Search Documents

By Mike Watts

Since the first longwall panel development started in the new mining, (Southern) area, a number of roof falls have occurred in L1 and L2 gate-entries. The longwall was delayed for a total of two months due to roof falls in the gate-entries. To prevent roof falls in future gate-entries, an extensive ground control analysis has been conducted which incorporated regional horizontal stress and panel orientation, tectonic stress, roof strata, surface stream valleys, etc. Results of the analysis indicate that a combination of these factors caused the roof falls. Therefore, a Roof Instability Rating (RIR) system was constructed to predict the roof condition and identify areas where supplemental support should be implemented. The L3 gate-entries, supported by the prediction using the RIR system, have not experienced any roof problems.

Jan 1, 2000

By Kenji Morinaga, Shigeru Fujino

"Preparation and vacuum ultraviolet (VUV) transmission spectra of aluminum fluoroberyllate glasses, MgF2-CaF2-SrF2-A1Fr BeF2 (MCSA-Be) and MgF2-CaF2-SrF2-AlFrYFrBeF2 (MCSAY-Be), were studied. The influence of YF3 and BeF2 on the thermal stabilization against crystallization and VUV transmittance was investigated. With increasing the BeF2 content, the crystallization tendency decreased and the absorption edge shifted to shorter wavelength in the MCSA-Be and MCSAY-Be glasses. The MCSA-20Be glass composition exhibited the shortest wavelength UV absorption edge (-147 nm) and the highest transmittance at 157 nm (60% for 2 mm sample thickness). The transmission values at 157 nm and the slope (steepness) of the absorption edge were found to be significantly influenced by the trace amount of Fe2+ derived from the BeF2 raw materials.IntroductionPure beryllium fluoride is known to be an only fluoride that forms one component glass on cooling from the molten state and is structurally similar to silica with [SiO4]4- tetrahedra. Molten BeF2 is highly viscous with a viscosity of about 106 poise near its liquidus temperature at 550""C[l]. The addition of modifying fluorides such as LiF, NaF or KF to BeF2 substantially decreases the viscosity[2]. Glass forming region of binary fluoroberyllate glasses has been mainly reported by several authors [3]. LiFBeF2 binary system is structually analogy for Mg0-Si02 system from their phase diagram and ratio of ionic radius for each cation and anion, respectively. LiF-BeF2 binary glasses seems to be promising candidates for the extreme deep vacuum ultraviolet (VUV) transmitting optical materials owing to their larger band gap. However, it is chemically unstable, and so, have no practical application for lens systems in micro lithography equipments and substrate materials for F2 (157nm) excimer laser[4]. There are also few reports on the VUV transparency of multicomponent aluminium fluoroberyllate glasses from the view point of their compositional dependencies. The purpose of this paper is to prepare deep VUV transmitting optical materials and determine the optimum glass compositions for aluminium fluoroberyllate glasses investigating their thermal stabilization against crystallization."

Jan 1, 2000

By S. Niyomwas, R. G. Reddy

"A mathematical model was developed to describe the plasma gas and particle dynamics and conversion yields. The velocity and temperature fields in the plasma were calculated by solving 1 the Navier-Stokes equations and the thermal energy balance equations. Conservation equations for the system species consider the multi-component diffusion and chemical reactions. Through the application of this model, temperature distribution, flow fields, and production rates were computed. The model was used to study the thermal decomposition of ilmenite in the non-transferred arc plasma reactor. The computed production rates of TiN from ilmenite using nitrogen and methane gas mixtures, are in the range of 5 to 100 x 104 kg/m3/s at 2500 KIntroductionThe widespread interest in thermal plasma processing has stimulated a great deal of research effort into the various aspects of this process, including plasma' spraying, thermal plasma chemical vapor deposition, plasma synthesis of fine powders, thermal plasma decomposition, plasma melting, and plasma extractive metallurgy.In the plasma synthesis of fine powders, the earlier experimental and theoretical studies aimed at predicting the final products1-5. Then it was followed by more recent investigation concerning the profile of plasma gas velocity, plasma temperature and concentration. In this regard, useful plasma processing models have been reported by numerous investigation6 -11 which were increased by both theoretical analysis and measurement.As a result of this work a reasonable plasma-processing model is proposed. It is to be noted that all the thermal analysis that has been made neglected the fluid -flow effects. Also, in the analysis aimed at the quantitative description of the fluid-flow field, the effect of heat transfer was not taken into account."

Jan 1, 2000

By M. Prasad, A. K. Majumder, T. C. Rao

The depletion of high-grade phosphate ores is bringing about a search for a suitable, economically viable technique that con process the abundant low-grade phosphate reserves. About 75% to 80% of the world's low-grade phosphate reserves are associated with carbonate gangue that is not amenable to treatment by the simple techniques of physical separation. The processing of sedimentary dolomitic/calcareousphosphate ore has numerous problems, including similar surface properties of the carbonate and phosphate. Two-stage reverse anionic flotation of carbonates (dolomite/calcite) has appeared to be a promising separation technique ,for the removal of carbonates from sedimentary rock phosphate. In reverse fatty-acid anionic flotation, the depression of phosphate mineral with orthophosphoric acid produces satisfactory results for calcareous as well as dolomitic phosphate ores from several locations of sedimentary origin.

