Search Documents

By Walter E. Vanderpool

Three drilled foundations for an elevated water-tank were instrumented, tested and monitored during construction and the first two years in service. One shaft was load tested by the Osterberg method. A void was detected in one shaft by cross-hole sonic logging, pulse-echo logging and concrete coring. The void was instrumented, hydrostatically tested and pressure grouted. The shaft was ?abandoned? and replaced by two smaller shafts with a straddle beam cap. One of the replacement shafts and the cap were instrumented. The strain that appeared in the abandoned shaft, the replacement shaft and the cap were monitored during the remainder of the construction, through the commissioning test and the first two years of service. The results demonstrate the precision and sensitivity of the vibrating wire strain gage.

Jan 1, 2004

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

By Laurent Airaud

For around ten years, electronic detonators are available for those who want to use advanced methods and to apply theories promoted by engineers and professors to reduce blast concerns or improve fragmentation and dilution. Furthermore, decision makers can verify the use of electronic detonators to drive down mining costs. Engineers and more specifically blasters are the actual users and have to be convinced of the easiness of electronic detonators. This paper deals with electronic detonators and the notion of easiness. Common feelings about the notion of easiness are discussed. Then, examples of new technologies like, automobile, photography or Information Technology are discussed to observe how they progressed throughout time with new features and sales volume. For the specific explosive initiation industry, each step of the life of an electronic detonator is dealt with concerning the easiness and a table is used to quantify this notion.

Jan 1, 2004

By P. L. Duncanson, J. D. Toth

Since 1995, when "freeze lining" refractory systems were introduced to the ferroalloy industry, they have gained in popularity, due to the freeze lining?s reputation for reliability, safety, and the contribution it makes to profitability. As with many popular and effective technologies, however, the freeze lining has spawned low-cost pretenders that claim the "freeze lining" name. On the surface they appear to contain some of the components of the technology, such as thermally conductive materials, but they fail to incorporate all of the principles that define a true Freeze Lining. The term "freeze lining" refers to the refractory system?s ability to maintain a temperature profile that is low enough to freeze a layer of process material on its hot face, which insulates the refractory and prevents direct contact with molten metal and slag. In doing so, the common wear mechanisms found in the submerged arc furnace - chemical attack, erosion, and thermal stress - can be prevented. These wear mechanisms are all related to high temperature; thus, they are prevented by maintaining low temperatures. Certain refractory properties and design concepts are absolutely necessary for the lining system to function as a true Freeze Lining. The paper explains these requirements and why they are important - the Truth of freeze linings - and further explains why systems that ignore one or more of these requirements cannot claim to be freeze linings, thereby exposing the Myths.

Jan 1, 2004

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

By S. Afshar, E. Dajoux, C. Allaire

For various reasons, molten salts, mainly chlorides and fluorides, are used in the aluminum industry. In the holding and melting furnaces, these salts may have different roles such as protecting the metal from oxidation, reducing the metal content of the skim or removing inclusions or impurities from the metal bath. However, the use of these salts may also have some undesirable effects such as easy attack of the furnace lining refractory materials by molten aluminum. The aim of the present investigation was to clarify and to compare the effects of chloride versus fluoride salts, on the corrosion process of the aluminosilicate based refractory materials. A laboratory test and procedure, simulating the conditions at the metal line in the aluminum treatment furnaces, was used. Different aluminum alloys (A1-5wt.%Mg, A1-5.5wt.%Zn and 7075 alloy) and chloride or fluoride salts (MgC12, KC1, CaCl2, NaC1, MgF2, CaF2, NaF and cryolite) were used as well as several aluminosilicate materials. Thermogravimetric measurements were also carried out in order to analyze the effect of the salts on the oxidation of molten aluminum alloys. The experimental results showed that fluoride salts are more aggressive than chlorides against the tested refractory products. It is postulated that the fluorides prevent the formation of a protective oxide layer on the metal surface, favoring at the same time the corrosion of refractories. Moreover, it was found that the presence of Na in fluoride salts increases significantly the aggressiveness of the aluminum alloy towards the refractory samples.

Jan 1, 2004

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

Tailings facilities tell a story to the public about how the mining industry manages its activities. They also create a risk that must be managed for the long term. All the knowledge and technology is available to safely design, build, operate and decommission tailings facilities.   Tailings at Waikato North Head Minesite are pumped as slurry, over long distances and against high static discharge heads to backfill the excavated area. WNH is, under the mining licence, obliged to reconcile the topography of mined areas to the closest possible resemblance of the original terrain. The active tailings areas are located near main operational facilities and detailed plans and procedures have been developed to ensure a safe and continuous operation.   The concentration plant is designed as two identical and independent plants. Each plant has its own tailings slurry pumping system.   This paper represents a general overview of the tailings disposal practice at WNH mine site. It discusses tailings delivery, construction and water management.

