Search Documents

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By B J. van Loggerenberg

The capital cost of major items of mining equipment is very high. The operating cost of such equipment is also high. It is therefore important that such expensive equipment is used productively. To this end mine management uses production data systems and management accounting systems to monitor events and provide data for analysis to enable management to make operating and business optimisation decisions. This could be done better if there was an understanding of productivity in terms of its utilisation and efficiency components. What has been missing has been a methodology to properly account for the productivity of equipment in terms of its contribution in dollars to the costs and profit of the mine. An explanation of the Productivity Accounting methodology will be given. It will then be shown that productivity has two components, that of capacity utilisation and efficiency. These are defined and the dollar contribution of each to costs and profit shown. The efficiency component tracks the effect of proportional changes in input cost quantities used in the mining process as mining production changes. The capacity utilisation component tracks the effect of step changes in the input cost quantities used in the mining process as mining production changes.

Jan 1, 2003

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By Edgar E. Vidal

The deposition of ceramic materials onto substrates is of special interest in the development of surface related technologies. Research interest has been placed on using thermal plasma as the deposition method, specifically inductively coupled plasmas. Many different modifications to the same basic principle of deposition have been performed through out the materials research community. Such a technique may have many advantages over more conventional techniques, such as high deposition rates, high surface area coverage, clean energy source, no contamination from electrodes and operation near atmospheric pressures. Materials deposited vary from simple oxide systems like TiO2 to more complex structures like ternary oxides and nitrides. This paper reviews recent developments relative to the inductively coupled plasma deposition of thin films.

Jan 1, 2003

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By L. K. Daneshmend

"Competitive pressures dictate that the mining industry moves to larger mobile underground haulage equipment with more advanced equipment mechanization, higher levels of autonomous operation of machines, and longer periods between access by maintenance personnel. Since such new machines will of necessity be more complex than existing designs, machine reliability has become a key issue in progressing toward advanced mobile underground haulage equipment. Reliability and maintainability models of such equipment are practically non-existent in the literature. This paper addresses the issue of reliability and maintainability of mobile underground haulage equipment on two fronts: reliability modelling to enhance decision making for maintenance planning; and reliability simulation to enable evaluation of more rigorous production planning scenarios. A case study from a gold mine in the Chilean Andes is presented, for which reliability models of mobile underground haulage equipment, specifically load-hauldump vehicles and underground haul trucks, are developed, and a reliability-based simulation implemented. IntroductionMaintenance accounts for 20% to 35% of the overall operating budget for a typical underground operation, and hence represents the largest portion of the mine’s controllable operating costs (Cutifani et al., 1996; Campbell, 1997; Goddard, 1998). This, coupled with the fact that industry today is faced with an ever more complex and demanding marketplace, has led to an increasing interest in methods to reduce maintenance costs.Although significant effort has gone into developing effective maintenance strategies for industry in general, application of these to the"

Jan 1, 2003

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application, for geological structures, has been criticized, for its reliance on subjective interpretations. The Mine Safety & Health Administration's Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and. fault zones that were parallel with projected lineaments. The Roof Control Division's successful identification o f lineaments associated with roof falls and high wall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions would allow mine operators to obviate safety concerns that might otherwise adversely affect the health and safety of miners.

Jan 1, 2003

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003

By Gi-Chun Han, Ki-Suk Han, Korea Energy Management Corp., Jin-Sang Cho, Hyung-Seok Kim, Jae-Hyun Oh

This study has been carried out to use the waste sludges generated at Pohang Iron & Steel Co. Ltd. (POSCO) as the raw materials of Ordinary Portland Cement (OPC). The burnability index of the raw mixture and the hydration characteristics and compressive strength of clinker have been examined. The waste sludges were mainly composed of CaO, SiO2, Al2O3, and Fe2O3, the main component of OPC. The Burnability index of mixture was improved, according to the replacement content of POSCO sludge increase. POSCO sludge can be used as a raw material for cement because the state of mineral development and property of clinker produced from POSCO sludge are similar to the plain. Therefore, POSCO sludges can be used as the source materials of iron and calcium oxide.

