of copper patina and its conservation has assumed great importance. The changing environment has accelerated the processes of patinas degradation; thus, the exhaustive study of factors capable of affecting the patina formation, growth and durability has assumed great importance for the industrial activity of copper. The main components of the patina, oxides, chlorides, nitrates and sulfates, have been determined; the effect of physical, chemical and microbiological factors on patina formation, particularly the influence of acid rain, natural organic matter, particles and microorganisms have been defined. The effect of different electrolytic solutions that accelerate the formation of copper patinas has been determined, and a review of the state of knowledge of the formation and evolution of metal patinas has been made.

Jan 1, 1999

By A. K. Sheik

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

The processes by which particles and bubbles interact capture many of the central concepts of colloid science and hydrodynamics. This area of research embraces hydrodynamics, interfacial(including capillary) forces, particle and bubble behaviour and solution chemistry. In this review, we discuss collision, attachment and stability efficiencies. We deal with the identification of a flotation ?domain?, the deformation of a bubble surface upon interaction with a solid surface, the kinetics of three phase contact line expansion and the determination of attachment efficiencies through to the direct measurement of bubble-particle interaction forces. We have recently carried out a test of collision theory where the latter embraces both inertial and centrifugal forces. The real challenge is now to quantitatively describe the behaviour of real systems and to incorporate a reliable description of the behaviour of particles in flotation froths. The approach described is very robust when applied to flotation, both from qualitative and quantitative points of view, providing an intellectual foundation for understanding this complex process in separation science and technology.

Jan 1, 1999

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

By Christian Hecker

An Eh-pH electrochemical sensor developed for on-line pH and redox potentials copper sulphide flotation process control was studied. The electrochemical sensor cell includes two metallic platinum electrodes, a metallic antimony electrode and a high impedance reference cell which are polarized with a potentiostat. For pH and redox potential determinations, the Sb and platinum electrode potentials are measured, respectively, against the polarized electrochemical reference system. The behaviour of this electrode configuration has been investigated in a laboratory scale. An electrochemical sensor device has been succesfully installed and checked in El Teninte Colon Concentrator's SAG line feeding the copper flotation rougher circuit.

Jan 1, 1999

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

This chapter looks at the development and use of the operating budget. This is management's plan of action in the short term, usually one year. The operating budget includes all expensed production costs (i.e., all costs reported as cost of goods sold) but does not include expenditures on capital equipment, which are usually justified using discounted cash flow techniques.

Jan 1, 1999

By Claus Becker

In Europe, approx. 50 km of traffic tunnels are under construction using Slurry-or EPB Shields or Convertibles of all sizes, among them the biggest slurry shield ever built up to now with 14,20 m diameter. Main characteristics and special features of the machines will be explained relating to geology, cover and water pressure. This gives a comprehensive overview of the latest developments of this kind of machines.

Jan 1, 1999

By Changshou Sun

Excessive deformation occurred in the underground openings of Jinchuan Nickel Mine, the largest nonferrous underground mine in China. Developed in weak rock formations at great depth, the underground openings are under great in-situ stresses with the horizontal stress being twice as high as the vertical one. Based on in-mine observations and in-situ testing results at the mine, time-dependent mite element simulations with coupled creep and plasticity constitutive models were conducted in this study to analyze the stability of underground openings In the study, the Burgers creep model and the Drucker-Prager plastic model were coupled to simulate underground drifts and cut-and-fill stopes. Two-dimensional finite element models were developed with ABAQUS - a comprehensive finite element simulation package The study investigated the behavior of underground drifts at great depth with high horizontal stress and the behavior of cut-and-fill stopes with various stope heights and fill conditions. The numerical simulations revealed important characteristics of opening deformations as a function of time after excavation and location relative to the wall of opening The results had good agreement with field monitoring data, They provided useful information to aid mine engineers in the design of mine openings, the selection of opening supports and the determination of support installation procedures.

Jan 1, 1999