Jan 1, 2004

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

The quantity, quality and detail of project information increases as project development moves from initial scoping level studies, to pre-feasibility and option studies, then definitive feasibility study and basic engineering stages. Data accumulates from metallurgical and vendor testing from various ore types and composites carried out to assess physical characteristics and processing responses of the ore. Over-simplification or assumptions about the orebody for flow sheet development can result in using æaverageÆ information for design. Use of averages of data can have adverse implications on sizing of plant and equipment and consequently on definitive study cost estimates and detailed engineering. In practice, the treatment plant workforce is faced with managing a non-homogeneous or non-average orebody in a variable operating environment that is not always predictable. This paper presents views on how to use the data generated from testwork in project development and for process and plant design. Examples of process design risk or operating risk are presented. Although this topic is applicable to the broad range of process design decision making in the minerals industry, this discussion references comminution, flotation and extraction processes for gold and base metal ores.

Jan 1, 2004

By F. W. Brackebusch, R. O. Sack

"A method for determining the fineness of Au in electrum from the composition of fahlore coexisting with pyrite and chalcopyrite is presented. This method is based on previously published experimental brackets and activitycomposition models for electrum and fahlore, and it is potentially useful for defining temperatures of hydrothermal mineralization and retrograde evolution of precious metals deposits. The authors demonstrate that it successfully predicts compositions of electrum reported for this assemblage in the literature and illustrate its application for three gold-quartz vein deposits from the Coeur d’Alene mining district, Idaho, that are prospects of the New Jersey Mining Company, the Coleman vein, High-Grade prospect, and Silver Strand mine. Temperatures calculated from average electrum compositions estimated from gravity concentrates (molar Au/(Au+Ag) = 0.76-0.39) and from microprobe analyses of the fahlores (molar Ag/(Ag+Cu) = 0.039 ± 0.004, Zn/(Zn+Fe) = 0.57 ± 0.03, As/(As+Sb) = 0.23 ± 0.02) from the Coleman vein indicate that the electrums underwent retrograde re-equilibration to temperatures between about 80°C and 240°C, roughly 80°C below the temperature of hydrothermal mineralization and 10°C to 40°C above the temperature inferred for retrograde equilibration of Fe and Zn between sphalerite and fahlore. Fahlores from the High-Grade prospect [molar Ag/(Ag+Cu) = 0.009 ± 0.004, Zn/(Zn+Fe) = 0.55 ± 0.11, and As/(As+Sb) = 0.04 ± 0.03] and Silver Strand mineralized zone [molar Ag/(Ag+Cu) = 0.10 ± 0.04, Zn/(Zn+Fe) = 0.63 ± 0.02, and As/(As+Sb) = 0.06 ± 0.02] exhibit strong core to rim depletions in Ag due to retrograde operation of the reaction1/10Cu10Fe2Sb4S13 + Ag + FeS2 =Cu-fahlore electrum pyriteCuFeS2 + 1/10Ag10Fe2Sb4S13chalcopyrite Ag-fahlorewhich proceeds to the left with decreasing temperature. Electrum inclusions in arsenopyrite from the High-Grade prospect [molar Au/(Au+Ag) = 0.90 ± 0.02] define a minimum bound on the temperature of hydrothermal mineralization of 273°C, and the temperatureelectrum composition curve constructed for the most Ag-rich fahlore in the Silver Strand mine indicates that the fineness of its electrum is significantly less than in the other deposits."

Jan 1, 2004

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By B. McLaughlin

"The Penna shaft is the deepest single-lift shaft in North America. Agnico-Eagle started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240-m deep shaft. Exploration success at depth led to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7000 t/d. The use of another double drum hoist, instead of a Blair multi-rope winder, to hoist 24.5 t skips was only made possible by lowering the safety factor.This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of 3 km. IntroductionThe original Penna production hoist was a 4.88 m (16 ft) diameter double drum and single clutch machine. Béliveau (1996) and Scott (1996) have described this hoisting plant. In 1998, a decision was made to increase mining capacity from 1800 t to 4500 t of ore per day from the shaft bottom. Final capacity had to include an allowance of 1800 t of waste per day for future capital projects. While daily capacity was to be 6300 t, it would, by taking into account the different rock densities, be equivalent to hoisting 7000 t of ore.The steps taken to lower the safety factor were presented by McLaughlin and Scott"

Jan 1, 2004

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004