Jan 1, 2003

By C. Siac

"It is a widely held view that in the 21st century, the mining industry will be dominated by a relatively small number of large companies, truly global in scope and internationally staffed (Gooding, 1997). Interestingly enough, most of the exploration and exploitation activities are being carried out by junior and major mining companies from common law jurisdictions in civil law countries, in particular in Latin America, where in recent years, the region has ranked first as a destination for exploration dollars, thanks to the reforms undertaken by some countries to amend their legal framework to attract foreign investment. From a lawyer’s point of view, this is where the main challenge lies: how to bridge the gap between the two legal systems.In order to avoid pitfalls, common law lawyers should be more diligent and proactive when dealing with civil law jurisdictions, given the different systems of law, standards, traditions and customs. Common law lawyers cannot be expected to be well-versed in civil law but they should not be completely unfamiliar with it either. A balance should be struck to ensure clients’ needs are professionally taken care of and that common law requirements and standards are met."

Jan 1, 2003

By Norihiro Murayama

Syntheses of zeolitic materials were carried out from coal fly ash by alkali hydrothermal treatment as part of the reuse and recycle technologies of coal ash, For the obtained zeolites, the cation exchange capacity and acid resistance, which are very important in the practical use of cation exchanger in aqueous solution, are investigated during this stufY, The cation exchange amounts of the NaP, CaP and K-CHA zeolites are measured for various cations such as K+, Na +, NH4+ Ca2+, Mg2+, Pb2+, Cd2+ and so on. The change in crystallization degree are researched as a function of pH. The simultaneous removal ability of NH4+ and PO43- in solution is examined for an example of the water purification with CaP zeolite. From these results, the characteristic and its mechanism of cation exchange are clarified for the various zeolitic materials obtained from coal fly ash.

Jan 1, 2003

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

Equity investments and loans are made in oil and gas and mining projects by the World Bank Group (WBG) as one piece of a multi-faceted quest to reduce poverty. The Bank mandate to reduce poverty through private sector investments has been contested by civil society organizations, so the Bank has established an independent review, entitled the Extractive Industries Review (EIR) www.eireview.org. The EIR is reviewing, from the perspective of affected stakeholders, the impacts and benefits of WBG development policy. In this paper, we review the indicators used by the WBG, academics and others to measure the effectiveness of investments. We argue that currently used frameworks and indicators do not capture local or regional data sets, and instead focus on available and easily aggregated information at the national level. A case review of the WBG?s International Finance Corporation (IFC) and Multilateral Insurance Guarantee Agency (MIGA) investments and loans in Sub-Saharan Africa provide material data buttressing the argument. Poverty studies in the extractive industries have a long way to go toward measuring and accounting for dollars spent and invested. The paper concludes with a call for project level and regional indicators to track poverty alleviation. Data gathered for this research was funded in part by the Extractive Industries Review.

Jan 1, 2003

By A W. Bewsher, T C. McCu, D B. Mapleson

The Miitel nickel sulfide deposit has been overprinted by a family of late stage structures that have acted as conduits for fluids that have contaminated the orebody with arsenic minerals. This has resulted in highly variable and unpredictable arsenic grades throughout the Miitel orebody. The ore produced from Miitel is processed under a toll-treatment agreement with Western Mining Resources Kambalda Nickel Concentrator. Part of this arrangement includes a financial penalty if monthly average arsenic grades in ore delivered exceed 800 ppm. This constraint has provided an extra challenge to the Miitel mine geologist in addition to daily underground duties. Routine development and stope mapping, close spaced sampling and cross-sectional interpretation were used in building an understanding of the structural controls of arsenic mineralisation and ore repetition at the Miitel nickel mine, and in providing maximum input to mine planning and scheduling. The distribution of structures responsible for arsenic introduction is now well understood from detailed mapping, sampling, and interpretation. By applying these insights to mine scheduling, the operation has successfully managed arsenic levels within the required specifications. Geological mapping has also improved the understanding of the structural complexity of the ore deposit, leading to the addition of ore tonnes and an increased confidence in resource modelling. Regular sampling and tight controls on data quality provided confidence in a strongly skewed arsenic data set. Multiple Indicator Kriging has been used for resource estimation of the arsenic contaminated nickel ore since it allows explicit control of the spatial influence of extreme grades in the positively skewed arsenic sample population. Both the grade control and exploration data sets are used to model the arsenic distribution.

Jan 1, 2003