Jan 1, 2000

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks capable of hauling payloads in excess of 290 t (320 st). Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Because truck haulage costs can account for 10% to 50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, but vehicle operating and maintenance costs would increase prohibitively. Thus, there is a need for improved design technologies encompassing the construction and management techniques of mine haul roads appropriate for the wheel loads of vehicles now in use. This paper presents the different components of a mine haul road design and management system and demonstrates the value of its application through case studies. The system has been applied at several South African surface mines, and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and provided better service, while the optimal selection and management of wearing course materials provided better functionality at lower total transportation operating costs.

Jan 1, 2000

By R. J. Snoby, P. Grotjohann

In processing heavy-mineral sands, the low feed concen¬tration and respective high value of the desired minerals require high-capacity production and sharp classification/ separation techniques to reduce the specific production costs. This paper describes the new allfux® separator, which can economically accomplish these criteria. The separator is a two-stage process that combines rising current and fluidized-bed technology. This allows for the treatment of ex¬tremely high mass flows in a single unit. This paper reports on test work performed on coal, iron ore and heavy minerals.

Jan 1, 2000

By G. V. R. Landman

In the early days of underground coal mining, the use of explosives to break coal resulted in a large number of disastrous methane and coal dust explosions and consequential loss of life. Research by the British, French, US authorities, amongst others, introduced many practices that significantly reduced the occurrence of such incidences. The use of explosives designed to be safe in a methane atmosphere, plus the creation of a second free face were two such practices which became commonly used in coal mines all over the world including southern Africa. With its associated coal cutting equipment and labour, the cost of creating a second free face is significant and this, together with the constant drive to reduce mining costs in a competitive market, causes mine management to regularly question the need for the second free face. Also, the safety and nature of permitted explosives has changed considerably since the days of black powder and nitroglycerine-based explosives with the introduction of water-based explosives. In southern Africa mining regulations pertaining to the blasting of coal has its origins in British research which was largely done in the first half of the twentieth century. More recent research by the US Bureau of Mine has resulted in a deeper understanding of some of the mechanisms of methane ignition by explosives and suggests that some of the earlier regulations can be relaxed to a certain extent without compromising safety. This paper gives an overview of the original research done in Europe and the more recent work in the USA, to give mine management and regulatory authorities a deeper understanding of the important safety issues when using explosives in a methane atmosphere. It also suggests that blasting off the solid is no less safe than using a second free face providing certain safety procedures are followed.

Jan 1, 2000

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By V. R. Voller

"The World Wide Web (the web) provides a very useful resource for the enhancement of teaching and research dissemination. This paper advocates that researchers take control of this resource and become actively involved in creating web content. Two examples of the use of the web in a materials setting is provided. The first illustrates how a concept quiz for teaching can be developed. The second shows how a materials processing model can be run in real time over the web. The paper closes with a summary of some resources that can be used to create web materials.IntroductionA recent copy of a newspaper advertisement read""Share what you know, learn what you don't""This neat phrase sums up a powerful teaching and research philosophy. In an educational setting a prime motivation for research is to uncover the unknown and venture in directions previously uncharted. The balance to this search for knowledge should be a desire to share that knowledge with others; whether it be with students in the classroom or research colleagues in a wider setting.The .World Wide Web and its associated multi-media software offer a perfect platform for researchers to share their knowledge with an extremely wide sector of the research community. To enable the use of this resource researchers must take the power that the web offers them into their own hands and create products that take maximum advantage of the medium. It is key that researches at the forefront become directly involved, otherwise a potential powerful medium will not realize it's true potential, and colorful products with no core content will proliferate. The object of this paper is to outline two ways in which the web can be used to enhance teaching and research objectives."

Jan 1, 2000

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By A S. M A Haseeb

Zircon is the second in abundance among the heavy minerals occurring in the beach sand along the coastal belt of Bangladesh. In this study a detailed characterisation of Bangladesh zircon extracted at the pilot plant of the Bangladesh Atomic Energy Commission at CoxÆs Bazar has been attempted using chemical analysis, X-ray diffraction and optical microscopy. From the chemical analysis it is found that Bangladesh zircon has a purity of 95.88 per cent. The main impurity in Bangladesh zircon is titanium oxide (3.01 per cent). This is followed by iron oxide (0.42 per cent). A number of other oxides are also found. Microscopic study revealed that Bangladesh zircon has an elongated, prismatic shape with pyramidal termination in about half of the grains while the rest are more or less rounded. Some fractured and irregular grains are also found. Bulk sample of Bangladesh zircon in the as-received condition shows a yellowish brown color. However, individual zircon grains are seen to be almost colourless and transparent under polarised light. XRD study confirmed good crystallinity in the sample. Under the microscope it is found that zircon grains constitute 94 per cent while total impurities amount to six per cent in Bangladesh zircon. This result agrees fairly well with the chemical analysis results. Microscopic study identifies oxides of titanium (both rutile and ilmenite) to be the main impurity, in conformity with the findings of chemical analysis. Further, monazite was also identified as an impurity under the microscope. An iron bearing coating is also found on a few zircon grains. Most of the impurities found in Bangladesh zircon exist as discrete minerals.

Jan 1, 2000